Search found 4297 matches
- Thu Mar 28, 2024 1:10 pm
- Forum: General Discussion Forum
- Topic: A what is it question
- Replies: 8
- Views: 218
Re: A what is it question
You are correct Norm but it is a closed car cowl.
- Thu Mar 28, 2024 11:07 am
- Forum: General Discussion Forum
- Topic: Heater?
- Replies: 10
- Views: 324
Re: Heater?
I run one on our '19 Centerdoor - wife has a kick control register on her side - very functional !
- Thu Mar 28, 2024 11:01 am
- Forum: General Discussion Forum
- Topic: Rajo OHV question
- Replies: 8
- Views: 166
Re: Rajo OHV question
I'm running a nearly identical OHV set-up - my radiator started life as a Whippet but I had a new top tank made with Model T inlet & outlets - it cools O.K. but I'm also running a 5/8" shaft water circulator - been on several 200+ mile NWVSC events and have never boiled over.
- Wed Mar 27, 2024 8:00 pm
- Forum: General Discussion Forum
- Topic: Holley G Rebuild
- Replies: 10
- Views: 268
Re: Holley G Rebuild
Corey's done a handful of G's for me & some referrals - the G is quite particular on fuel level in the well - good luck !
- Wed Mar 27, 2024 7:57 pm
- Forum: Classifieds - Parts
- Topic: New U-Joint T-2571-A
- Replies: 2
- Views: 121
Re: New U-Joint T-2571-A
Hey Matt - did Norm close up ?
- Mon Mar 25, 2024 8:18 pm
- Forum: General Discussion Forum
- Topic: Model TT questions
- Replies: 11
- Views: 398
Re: Model TT questions
Ruckstell 2 speed axle. Front wheels are '26-'27 Model T wires wheels - get a better photo of the rears. Cab is remnants of a C-Cab.
- Mon Mar 25, 2024 1:11 pm
- Forum: General Discussion Forum
- Topic: An other dumb distributor question
- Replies: 5
- Views: 254
Re: An other dumb distributor question
Rader in California & I believe Reeder was in Texas
- Sun Mar 24, 2024 1:26 pm
- Forum: General Discussion Forum
- Topic: Mercury Update
- Replies: 17
- Views: 1192
Re: Mercury Update
Quite spiffy there, Andy !
- Sun Mar 24, 2024 1:25 pm
- Forum: General Discussion Forum
- Topic: 26/27 rear wheel drum rubbing
- Replies: 12
- Views: 328
Re: 26/27 rear wheel drum rubbing
Ford made a slick spring tool for those monster springs, Robert - 12"+ piece of 1" wide flat bar with a roll pin inserted at one end. I'll try & grab a photo later for you - makes it a much easier task !
- Sun Mar 24, 2024 1:22 pm
- Forum: General Discussion Forum
- Topic: Chicago transmission information
- Replies: 1
- Views: 144
Re: Chicago transmission information
Nice advertisement ! Wonder why the cost difference between the TT & the car ?
- Sun Mar 24, 2024 10:50 am
- Forum: General Discussion Forum
- Topic: Stevens Tools
- Replies: 7
- Views: 409
Re: Stevens Tools
Thanks for looking Michael !
- Sat Mar 23, 2024 5:30 pm
- Forum: General Discussion Forum
- Topic: Stevens Tools
- Replies: 7
- Views: 409
Re: Stevens Tools
Is there a date anywhere in there ?
- Sat Mar 23, 2024 2:35 pm
- Forum: General Discussion Forum
- Topic: Can this drag link be straightened?
- Replies: 14
- Views: 587
Re: Can this drag link be straightened?
Nice jig there, Ken !
- Sat Mar 23, 2024 11:35 am
- Forum: General Discussion Forum
- Topic: Refurbishing Steering Wheel
- Replies: 13
- Views: 692
Re: Refurbishing Steering Wheel
If it's cracked up, why not replace it - Bob's Antique Auto Parts was reproducing 16" black rims a number of years ago - I might still have one in stock.
- Fri Mar 22, 2024 7:16 pm
- Forum: General Discussion Forum
- Topic: Question about axle shaft length 1912 Runabout
- Replies: 11
- Views: 345
Re: Question about axle shaft length 1912 Runabout
He posted that both axles are original w/Ford script in the keyways.
- Fri Mar 22, 2024 4:17 pm
- Forum: General Discussion Forum
- Topic: Anyone recognize this 1914 T?
- Replies: 4
- Views: 502
Re: Anyone recognize this 1914 T?
Nice rig - perhaps make an inquiry over at the MTFCI - that looks like their sticker in the windshield.
- Thu Mar 21, 2024 1:34 pm
- Forum: General Discussion Forum
- Topic: Where did it go?
- Replies: 12
- Views: 683
Re: Where did it go?
First documented use of a "Bungee" !
- Thu Mar 21, 2024 11:47 am
- Forum: General Discussion Forum
- Topic: Model T aftermarket radiator?
- Replies: 18
- Views: 1153
Re: Model T aftermarket radiator?
There was a similar accessory shell listed on Ebay recently for some good $'s !
- Tue Mar 19, 2024 10:52 am
- Forum: General Discussion Forum
- Topic: Model T saw platform - PA lumber museum
- Replies: 3
- Views: 602
Re: Model T saw platform - PA lumber museum
Your reply made my day, Morgan !!!
- Mon Mar 18, 2024 8:32 pm
- Forum: Classifieds - Parts
- Topic: FS: New EGGE High Compression Pistons
- Replies: 4
- Views: 461
Re: FS: New EGGE High Compression Pistons
That's what the box states - STD.
- Mon Mar 18, 2024 1:02 pm
- Forum: General Discussion Forum
- Topic: Valve seat tool.
- Replies: 2
- Views: 252
Re: Valve seat tool.
I use them for carbon removal - Neway for seat cutting.
- Mon Mar 18, 2024 11:20 am
- Forum: General Discussion Forum
- Topic: Looking for Tut.
- Replies: 28
- Views: 1207
Re: Looking for Tut.
I see a hand crank on both George - first one appears to have a "crank holder". #1 sure appears to be an early Towncar.
- Sun Mar 17, 2024 8:26 pm
- Forum: General Discussion Forum
- Topic: Spark plugs
- Replies: 42
- Views: 2334
Re: Spark plugs
Get a small sauce pan on the stove a little better than 1/2 full & turn on the stove - set the float in the water and hold it down with a wooden spoon just before it stars to boil & watch for bubbles.
- Sat Mar 16, 2024 10:22 pm
- Forum: General Discussion Forum
- Topic: Firing order
- Replies: 20
- Views: 732
Re: Firing order
Model A is the same as a T, Norm.
- Fri Mar 15, 2024 6:42 pm
- Forum: Classifieds - Parts
- Topic: For Sale: Morshe/Lee Gas Gauge
- Replies: 2
- Views: 493
Re: For Sale: Morshe/Lee Gas Gauge
Gauge spoken for - thanks MTFCA !
- Fri Mar 15, 2024 1:14 pm
- Forum: General Discussion Forum
- Topic: New day timer
- Replies: 26
- Views: 1738
Re: New day timer
Haven't used or seen one of Tony's, Tim - it's unfortunate someone hasn't taken the reins on reproducing !
- Thu Mar 14, 2024 3:48 pm
- Forum: General Discussion Forum
- Topic: Front Spindle That Took a Hard Hit
- Replies: 5
- Views: 421
Re: Front Spindle That Took a Hard Hit
I have a similar spindle - NOS - factory defect !
- Thu Mar 14, 2024 11:39 am
- Forum: General Discussion Forum
- Topic: Using Coil Box Posts as a Junction Box
- Replies: 17
- Views: 583
Re: Using Coil Box Posts as a Junction Box
Norm - non starter cars had the switch on the coilbox.
- Thu Mar 14, 2024 8:21 am
- Forum: Classifieds - Parts
- Topic: TT high speed ring and pinion
- Replies: 2
- Views: 526
Re: TT high speed ring and pinion
5 to 1 +/_.
- Thu Mar 14, 2024 8:19 am
- Forum: Classifieds - Parts
- Topic: WTB crankshaft
- Replies: 6
- Views: 698
Re: WTB crankshaft
There's one going off on Ebay today that is ground.
- Wed Mar 13, 2024 7:36 pm
- Forum: General Discussion Forum
- Topic: What have you done to your Model T in March?
- Replies: 33
- Views: 1919
Re: What have you done to your Model T in March?
You gotta do what you gotta do, Dan ! I had the same task when I moved for retirement - couldn't take it all !
- Wed Mar 13, 2024 1:18 pm
- Forum: General Discussion Forum
- Topic: Trading up, or sideways?
- Replies: 4
- Views: 479
Re: Trading up, or sideways?
There's not alot of room in a '28 - '29 P/U !
- Wed Mar 13, 2024 12:04 pm
- Forum: General Discussion Forum
- Topic: Quick Poly?
- Replies: 7
- Views: 518
Re: Quick Poly?
A "temporary" repair to a wood wheel is most likely a bad idea !
- Tue Mar 12, 2024 5:31 pm
- Forum: General Discussion Forum
- Topic: New day timer
- Replies: 26
- Views: 1738
Re: New day timer
Ford experimented with a brush commutator in the early 20's.
- Tue Mar 12, 2024 5:30 pm
- Forum: Classifieds - Parts
- Topic: For Sale: Mint Standard Single Twist Horn
- Replies: 0
- Views: 165
For Sale: Mint Standard Single Twist Horn
Really nice Standard brand brass horn - $250.00 + the ride. Drop me a note.
- Tue Mar 12, 2024 5:26 pm
- Forum: Classifieds - Parts
- Topic: For Sale: Morshe/Lee Gas Gauge
- Replies: 2
- Views: 493
For Sale: Morshe/Lee Gas Gauge
Here's one of Tim's great "Night & Day" gas gauges - this is for a round tank. $125.00 + the ride.
- Tue Mar 12, 2024 5:23 pm
- Forum: Classifieds - Parts
- Topic: For Sale: NOS TT "Boot Scraper" Running Boards
- Replies: 0
- Views: 208
For Sale: NOS TT "Boot Scraper" Running Boards
Any interest in a mint NOS set of TT running boards ? $300.00 pr. + the ride. Drop me a note through the Forum, please.
- Tue Mar 12, 2024 5:19 pm
- Forum: General Discussion Forum
- Topic: Anderson timer history
- Replies: 5
- Views: 389
Re: Anderson timer history
The "trick" on Andersons is to retard the spark prior to shutting down - keeps the flapper from hanging up.
No lube on a New Day.
No lube on a New Day.
- Mon Mar 11, 2024 9:31 pm
- Forum: General Discussion Forum
- Topic: A Modified VW Distributor Problem
- Replies: 22
- Views: 1056
Re: A Modified VW Distributor Problem
Most if not all of the early Bosch conversions used a "bell crank" unit w/double spark arms - I understand the TTP conversion utilized a reverse cut gear to change the rotor direction thus eliminating the 2 spark control arms.
- Mon Mar 11, 2024 9:28 pm
- Forum: General Discussion Forum
- Topic: What have you done to your Model T in March?
- Replies: 33
- Views: 1919
Re: What have you done to your Model T in March?
Nice looking power plant & mechanic Bryant ! Is that your own "oil splasher" design ?
- Mon Mar 11, 2024 7:25 pm
- Forum: Classifieds - Parts
- Topic: WTB Front Fender Brackets
- Replies: 15
- Views: 547
Re: WTB Front Fender Brackets
My mistake - I had fender irons in my head !
- Mon Mar 11, 2024 4:07 pm
- Forum: Classifieds - Parts
- Topic: WTB Front Fender Brackets
- Replies: 15
- Views: 547
Re: WTB Front Fender Brackets
I have quite a few pair - '15 - '16 irons are a bit different at the headlamp post mount - they're "one-sided" as are the correct headlamp. Shipping them might be a bit of a problem - kinda long.
- Mon Mar 11, 2024 11:10 am
- Forum: Classifieds - Parts
- Topic: Frontenac Head Bound for Chickasha
- Replies: 4
- Views: 618
Re: Frontenac Head Bound for Chickasha
Thanks for the info.
- Sun Mar 10, 2024 7:43 pm
- Forum: General Discussion Forum
- Topic: Ignition key identification ?
- Replies: 17
- Views: 493
Re: Ignition key identification ?
John - are you able to post a photo of your switch ? Does it have Ford script below the headlamp lever ?
- Sun Mar 10, 2024 6:38 pm
- Forum: Classifieds - Parts
- Topic: Frontenac Head Bound for Chickasha
- Replies: 4
- Views: 618
Re: Frontenac Head Bound for Chickasha
What "model" T, S or R ?
- Sun Mar 10, 2024 2:33 pm
- Forum: General Discussion Forum
- Topic: Ignition key identification ?
- Replies: 17
- Views: 493
Re: Ignition key identification ?
I was under the impression that the repro switches were a #55 key.
- Sat Mar 09, 2024 1:07 pm
- Forum: Classifieds - Parts
- Topic: For Sale: Single Hassler rear shock absorbers. (Sold)
- Replies: 5
- Views: 363
Re: For Sale: Single Hassler rear shock absorbers
No worries, my friend !
- Sat Mar 09, 2024 11:06 am
- Forum: Classifieds - Parts
- Topic: FS Klaxonet Brass Hand Horn (SOLD)
- Replies: 4
- Views: 341
Re: FS Klaxonet Brass Hand Horn
I believe I have an original wooden box for that horn.
- Sat Mar 09, 2024 11:03 am
- Forum: Classifieds - Parts
- Topic: For Sale: Single Hassler rear shock absorbers. (Sold)
- Replies: 5
- Views: 363
Re: For Sale: Single Hassler front shocks absorbers
Those are "rears" Phillip.
- Fri Mar 08, 2024 11:08 pm
- Forum: General Discussion Forum
- Topic: Fuel filter
- Replies: 21
- Views: 860
Re: Fuel filter
All Ford sediments bulbs had a screen that I've ever taken apart.
- Fri Mar 08, 2024 9:29 pm
- Forum: General Discussion Forum
- Topic: Fuel filter
- Replies: 21
- Views: 860
Re: Fuel filter
I like John's lathe procedure - I might have to try that !
- Fri Mar 08, 2024 10:15 am
- Forum: General Discussion Forum
- Topic: Fuel shut off valve
- Replies: 16
- Views: 866
Re: Fuel shut off valve
I've been using the same tube of EZ Lube for 20 years - nothing in it's compound to go bad !
- Thu Mar 07, 2024 9:34 pm
- Forum: Classifieds - Parts
- Topic: WTB Martin-Parry Express Body Spare tire carrier
- Replies: 12
- Views: 644
Re: WTB Martin-Parry Express Body Spare tire carrier
"Improved" Model Coupe & Runabout spare carrier spool.
- Thu Mar 07, 2024 11:15 am
- Forum: General Discussion Forum
- Topic: Fuel shut off valve
- Replies: 16
- Views: 866
Re: Fuel shut off valve
Tim is correct - Time Saver is the lapping compound then re-assemble with Aviation fuel lube. The trick with the available valve is to lift up slightly while turning then slight downward pressure when you want it where it needs to be.
- Thu Mar 07, 2024 11:11 am
- Forum: Classifieds - Parts
- Topic: 26 fordor dash light
- Replies: 2
- Views: 145
Re: 26 fordor dash light
This is what an original Ford lamp looks like - I just recently sold it.
- Wed Mar 06, 2024 11:41 am
- Forum: Classifieds - Parts
- Topic: FS Used Drive Shaft Spool and Bearing Sets
- Replies: 4
- Views: 330
Re: FS Used Drive Shaft Spool and Bearing Sets
ANY twist is not serviceable - IMO.
- Tue Mar 05, 2024 7:47 pm
- Forum: General Discussion Forum
- Topic: Hang on buddy!
- Replies: 21
- Views: 1323
Re: Hang on buddy!
Were you a columnist in a previous life, Wayne ?
- Tue Mar 05, 2024 11:48 am
- Forum: General Discussion Forum
- Topic: Transmission brake drum
- Replies: 13
- Views: 773
Re: Transmission brake drum
J & M :
Yes we make the drums and gears and sold as an assembly.
Made exactly to the Ford print not a cheap copy.
What might you be referring to as " a cheap copy" ?
Yes we make the drums and gears and sold as an assembly.
Made exactly to the Ford print not a cheap copy.
What might you be referring to as " a cheap copy" ?
- Sun Mar 03, 2024 11:10 am
- Forum: Classifieds - Parts
- Topic: 6 volt Cutout -
- Replies: 7
- Views: 549
Re: 6 volt Cutout -
Jeff was wanting "original" can tops - not repros - he's having new cans produced now.
- Sat Mar 02, 2024 2:09 pm
- Forum: General Discussion Forum
- Topic: All the old gang.
- Replies: 9
- Views: 683
Re: All the old gang.
I like the early Touring full of gals (#12) with the accessory Sando pull starter on the front !
- Fri Mar 01, 2024 1:37 pm
- Forum: General Discussion Forum
- Topic: Need help re broken piece
- Replies: 18
- Views: 1108
Re: Need help re broken piece
Perhaps the stitch-n-loc on the larger pieces & weld the smaller pieces but I think the integrity of the mandrel might be compromised. I don't recall if they are cast iron or cast steel - used to be a method to verify by the color of the spark it throws off when hit with a grinder wheel.
- Fri Mar 01, 2024 11:44 am
- Forum: General Discussion Forum
- Topic: Need help re broken piece
- Replies: 18
- Views: 1108
Re: Need help re broken piece
OH CRAP Richard !
- Thu Feb 29, 2024 11:21 pm
- Forum: Classifieds - Parts
- Topic: Wanted: Bennett Brake Support Bar
- Replies: 5
- Views: 513
Re: Wanted: Bennett Brake Support Bar
Thanks for the additional photo Frank !
- Thu Feb 29, 2024 4:41 pm
- Forum: Classifieds - Parts
- Topic: WTB working brass sediment bulb
- Replies: 8
- Views: 482
Re: WTB working brass sediment bulb
Snyder's new repros are quite nice - we're lucky we can even get a new one !
- Thu Feb 29, 2024 1:48 pm
- Forum: General Discussion Forum
- Topic: What’s the story?
- Replies: 21
- Views: 1139
Re: What’s the story?
She doesn't appear to be a hefty gal - people were quite smaller statured back then.
- Thu Feb 29, 2024 1:45 pm
- Forum: General Discussion Forum
- Topic: Contact Me?
- Replies: 14
- Views: 1513
Re: Contact Me?
Hey there Buddy - glad to see you back !!!
- Thu Feb 29, 2024 1:43 pm
- Forum: Classifieds - Parts
- Topic: Wanted: Bennett Brake Support Bar
- Replies: 5
- Views: 513
Re: Wanted: Bennett Brake Support Bar
They attached around the h.b. cross shaft then over to a hogshead bolt - I have a photo somewhere around here showing them installed ! They were a "stiffener" to prevent the cross shaft from flexing.
- Tue Feb 27, 2024 10:03 pm
- Forum: General Discussion Forum
- Topic: Rekey Culm Ignition Switch
- Replies: 17
- Views: 864
Re: Rekey Culm Ignition Switch
Just a FYI - that Clum switch was for the earliest starter equipped cars - closed for sure - not sure about the open starter cars. It is the only year (1919) that utilized the cast light lever & fancy ammeter. I have that same Bosch panel (switched out the cast lever switch) in my Racer !
- Tue Feb 27, 2024 8:00 pm
- Forum: General Discussion Forum
- Topic: Rocky mtns and roughed up drums.
- Replies: 19
- Views: 1125
Re: Rocky mtns and roughed up drums.
I was going to suggest that too BUT if the R.M.s are mounted, not much room to manipulate the emery cloth !
- Tue Feb 27, 2024 3:53 pm
- Forum: Classifieds - Parts
- Topic: WTB steering gear drive pinion and brass wheel nut
- Replies: 2
- Views: 242
Re: WTB steering gear drive pinion and brass wheel nut
I have plenty - should be a 4-1 ratio unless you're running 21" tires - you pay the postage.
- Tue Feb 27, 2024 1:17 pm
- Forum: Classifieds - Parts
- Topic: Wanted: Bennett Brake Support Bar
- Replies: 5
- Views: 513
Wanted: Bennett Brake Support Bar
Anyone happen to have one or a pair of these ? They were supplied with the accessory Bennett Brake Kit.
- Tue Feb 27, 2024 12:54 pm
- Forum: General Discussion Forum
- Topic: Strange Transmission Brake band material
- Replies: 14
- Views: 925
Re: Strange Transmission Brake band material
I'll post a photo of the brake drum when the owner brings it back - pretty good "wear" pattern !
- Tue Feb 27, 2024 12:52 pm
- Forum: General Discussion Forum
- Topic: OLD PHOTO - Brass Era Self Starters
- Replies: 1
- Views: 364
Re: OLD PHOTO - Brass Era Self Starters
Haven't seen those types before - look at all the front spring leaves in the bottom photo !
- Tue Feb 27, 2024 12:48 pm
- Forum: Classifieds - Parts
- Topic: WTB hole filler speedo and accessory dash light.
- Replies: 14
- Views: 854
Re: WTB hole filler speedo and accessory dash light.
Stewart's had their own mounting bracket/plate held onto the dash with 3 ? small machine screws & nuts - you'd see the holes.
- Tue Feb 27, 2024 11:29 am
- Forum: General Discussion Forum
- Topic: Strange Transmission Brake band material
- Replies: 14
- Views: 925
Re: Strange Brake band material
Yep - have an engine & trans. job in the shop now that had that type of brass impregnated hard lining on the brake only - too hard IMO - I recall back in the 60's - 70's where "brake & clutch" from fork lifts & Cats was being used.
- Tue Feb 27, 2024 11:22 am
- Forum: Classifieds - Parts
- Topic: For Sale: More goodies !
- Replies: 5
- Views: 980
Re: For Sale: More goodies !
BTT - open to offers - I got too much stuff !
- Mon Feb 26, 2024 10:02 pm
- Forum: Classifieds - Parts
- Topic: WTB hole filler speedo and accessory dash light.
- Replies: 14
- Views: 854
Re: WTB hole filler speedo and accessory dash light.
Most likely an AC speedometer head was in the hole - they have 2 studs on the rear & a bar type holder. The dash lamp appears to be an original Ford accessory lamp - measure the "minor" diameter- I have some assorted covers.
- Mon Feb 26, 2024 8:00 pm
- Forum: General Discussion Forum
- Topic: Rocky mtns and roughed up drums.
- Replies: 19
- Views: 1125
Re: Rocky mtns and roughed up drums.
I'd dress them down if they were mine.
- Mon Feb 26, 2024 7:56 pm
- Forum: General Discussion Forum
- Topic: Front spring mount and cross member
- Replies: 20
- Views: 1136
Re: Front spring mount and cross member
"Suicide" was coined due to the fact your front axle IS NOT where it was originally placed from the factory - that's my understanding of the phrase.
Mine is way out there !
Mine is way out there !
- Mon Feb 26, 2024 7:53 pm
- Forum: General Discussion Forum
- Topic: Which steering column is 1916?
- Replies: 10
- Views: 645
Re: Which steering column is 1916?
What type of horn wire tube is yours Russ ?
- Mon Feb 26, 2024 7:50 pm
- Forum: General Discussion Forum
- Topic: Spark plugs
- Replies: 42
- Views: 2334
Re: Spark plugs
Yes it is Vincent - looks like a Rader unit.
- Mon Feb 26, 2024 7:48 pm
- Forum: Classifieds - Parts
- Topic: 6 volt Cutout -
- Replies: 7
- Views: 549
Re: 6 volt regulator
That is a cut-out - not a regulator - BIG difference !
- Mon Feb 26, 2024 5:23 pm
- Forum: General Discussion Forum
- Topic: Front spring mount and cross member
- Replies: 20
- Views: 1136
Re: Front spring mount and cross member
I have a somewhat similar "suicide" front spring mount on my Racer and you DON'T want any movement up front !
- Mon Feb 26, 2024 5:21 pm
- Forum: General Discussion Forum
- Topic: Which steering column is 1916?
- Replies: 10
- Views: 645
Re: Which steering column is 1916?
I've had both types of columns with the small horn tube - I'm going to venture a WAG that the single wire round tube was earlier than the simple single wire U-channel - simple economics perhaps ?
- Mon Feb 26, 2024 3:50 pm
- Forum: General Discussion Forum
- Topic: TT Aux Tranny?
- Replies: 5
- Views: 548
Re: TT Aux Tranny?
There were several variations of that - 2 speed & 3 speed - Seattle Transmission and or Tractor Train Co. was another.
- Mon Feb 26, 2024 3:47 pm
- Forum: General Discussion Forum
- Topic: timer or distributer
- Replies: 24
- Views: 1044
Re: timer or distributer
I run a twin spark distributor on my BB RAJO - Zoom - Zoom !
- Mon Feb 26, 2024 3:44 pm
- Forum: Classifieds - Parts
- Topic: WTB. Running Board Brackets
- Replies: 6
- Views: 414
Re: WTB. Running Board Brackets
2 or 4 of the brackets GG ?
- Mon Feb 26, 2024 11:10 am
- Forum: General Discussion Forum
- Topic: Spark plugs
- Replies: 42
- Views: 2334
Re: Spark plugs
Appears to be an older Bill Rader distributor set-up - uses a Bosch 009. Does it utilize a "bell crank" assembly for spark advance ? Meaning 2 spark
rods & a bell crank ?
Point gap 018 - .020 - with a distributor ignition, I run my plugs at .032 - .035.
rods & a bell crank ?
Point gap 018 - .020 - with a distributor ignition, I run my plugs at .032 - .035.
- Sun Feb 25, 2024 2:06 pm
- Forum: Classifieds - Parts
- Topic: Winfield Carburetor wanted
- Replies: 6
- Views: 670
Re: Winfield Carburetor wanted
Yes, they are that would be complete & runnable !
- Sun Feb 25, 2024 12:43 pm
- Forum: Classifieds - Parts
- Topic: WTB. Running Board Brackets
- Replies: 6
- Views: 414
Re: WTB. Running Board Brackets
I have a bunch - let me see how to package them.
- Sat Feb 24, 2024 10:57 am
- Forum: Classifieds - Parts
- Topic: For Sale: Spring Cleaning Again !
- Replies: 9
- Views: 1262
Re: For Sale: Spring Cleaning Again !
Truck bracket is sold - open to offers ! That shorter bracket w/3 mounting holes is for a 1915 Touring only - I don't have the license holder. The w.s. hinges are '15 - '16.
- Sat Feb 24, 2024 10:57 am
- Forum: Classifieds - Parts
- Topic: For Sale: More goodies !
- Replies: 5
- Views: 980
Re: For Sale: More goodies !
BTT - open to offers.
- Fri Feb 23, 2024 10:47 am
- Forum: Classifieds - Parts
- Topic: For Sale: More goodies !
- Replies: 5
- Views: 980
Re: For Sale: More goodies !
W.S. stay rods spoken for.
- Thu Feb 22, 2024 10:03 pm
- Forum: Classifieds - Parts
- Topic: For Sale: Spring Cleaning Again !
- Replies: 9
- Views: 1262
Re: For Sale: Spring Cleaning Again !
The mirrors are sold - thanks for the interest fellas ! Thanks MTFCA !
- Thu Feb 22, 2024 7:51 pm
- Forum: Classifieds - Parts
- Topic: For Sale: Spring Cleaning Again !
- Replies: 9
- Views: 1262
Re: For Sale: Spring Cleaning Again !
I intended for the mirrors to be sold as the pair as they are a matched set - my apologies for any confusion !
- Thu Feb 22, 2024 7:36 pm
- Forum: General Discussion Forum
- Topic: radiator
- Replies: 12
- Views: 906
Re: radiator
Simple plate, spring, stud, leather pad, nut & cotter pin. Thimbles won't work with a brass radiator !
- Thu Feb 22, 2024 7:33 pm
- Forum: Classifieds - Parts
- Topic: For Sale: More goodies !
- Replies: 5
- Views: 980
For Sale: More goodies !
Here's a few more goodies I rustled up - drop me a note for particulars and/or questions, please. Windshield stay rods,brass w/clamps - $250 + the ride - oversize. Large searchlight yoke - heavy - $150. Thomas timer elevator - complete - $250 NOS TT "boot scraper" running boards - $300 for the pair....
- Thu Feb 22, 2024 11:42 am
- Forum: Classifieds - Parts
- Topic: For Sale: Spring Cleaning Again !
- Replies: 2
- Views: 722
Re: For Sale: Spring Cleaning Again !
All the above spoken for - thanks MTFCA !
- Thu Feb 22, 2024 11:40 am
- Forum: Classifieds - Parts
- Topic: For Sale: Spring Cleaning Again !
- Replies: 9
- Views: 1262
Re: For Sale: Spring Cleaning Again !
Front license bracket & one '13 - '14 Touring rear lamp bracket spoken for and several in line for the mirrors - I'll keep mirror folks apprised. Stewart gear & Standex gauge tentatively spoken for.
- Wed Feb 21, 2024 10:02 pm
- Forum: Classifieds - Parts
- Topic: For Sale: Spring Cleaning Again !
- Replies: 9
- Views: 1262
Re: For Sale: Spring Cleaning Again !
Speedo bracket spoken for - thanks MTFCA !