MTFCA Forum

Looking for a good used pedal pad assembly for a 28 with multiple disc clutch. ( goes around steering column and pedals to seal). I know they make new ones but I have an original unrestored car and new parts just stick out like a sore thumb.

Found one, thanks everyone!

Still looking, thanks in advance

Looking for a model a multiple disc clutch fixture used to rebuild early multiple disc clutches. Thanks in advance

I have a wide drum ruckstell I recently completely went through and rebuilt. I replaced everything that was warm out of speck per the rebuild manual, many new ruckstell parts and new axles. I was going to install in my touring but plans have changed. $3500. Have wood brake drums that will go with it...

Would you be able to ship ?

Sent you a pm, have a new unused set

Snyder’s has them in stock , P/N. T-7831. $ 1.25

I know rootlieb makes new wide track fenders but I thought I’d see what’s out there. Have an early (March) 14 touring wide track. My rear fenders are not salvageable so I’d like to find a good original 13-14 set. I’ll order new ones if I have to but would like to see what’s out there before I make m...

Thank you , my plan is to change over to the late style shift lock. Right now just wanting to get it as safe as possible with what I have .. until I get a late style p158c to swap out with the one I have.

I am rebuilding a large drum ruckstell. My question is the shift lock is an early brass one. Are the parts internal interchangeable with the second generation cast ones ? My p113 shift clevis shows signs of wear and chips at the two lock notches.

I am planning on installing a ruckstell in my 24. Will be getting a kit from one of the parts suppliers. The car currently drives well with no rear end noise or issues at all. Whit that being said what should I expect at the least, other parts should I plan on. I know I have to replace the thrust wa...

Finally found the rattling sound inside my 24. Wasn’t noticeable until I had the oil drained and was hand cranking in prep to check rod clearances. Wonder how long it was loose. Fortunately the threads inside the disc drum are fine. The Cotter pin must have been left out somewhere in its 97 years

There is a good one in Franklin next weekend Friday and Saturday at the fairgrounds . Little bit of everything there. Model a and t stuff is always there

Thanks for the information! My confusion came from watching the install video on the classtique kit and was comparing how my directions for the cartouche kit I am installing. She mentioned in the video to not fasten to the third from the back bow only the other 3 and my kit says to tack the padding ...

Great ! Thank you . One last question, do you tack the pads to all the bows or just the rear two and front ?

That’s what I was thinking, greatly appreciate the help!

I am installing a top on my 24 touring. Has anyone installed a kit from cartouche? Iv watched a few videos and there kit install seems to be different then how clastique installs there kit . Particularly how the wind breaker installs at the windshield. Has anyone installed this kit and have pictures...

Thanks you !

Anyone have a drawing or plans for a wheel press. Have loose spokes so time to replace a few. Thanks !

I had found that to be true as well. At least that is the set up I have on my rear top iron. Only common sense faster on the rear is the very upper corner one, the other ones are pin and dot type

Anyone have a 23-25 touring with side curtains? I’m looking to find how they fasten in the middle on my 24 . My common sense fasteners are as fallows. Two in the front along the curve of the top and one upper corner of rear of bow and the three dot studs on the rear bow riser along with the small br...

I’m looking to buy a set if ac brakes, Lary sidmore I hear is the guy. I tried the email that is listed on here and it seems to be a old one and not working. Does anyone have a good email for him so I can order a set ?

Unfortunately Richard is not making linkage kits at this time. He says hopefully in the near future he will be able to start up again. Is there anyone else making linkage?

Perfect, thank you

Thank you !

Thank you, i don’t like the rockys that Snyder’s have since they don’t work in reverse and disc kits don’t look well on a 100 year old car. I hear these work well . Anyone still making the linkage set up ?

I’d there anyone still making the ac brakes and linkage kits ?

Is there anyone still making ac brakes and the linkage kits ?