MTFCA Forum

Steve Bender

I'll be bringing my coils. Looking forward to seeing the results!

Steve Bender · Re: 37 DAYS TILL CHICKASHA 3-15-16-2024 Will there be any tire vendors?

Will there be any tire vendors?

Steve Bender

Awesome thanks Dave

Steve Bender

Wtb Rocky mountain brakes for large drum.
26 - 27

Steve Bender

I am interested.

Steve Bender

This is the part I need. Took me a while to figure out how to post pic.

Steve Bender

Steve Bender

That's right the handle broke just inside the latch mechanism it's all one assembly.

Steve Bender

Yep it fits on the inside. The handle is the same for left driver side rear and the front passenger side. If that helps. I will post a pic later.

Steve Bender

I need a door handle for 1923 touring right front passenger side. Mine broke makes it hard to get in and out. But it does now have a General Lee feel to it!

Steve Bender

I was referring to the drive shaft not the housing that it rides in. It must be a replacement not original Ford. There is no Ford markings and no dot marks in the center. I believe the dot was a test for hardness ?

Steve Bender

Compared to all the stock driveshafts that I have it is significantly larger diameter. I'll measure it when I get home.

Steve Bender

I picked up a driveshaft that has the original pinion set up with the sleeve and ballbearings set up just like stock. The other end has machine square end for U joint just like stock. The center section is much larger diameter. I can't see any markings. Was there any variation between years? Was the...

Steve Bender

I would take one

Steve Bender

I'm looking for a Ruckstell rear end that I could rebuild.
I prefer a 26/27 or even a left side ruckstell housing. I would also consider earlier ruckstell. Like to pickup at Chickasha pre war meet. Please email me or you can text to 316 640 5026.

Thanks
Steve Bender

Steve Bender

I'm interested message sent.

Steve Bender

I was hoping to find a single original one. Lang's sells them in pairs.

Steve Bender

: images.png (3.7 KiB) Viewed 1128 times

Here is picture of what I'm looking to find.

Steve Bender

I need one straight top saddle support arm for 1924 touring.

Steve Bender

Can't wait to be there!

Steve Bender

What is the advantages or disadvantage if using timesaver?

Steve Bender

Agreed they must have done it out of the block or the babbitt would have melted out. The surface is built up so much I don't think a cap would fit.

Steve Bender

I would think you would have to have removed the crank to do it. It would have been much simpler to take just the cap off and add babbitt.

Steve Bender

I don't think the person selling it knew. It was covered in thick old grease and appeared so for a very long time all the journals are round and measure close to standard so we thought it was a good one until I got home and cleaned it up. I don't understand why you would do this to fix the end play ...

Steve Bender

I purchased this crankshaft at Chickashee and cleaned it up to use in a spare engine. There appears that someone used brazing on the inside of the third main. Why would they do this? Is there anyway to clean it up?

Steve Bender

: image000003 - Copy (2) (1).jpg (74.82 KiB) Viewed 3076 times

Steve Bender

: image000001.jpg (65.67 KiB) Viewed 3078 times

Steve Bender

I also have an auto polo car but have no one to play.

Steve Bender

Please send pics.
orldrn.sb@gmail.com

Steve Bender

Looking for floorboards for 24 touring to pick up in Chickasha.

Steve Bender

Wtb .030 model t lite connecting rods to be picked up at Chickasha meet.

Steve Bender

Sent email yesterday am

Steve Bender

I would take them.

Steve Bender
316 640 5026
Orldrn.sb@gmail.com

Steve Bender

How about 26 - 27 radius rods? I would be interested if you have some to bring.

Steve Bender

that's great news!!!!

Steve Bender

Dan,
I did use the copper gaskets. I lined up the clamps and tighten them and just got enough room for it to miss the frame.

Thanks to all for advice.

Steve

Steve Bender

Is there a difference in early vs later intake manifolds?

Steve Bender

Thanks

Steve Bender

I have a stromberg of I was trying to install. The bowl hits the frame so the bolt holes from the intake manifold and carb dosnt ]line up. What needs to be done to install.

Search found 39 matches