MTFCA Forum

Looking for a set of front wheels for a 1911 Touring. 2- 30x3 wooden round fellow wheel in good shape. Thanks
email bpresslyLSMO(at)aol(dot)com

I have two examples of the early band adjusting wrench I would sell. One has been wire brushed and one has not.
Your choice $20+shipping
[image][/image]

What is the intended purpose of the third hole in the camshaft flange and does it's orientation matter in the timing of the large timing gear to small timing gear?[image][/image]

I'll buy it. How do you want payment? Shipping would be to 64086

Shown in Volumn XXVII, page 51...https://www.google.com/books/edition/Motor_Age/DlswzxvVrf8C?hl=en&gbpv=1&dq=off-an-on+tire+tool&pg=RA5-PA51&printsec=frontcover It was popular enough when new that Stewart had to sue the American Auto Supply Company around 1915 to stop using the "off-an-on tire tool...

Stewart Off & On Tire Tool No.3
Patent Applied For
about 13 inches long
looks like it uses a handle extension
anyone every seen one before or have any additional info?

I have a late 1913 engine (#369365) in my 1914 Depot Hack with what appears to be a correct narrow snout crankcase (oil pan w/ 3 dip inspection plate). I removed the radiator and fan to provide good access to the front cover. My original intent was to correct two problems: leaking crankshaft seal an...

You get an A+ for cleverness, but if you don't have a stock "T" cam, that was quite an exercise in futility. A new cam has been designed for a VERY small pushrod gap and now that you have a new cam and wide open clearances (as listed in the manual), you've gained a noisy engine and have probably de...

Here's a sketch of my tool in the cylinder
.
.
.
After all valve adjustments were completed, I double checked the valve lash gaps and compared them to the gaps listed within the original manual - all within the range listed!!!

117169205_10158579745537910_6336752155796498151_n.jpg Tool inserted in the bore with piston at 'bottom dead center'. Threaded rod adjusted and locked with the top of the tool even with the top of the block. . 117389757_10158579745582910_8293574213168440069_n.jpg The crank is positioned with the too...

"The method of accurate valve timing on a Model T Ford engine is to time the valves by piston travel" per Ford Service Bulletin released December 1924. It accommodates a worn cam, but also works with a new standard cam. I figured out an alternate way to use the KRWilson method of adjusting 'valve ti...

John.Zibell wrote: ↑

Sun Jul 25, 2021 12:56 pm

John.Zibell wrote: ↑

Fri Jul 16, 2021 9:31 am

message sent

Bill didn't accept my offer. Waiting to see if he decides to accept.

A local family from Wellsville came and bought it today for $11K

Back up for sale

My much older good friend, Bill Kelly in the Kansas City area is offering his 1926 Ford Model T Touring for sale. It runs good on magneto or battery. The tires, top and upholstery look very good. It has wire wheels and wind wings. The paint decent. He went thru the motor and drivetrain many years ag...

Hi Dave, Welcome to the Model T world. It's great fun and as you have seen many good folks will join in to give you help. The Kansas City Chuggers is the local Model T club and we affiliate with the MTFCA and the MTFCI. We of course are not meeting because of the virus, but you can visit our websit...

[image][/image]See attached

SOLD

SOLD

2013 Suretrac 14 ft Enclosed Cargo Trailer setup to haul a tall Model T Ford. $5250.00 Kansas City Area GVWR 7000# 3 inch bottom exterior alum trim 16 inch OC floor supports 18 inch extra height 3/8 inch interior plywood walls passenger side access door positioned for Model T entry both axles have e...

Sound like a plan John

Model T Ford Runabout (Turtle-Back) Trunk, 1917-1922 Style w/ pressed steel handles. Looks to have original solid wood frame without repairs or patches. This may have been installed on a 1919, because of the battery box cutout shown. $350 Could deliver to Chickasha, if you are going.