MTFCA Forum

Couldn't locate anything using the forum search for my concerns...
Was looking for some pictures (and guidance) of other's T's showing valves properly seated and without head installed.

On the last start up, I noticed coolant bubbling out from the rear head and knew I needed to replace the head gasket.
Today I got the head removed, spent an hour...

My 27 touring has a crack / bend in the the lower section of the the front bow. Wondering is I should attempt to repair on the car?
I have a lathe so I could cut it off at the break and make a dowel to fit inside, then braze up the joint.
Anybody tried this repair?

I'm having a brain cramp, what book lists the various bolt sizes used on a Model T chassis and body? Thanks, Art

I just saw a 26-27 T roadster pickup for sale in Longview, Texas by a salvage yard on Facebook marketplace. Price $2500.00. Ad states no title, no motor or transmission, and I do not see top irons or bows. Picture is not a close up, but it doesn't look like a rust bucket and fenders don't look all bent up.

Doing a full rebuild on my 22 centerdoor engine. Everything shows minimal wear so i ordered standard adjustable lifters. The problem is they wont go into the block. They seem to be one or two thousandths too big. Suggestions? Is there a reamer out there that would work for this?

Some years back RV Anderson reproduced a Watts style clutch. The price of the original material skyrocket and he used a ditterent material and asked some who purchased the kit to critique it. I have a 26-27 set up but am reluctant to install it fearing it wont work well. If anyone has experience with this clutch, good or bad, I'd like to hear from...

Removed mosquitoes.

smoked.jpg

Do you guys have a source for 21 tires other than Lang's or Snyders? Just curios if I'm missing something. I'm pretty happy with the results of my wheels and I just can't bring myself to put the old whitewalls back on. I have Kelsey split rims and only 1 of them is good. I saw a guy sell his rims and tires here but missed it dang it ;-)

Just...

Hi everyone,
Just completed going through the entire Ruckstell in a ,26 Tudor that also has a Warford transmission. Having both I thought it a good idea to install the hydraulic disc brakes which I just finished today. Got everything put back together and started the engine to make sure the Warford shifted correctly which it did, however I could...

This wheel/star with 6 holes is attached to the original choke arm where the wire goes. What is its purpose? It doesn’t spin, it has raised areas that lock it in place.

I'm surprised no one has mentioned the 1911/12 Town Car which is on facebook. This vehicle is in excellent original condition and must have been stored in a very friendly envionment for over 100 years. Their was a video showing the outside and inside which is remarkable condition it has since been deleted My Town Car is very close to this vehicle...

I have a 16 valve Roof, believe it’s a model A with oval exhaust ports and two 8 valve Roofs, one has a single intake port and the other has two intake ports. Would like to know what they may be worth? They have all had some repairs done, the dual intake 8 valve may not be useable. I think the 16 valve and single port 8 valve are useable. Please...

Need some help!!
Anyone have a idea who made this radiator shell?
Picked up at a auction and would like to know more about it
Thanks for any help
Rick.

Hi everyone,
I just finished installing new axle shafts in a Ruckstell differential and I’m wondering if I did right to use anti seize on the tapers. Evidently there has been some debate on the matter. I also installed new hubs. Any thoughts appreciated!

I have two glass spare headlight reflectors. They are both the same diameter, but one is thicker and heavier than the other. Since the headlights are John Brown, I would assume the lighter one would be what was used. I'm not willing to remove the reflectors from either one of my '13s to find out!

How does one remove the front seat cushion ( back) on a 27 touring?
This one was recently re upholstered, looks like the covering is stapled in place, if so does this require pulling all the staples and then replacing them?

Hey guys I need more advice. 1926 Coupe here.

Problem:

So I have new triple gear bushings with 10 Thousands thrust.
The driven gear is pressed flush with the brake drum shaft.
New transmission shaft from Lang's.
Trans shaft installed as far as it will go and torqued to spec.
When I took it apart it had the three thrust washers for the clutch...

I’m ready to put new sneakers on my ‘26 split rims and am considering going with 5.25-21. My engine is strong and I do have a Rux in this pickup. I like the idea of the slightly larger diameter tires giving me a little lower rpm at the same cruise speed. What have others experienced? Also, what’s the current opinion of the various brands that are...

Does this date really mean anything for a Model T or is it only because it is used on aircraft?
Why does it expire? Looks like vaseline in a tube.
Thank you.

Hey there Model T friends. This is my first post in a good while. As most of you know already, I own a 1926 TT. I have not driven my truck all that much in the past few years and that it=s due to one central reason. Almost every spoke out of the 48 on the car is loose. This looseness causes the truck to walk all over the place when I'm driving and...

Does anyone know if there’s a difference between Canadian coil boxes and US coil boxes. I have a 1922 Canadian tourer… the coil box needs rebuilt. The wood isn’t the correct thickness and when the lid is on I short out coils….

I either want to buy a rebuild kit, or maybe someone has a nice rebuilt one ready to go for me?

Thanks for your help!...

I know the 2nd owner started a partial restoration on Daisy in the mid/late 60's after being stored since 1935.
Cleaning up the wood on her, while the firewall is original, the hood boards are replacements built by Syverson Cabinet, from their Des Plaines location they vacated mid 60's.
Just some continuing interesting archeology......

IMG_5109.jpeg IMG_4990.jpeg IMG_5044.jpeg IMG_5004.jpeg

I am looking for a TT cab for a new project I'm working on. I have a complete running 26 chassis. My buddy found a TT flat bed with all the stock racks in amazing condition. I will get pics posted soon. Just seeing what is available within reasonable distance.

Has anyone ever taking an Aluminum replacement pulley that is not adjustable and make it adjustable?
I have one that is not snd want to make it that way.
Thanks Dan

As subject line states...this is the last week I will take requests for brushes to be custom made for the TW timer.
See my listing in the parts section. Thank you.

Can someone please provide the measurement of the front top bow from the locking pin at the bottom of the iron to the top of the wood bow? Thank you!

It has a Rootlieb flat wood dashboard. I want to add a sheet metal cowl. more of a curved shape. Any ideas or does anyone have one for sale? or a blue print or patterns?

thnx
frontyboy.

Just respond here is the best

Get it for your grandkids! Get it for yourself!
To be issued in March.

LEGO 11376 Ford Model T celebrates the revolutionary automobile - Jay's Brick Blog

All,
The Bay Area Horseless Carriage Club is stepping in to take over the “Bakersfield” swap meet. The event will be the same location and date, Price per space will be 65 dollars. More information will be forthcoming soon.

This is just a quick announcement moments after the vote to let everyone know Bakersfield Lives again.

More to Follow

Cab anyone with a hempy cooper line boring set up take some measurements and pictures of the cutters for me mine are missing

I am looking for the proper name of the sheet metal cover that attached to the wood firewall ( 1915 ) and
covers where the rear of the motor sticks out.
I also assume it transitions down to the floor board.
I am also looking for a source for this item or a drawing for fabricating as a last resort.

Thank you

Enjoy a short ten minute drive in the rain in Hawaii. Have a great day!

New year, new thread. Our chapter has done nothing so far. 1 1/2 inches of rain today. I wanted to start the thread in case someone did something worth sharing.

Andy
Redwood Empire Model T Club

it is getting to be time to start planning our springtime auto. activities ... i spoke with Kevin Hammock this week regarding any changes in the Duncan swapmeet in March ... the only change is BIGGER ... the 2 north buildings are sold out and the building that was under construction last year is completed and will house an additional 100 plus...

On the right side of the car of the rear end, is there supposed to be a drain plug on the far end of the axle housing on the underside just before where the brake housing is riveted to the housing?

Working on getting some anti tarnish coverings made for my car and a few friends. May even make these to sell. So far we have worked out fitted headlight covers for 13 14 models (earlier models will come soon) hub cap covers and speedo covers. Pototyping of the rad and cowl lamps are progressing. All covers are made of water proof black canvas...

I know that I have seen one before, but I do not remember the name/maker. Any help would be appreciated.

head.jpeg

We are having our 9th annual Model T/ Model A/ prewar swap meet/ car show/ get together on Saturday April 18, 2026 at 700 A.M. at our farm. Free setup and admission. Outside spaces only. Bring your parts or cars to sell. [Model T's- Model A's or any makes pre 1945 or just come to visit. Everyone is welcome. Free primitive camping the night before....

My '26 speedster came with a low head. I have a high head in my stash. It looks like the high head has larger water jackets (better cooling?). What would your suggestions be on which would be best and why?

Thanks!

I am curious about the touring tops. Which years typically had the flaps on the back or was an aftermarket thing.

What is the Autolite spark plug number for 1/2 thread base plugs? I have seen three numbers: F11 , #25 , and 3095.

Dropped off a 1914 Windshield Frame along with the brass Glass Channel to mount it in. The shop calls me to inform that their Plate Glass is 3/16 thick however the Safety Glass is 1/4 thick. The option they gave is to have Plate Glass cut and then tempered however he also felt like that was against the law to use tempered in the Windshield...

Hello. I can't figure out some details about the seat assembly kit from Cubels for a 1915 Roadster. I would be grateful if some of you could help me with these questions:

1. See picture #1. Are the lower extensions of these seatback vertical posts supposed to sit on top of the seat riser cutout, as shown in the picture, or is it supposed to go...

I sourced this unit for a guy in India who has a 1915 T and wants to add a starter, but also wants everything period correct.
I got it from Dodge Riedy who got it to me here in Idaho a few days ago.
The bendix was completely stuck at first. After a bit of coaxing with penetrating oil, dunk tank and carb cleaner, I got the bendix working again....

This fabric item was between the front spring and the frame member on my ‘13. It appears to be long grain top material. The 1915 parts book shows an identical item, I’m wondering if anyone knows the purpose of the four small brass rivets ? IMG_3733.jpeg

Hey, can anyone in the group share the known measurements of the Model T transmission early Brake Drum Top-Hat bearing? I see some of them given by Benson Archives parts listing pages, but would prefer to have actual measurements, even if a little worn.

Thanks,

Jim Key
Accurate Models

brake drum 5B.jpg
brake drum 4.JPG

Hello there! Can I use red 50/50 OAT antifreeze in the 1927 model t?

Does anyone still make or have a set of steering unit tapers? Venders used to supply them but have not found any. Any ideas??
answer me here its quicker.
thnx,
frontyboy

Would like to communicate with anyone knowlegable with the late Model T (and early Model A) innertube valve stems:
Schrader 777, 888, 6300
Dill VS6, VS74 , VS 74, TR 16 VS 74, and VS-74A
Trying to understand the transition from Model T (wood spoke wheel), through the late Model T (wire spoke wheel), to the early Model A.

There are many events planned to commemorate the opening of Route 66 in 1926. Any clubs have plans? Here is a photo from 2012 for the worlds heaviest Model T in Tulsa. Commeration01b.jpg

IMG_5046.jpeg IMG_3004.jpeg IMG_4925.jpeg IMG_5071.jpeg

What do these fit? Are they for a 1925 Fordor?
IMG_5484.jpeg

I need twelve of the 1926-27 rear curtain fasteners for the open car top irons. The current offerings (RH) fit if you don’t try to sandwich the side curtains in between.

The Model A Roadster has snaps (LH) that fasten to the windshield with smaller holes. The Model A open cars also use the same side curtain fasteners on the body as do our Model...

Just a reminder that the annual old car swap meet in Marrietta, Ohio is Sat March 7th starting at 7:00 am. Lots of vendors with lots of model T and A stuff. Nice heated building with a nice lunch and pies and hot coffee. Vendors in attendance include Kevin Prus, David Nolting, Ron’s Machine Shop, The Carb Shed, The Coil Dr., with many individuals...

I'm trying to establish if the cam portion of my brake pedal is worn enough to warrant replacing the pedal. The pedal stroke seems to be too short, and so the band needs to be overly tightened to compensate, at least it seems that way.
The pedal supports are new reproduction parts.

Question: How much pedal free play can be considered within...

RE:

There is an interesting post in the Classifieds, and since myself, Steve, and a few others kinda hijacked John's ad, maybe it would be best to continue our discussions here.

So my next questions are; -in looking at pictures of Brad's (-and other's Boring Bar), it appears that the Engine Block's Cam bores become the 'datum' for aligning the...

With which a guy can set out for a club meeting, after dark, in February, with every expectation of a successful return hours later. Mid-'60s restoration, easy start on mag, and enough patina that sloppy roads are barely an inconvenience.

My kind of T.jpeg

Happy New Year's to all of you model t enthusiasts in or near Utah. A few of us are getting together for lunch on Saturday Jan 3rd at 1130 am at the Red Robbin in Murray Ut. Not planning to take my speedster this time as the weather looks to be not in favor of speedsters this week.
We're just hoping to meet a few other T people, talk about cars...

Does anyone have any experience with the Speedway Motors Windshield Frames for 26 Roadsters/Touring Cars? Do they match originals for look and fit?

This engine stand bracket (head unit) is of unknown manufacturer. Any ideas?

Have a new Rootlieb speedster kit with flat dashboard. I want to add a rounded sheet metal cowl. Looking for sheet metal cowl, or plans or patterns. I would buy a metal cowl, or a set of plans or drawings.

If you have made one I would like to know how you did it or who did it, any information would be helpful. Best to contact me here.

thnx,...

I picked this up a couple years ago and am just getting around to mess around with it now, someone has taken false cams off it and the boring bar has to be removed to install them back on, has anyone ever taken boring bar out?thanks 50C753A3-C37A-4BC8-BBE8-66D5B365E032.jpeg

Model T Speedster by Edsel Ford. 11/23/10. IMG_5063.jpeg

On the Top Support Irons that bolt to the Seat and support the Top Irons where the top pivots, how does the interior Upholstery wrap around this Support? Was it hand-stitched underneath, or ?? We are specifically working on a 1914 Touring, but any of the early open cars will likely be the same. Any pix??

TIA!!

Am I correct that this swivel is made In October 1919 and is a 6:1 ratio? If so would it be correct to use on a 1923 coupe?

On face book there is a gentleman that does metal spinning, I ask a question to him wondering if he could spin some replacement Bowls for the early Holley Carbs, hir reply was get me the dimensions. These would not be exactly like the originals and I know in the past someone was cutting the top off originals and silver soldering a new top (ring)....

I'm helping a friend with an original 36 Ford Sedan. He needs a new original type battery. I used to work at Ford Obsolete in Long Beach in my younger days, and as I recall the battery he needs is listed above. If those V8 boys are as picky as me, why can't he find the correct battery for his car?

Hi All ;
Can you tell me what are the best Magnet Clamps ?
Thank for your answer .
Toon 001.JPG

-7 this morning. Been - all week long. Too cold to really feel like working on T stuff. I hope it gets better. IMG_4608.jpeg

I am working on returning another barn fresh car to active duty but have struck a hurdle. No 1 cylinder was way down on compression. A bore scope revealed a set of original two piece valves, with well worn stems/guides, so off came the head. The valves were actually quite reasonable so the plan is to ream the guides to take new oversize stem one...

For half a century, members of the Rose City Model T Club have had access to Hand Cranked Coil Testers (HCCT) to tune up Model T coils. Nearly two decades ago, the club invested in a Strobo-Spark and it was a game changer. Today, the Electronically Cranked Coil Tester (ECCT) is available, which tests coils using dwell instead of amperage.

The...

Are all the e&j pat 1908 cowl and tail lamps the same size? I'm making the brass antitarnish covers and I need to know. I tried my covers on a 13 of a chapter friend and it fit fine just want to make sure be fore I post that it fits all patient 08 lamps when it might not. Thanks for the wisdom guys

I'm gathering parts to build a '26 roadster fuel delivery truck with my grandsons. I know many of you have all kinds of interesting things hidden away. I'm looking for a valve similar to this that would be used on a fuel delivery truck. Anyone out there have something similar they would be willing to part with?...

IMG_4996.jpeg IMG_4980.jpeg IMG_4979.jpeg IMG_4982.jpeg

I have a Muncie transmission that I am installing. I have the special joints and rebuilt it with new bearings, bushings, and idler shaft. I also have a bracket that looks like the one in the Muncie manual but I don’t have the “U” bolts and springs. From what I can seen in the manual illustrations, one bolt attaches the bracket to the bottom of the...

There is very little bushing to take the bite of a press tool.
I couldnt find the answer in past posts, so here it is.

I have removed with a modified flat washer, ground on the sides to an oval shape & the outer edges sharpened to just fit in the gap between the drum lip & the bushing. Angel into place as a device to catch the bushing to be able...

I was wondering if someone could post a photo of the diamond graphic on this type of coil. This one isn’t clear enough for me to read everything, and I was just curious what a good one looks like. Thank you.
IMG_7929.png IMG_7930.png IMG_7931.png

I know this is going to be difficult since most people won't have experience with using both types for a true comparison, but since I need to get onto the waiting list for either of those two 30x3½ Clincher White tires, I gotta make a decision. So, between these two brands of tires, which tire will last longer mileage wise? The Ribbed Universal...

That time of year again!

Jan 16-17 2026 will be our schedule days!!

We have a block of rooms available at a discount of $99 a night at Hampton Inn in McPherson Kansas. Cut off to get your discounted room date is Dec 26th so book fast!

Can’t wait to see old and new faces!

Aaron Frazer

Hotel information:

200 N Centennial Dr
McPherson, KS...

Any out there?..For the Presto automobile heater….used on the intake manifold, my picture won’t upload

Will the Float-A-Ford system fit on an over the axle wishbone front axle, and also is there a source for the 2 different spring sizes? I would like to install them on my '11 Torpedo.
Thank you in advance for any info forthcoming.

regards,
Bruce

I know this is not a T topic, but I was wondering if Moreland Trucks were made up to WWII?

IMG_3697.jpeg

Seems like the restorer’s dilemma has been with us since the early days ! :lol: (cartoon from 1920)

You can buy a restored car for less than it costs to restore one !

IMG_4951.jpeg IMG_4968.jpeg IMG_4952.jpeg IMG_4842.jpeg

Leaning left is not only my politics, it's also an issue with my 1915/16 runabout. The right side fenders (front and rear) measure 3 higher than the left side. It's been this way since I bought it 5 years ago and it hasn't really bothered me but I'd like to straighten it up. Any suggestions?

I needed to take the pan off a engine built (too) many years ago to check things and get it ready for installing my Rajo BB head. In the process, I mangled the new style crank seal I had installed. I have both felt seals and a new style seal that I could install. Can’t make up my mind which to use. The new one would probably seal better, but seems...

So we haven't made it out of the single digits in a week and a half, if you're feeling some cabin fever set in, I have something for you. We're opening up the bodyshop again this Saturday for anyone in the south east side of Wi. The swapmeet starts at 9 am, goes till noon. Last year we had 10-12 venders, and they brought alot of material. Then...

AHOOGA 6v motor speed? Like, what RPM does the motor turn? I'm thinking of getting a cheap 12v AHOOGA and then replacing the motor.

Right now on AACA parts for sale are some 14 mm Take apart plugs for sale. Not mine just passing the info.