TT Truck Part Identification
Forum rules
If you need help logging in, or have question about how something works, use the Support forum located here Support Forum
Complete set of Forum Rules Forum Rules
If you need help logging in, or have question about how something works, use the Support forum located here Support Forum
Complete set of Forum Rules Forum Rules
-
Topic author - Posts: 3346
- Joined: Sat Jan 12, 2019 12:11 pm
- First Name: Mark
- Last Name: Chaffin
- * REQUIRED* Type and Year of Model Ts owned: 1911 Speedster, 1927 Lake Roadster
- Location: Lake Elsinore
- MTFCA Number: 31705
- Board Member Since: 2001
TT Truck Part Identification
Okay you TT Truck guys. Need some help identifying this part. Any help would be appreciated. It appears to be a bushing or collar. The OD is approximately 1 1/4". The ID is approximately 1".
-
- Posts: 490
- Joined: Sun Jan 06, 2019 11:14 am
- First Name: Henry
- Last Name: Petrino
- * REQUIRED* Type and Year of Model Ts owned: 1918 TT
- Location: Modesto, CA
Re: TT Truck Part Identification
I'm not 100% on this, but I think it's a rear spring perch bushing.
-
- Posts: 118
- Joined: Sun Jan 06, 2019 6:44 pm
- First Name: Rich
- Last Name: Chillingworth
- * REQUIRED* Type and Year of Model Ts owned: 1924 C-Cab TT
- Location: Tulsa, OK
- MTFCA Number: 30527
- MTFCI Number: 23207
Re: TT Truck Part Identification
Mark, your piece is from an early TT rear spring perch. Those early perches had a narrow casting with a collar on each end to make up the width. Later, the perch castings were full length and didn't have the collars anymore. This picture is not the best, but it shows where your collar sits.
Rich C.-
- Posts: 27
- Joined: Sun Jan 06, 2019 4:54 pm
- First Name: Bruce
- Last Name: Hopkins
- * REQUIRED* Type and Year of Model Ts owned: 11 Torpedo, 20TT 1Ton, 27 Runabout
- Location: Victoria BC Canada
Re: TT Truck Part Identification
spacer for rear spring shackle that goes on housing perch
-
Topic author - Posts: 3346
- Joined: Sat Jan 12, 2019 12:11 pm
- First Name: Mark
- Last Name: Chaffin
- * REQUIRED* Type and Year of Model Ts owned: 1911 Speedster, 1927 Lake Roadster
- Location: Lake Elsinore
- MTFCA Number: 31705
- Board Member Since: 2001
Re: TT Truck Part Identification
No. I don't think so. The spring perch bushing measures 1.00" OD and .700 ID. Thanks for the input though.
-
Topic author - Posts: 3346
- Joined: Sat Jan 12, 2019 12:11 pm
- First Name: Mark
- Last Name: Chaffin
- * REQUIRED* Type and Year of Model Ts owned: 1911 Speedster, 1927 Lake Roadster
- Location: Lake Elsinore
- MTFCA Number: 31705
- Board Member Since: 2001
Re: TT Truck Part Identification
I think you are correct Rich! The TT spring perch bushings I have (later) fit the inside diameter of the part pictured (collar).
-
Topic author - Posts: 3346
- Joined: Sat Jan 12, 2019 12:11 pm
- First Name: Mark
- Last Name: Chaffin
- * REQUIRED* Type and Year of Model Ts owned: 1911 Speedster, 1927 Lake Roadster
- Location: Lake Elsinore
- MTFCA Number: 31705
- Board Member Since: 2001
Re: TT Truck Part Identification
So, would this part be considered an "early TT rear spring perch collar"?
-
- Posts: 3384
- Joined: Sun Jan 06, 2019 11:39 am
- First Name: Tim
- Last Name: Morsher
- * REQUIRED* Type and Year of Model Ts owned: 1925TT, 1926 Martin-Parry bodied wagon, 1927 mercury bodied speedster
- Location: Norwalk Ohio
Re: TT Truck Part Identification
Learn something new everyday ! I have a bunch of these, and always just used them to make split flexible collar clamps for magneto drives. They are perfect for that.
-
- Posts: 490
- Joined: Sun Jan 06, 2019 11:14 am
- First Name: Henry
- Last Name: Petrino
- * REQUIRED* Type and Year of Model Ts owned: 1918 TT
- Location: Modesto, CA
Re: TT Truck Part Identification
My '18 TT is parked at my sons place 45 miles away, so I can't go look at it right now. However, as soon as Rick correctly identified it I remembered them on my truck. I remembered at the time when I had it apart (nearly 20 years ago) wondering why Ford didn't just make the casting a little bigger, which apparently was done later.