This guy had great results with this product.
These instructions are for a Model A but the procedure about how to flush the tank should be the same.
I am not sure if you can use the mentioned product more than once.
FJ
Removing Rust From A Gas Tank
Forum rules
If you need help logging in, or have question about how something works, use the Support forum located here Support Forum
Complete set of Forum Rules Forum Rules
If you need help logging in, or have question about how something works, use the Support forum located here Support Forum
Complete set of Forum Rules Forum Rules
-
Topic author - Posts: 1724
- Joined: Sun Jan 06, 2019 10:50 am
- First Name: James
- Last Name: Jarzabek
- Location: Dayton, OH
- MTFCA Number: 29562
- MTFCI Number: 24398
- Board Member Since: 2008
- Contact:
-
- Posts: 1278
- Joined: Sun Jan 06, 2019 7:00 pm
- First Name: Mack
- Last Name: Cole
- * REQUIRED* Type and Year of Model Ts owned: TT. T express pickup,speedster project.
- Location: North Carolina
- MTFCA Number: 28146
Re: Removing Rust From A Gas Tank
https://www.ebay.com/itm/Rust911-UltraC ... 2f348e7d35
Um,may be a viable alternative to sandblasting and such for alot of parts.I think I read something about the 16 gallons would clean 600 pounds of metal?
I don't have much knowledge of chemistry. But lets say i wanted to clean the lock rings for a TT rim, would this chemical be safe as far not affecting the metal? What about springs? I guess you could put some in a plastic pan and turn a T engine block upside down in the tub over night and clean the water passages really well.Might even help unstick parts like the valves and pistons on a rougher block?
The possiablitys are endless if it won't hur the metal. I would think maby check to see if babbit is another concern?
Um,may be a viable alternative to sandblasting and such for alot of parts.I think I read something about the 16 gallons would clean 600 pounds of metal?
I don't have much knowledge of chemistry. But lets say i wanted to clean the lock rings for a TT rim, would this chemical be safe as far not affecting the metal? What about springs? I guess you could put some in a plastic pan and turn a T engine block upside down in the tub over night and clean the water passages really well.Might even help unstick parts like the valves and pistons on a rougher block?
The possiablitys are endless if it won't hur the metal. I would think maby check to see if babbit is another concern?
If you can't help em, don't hinder em'
-
- Posts: 353
- Joined: Sun Jan 06, 2019 10:29 pm
- First Name: Richard
- Last Name: Grzegorowicz
- * REQUIRED* Type and Year of Model Ts owned: 1921 T pickup
- Location: Hartland VT
Re: Removing Rust From A Gas Tank
BE CAREFUL, HAVING,WORKED ON MORE THAN A FEW A-FORDS, UP HERE IN THE HILLS THEY GOT THE CRAP BEAT OUT OF THEM, AND STILL THEY COME BACK FOR MORE, THE MODEL A STEERING WHEEL POST IS CONNECTED TO THE GAS TANK , INSPECT THIS VERY CLOSE, I HAVE SEEN TWO THAT LEAKED THERE BECAUSE OF RUST MAKING THIS SPOT VERY THIN. THE TANK YOU SPEAK OF HAS HAD A HARD LIFE I WOULD SAY. THERE USED TO BE A PRODUCT CALLED SLOSH THIS WOULD COAT THE INSIDE AFTER CLEANING, IT WORKED BUT AFTER A WHILE IF WOULD FLAKE OFF AND PLUG THE FILTER. SNAP ON MADE A CAMERA ON THE END OF A LONG FLEX PIPE, YOU COULD PEEK IN FOR A LOOK SEE. GOOD LUCK
-
- Posts: 1011
- Joined: Mon Jan 07, 2019 10:18 pm
- First Name: Mark
- Last Name: Osterman
- * REQUIRED* Type and Year of Model Ts owned: 1923 runabout
- Location: Rochester, NY
- Contact:
Re: Removing Rust From A Gas Tank
I plugged the bottom of my original tank and then poured in about 5 lbs of bbs. Then poured in hot water and detergent. I capped the tank and rolled it around for about 45 mins. Then I emptied the tank and rinsed with several changes of water followed by a gallon of 95% grain alcohol and allowed to dry. Then I sprayed a little kerosene in there since it would have been a few days before I installed it and filled with gas. Have never had any trouble since installation.