Guardian Angel Found the issue!

Discuss all things Model T related.
Forum rules
If you need help logging in, or have question about how something works, use the Support forum located here Support Forum
Complete set of Forum Rules Forum Rules

Topic author
Mustang1964s
Posts: 254
Joined: Sun Jan 06, 2019 10:48 pm
First Name: Steve
Last Name: Bourgeois
* REQUIRED* Type and Year of Model Ts owned: 1914, 1926
Location: Waco, TX
MTFCA Number: 29784
MTFCI Number: 22970
Board Member Since: 2007

Guardian Angel Found the issue!

Post by Mustang1964s » Mon Sep 21, 2020 9:53 am

I had never really believed in a guardian angel until the events of this past weekend.

We have an old/new T in the garage, and I was trying to get it ready for the road.

After several attempts of getting her around the block. I was able to take her on a three-mile loop around the neighborhood. Got back to the house and the youngest grandson was itching for a ride. Sure, one more time around the loop would be great for him and the car. We had just made it past the first right turn then the T just died. DEAD. No lights, no starter, nothing. I pushed it back a little bit to a neighbor’s driveway. Then did a hard-right turn. Just like the one that we would have encountered at the next turn. Then SNAP something broke. The steering wheel would just spin, the wheels stayed put. I had the grandson jump and run get his brothers to help push it back in to the garage. I had been working on the electrical system off and on for some time. I was just miffed at the car, or more at myself. After the T was back in its place, I started to determine what happened. The positive lead popped off. I had tightened it. Then just left it and turned my attention to the other T. Later that night, I just started to think about the events and why the T just stopped and what could have broken in the steering. Then it hit me that I am thank full for the cable coming loose and killing the T. Just imaging what would happen if we had taken the corner and the steering had broken in mid turn. It would have not ended well. As it turns out the guardian angle saved our bacon. I still have not figured out the steering issue, that will be one evening this week. Don’t know if the T or my grandson has the angle. My bet is the grandson. He had so many health issues it is a miracle that he is here. God has a plan for him. I hope I am around to see what the plan is.
Last edited by Mustang1964s on Mon Sep 21, 2020 7:07 pm, edited 1 time in total.

User avatar

TWrenn
Posts: 3388
Joined: Sun Jan 06, 2019 10:53 am
First Name: Tim
Last Name: Wrenn
* REQUIRED* Type and Year of Model Ts owned: '13 Touring, '26 "Overlap" Fordor
Location: Ohio
MTFCA Number: 30701
MTFCI Number: 24033
Board Member Since: 2019

Re: Guardian Angel

Post by TWrenn » Mon Sep 21, 2020 10:13 am

Wow. I'm glad you guys had that angel with you!

There's not much to the steering system. Whatever broke will show up pretty quick. Start underneath and work your way up.
Could be something hidden under the steering wheel in that gearbox, but I bet it's something down below.

Good luck. God blessed you!

User avatar

John iaccino
Posts: 746
Joined: Mon Jan 07, 2019 5:25 am
First Name: John
Last Name: Iaccino
* REQUIRED* Type and Year of Model Ts owned: 1911 Roadster, Open Runnabout
Location: Rhinebeck, NY
MTFCA Number: 17802

Re: Guardian Angel

Post by John iaccino » Mon Sep 21, 2020 10:41 am

Check the keyway down where the pitman arm is attached.


Topic author
Mustang1964s
Posts: 254
Joined: Sun Jan 06, 2019 10:48 pm
First Name: Steve
Last Name: Bourgeois
* REQUIRED* Type and Year of Model Ts owned: 1914, 1926
Location: Waco, TX
MTFCA Number: 29784
MTFCI Number: 22970
Board Member Since: 2007

Re: Guardian Angel

Post by Mustang1964s » Mon Sep 21, 2020 10:46 am

Yes. I will inspect the steering from wheel to wheel.


Norman Kling
Posts: 4068
Joined: Tue Jan 08, 2019 1:39 pm
First Name: Norman
Last Name: Kling
Location: Alpine California

Re: Guardian Angel

Post by Norman Kling » Mon Sep 21, 2020 11:02 am

Wow!!
Norm

User avatar

FreighTer Jim
Posts: 1724
Joined: Sun Jan 06, 2019 10:50 am
First Name: James
Last Name: Jarzabek
Location: Dayton, OH
MTFCA Number: 29562
MTFCI Number: 24398
Board Member Since: 2008
Contact:

Re: Guardian Angel

Post by FreighTer Jim » Mon Sep 21, 2020 11:09 am

Steve

I call that “ The Best Bad Luck “ 🍀

Happens to me all the time 👍


FJ
Google “ Model T Transport “
MTFCA - MTFCI - MAFCA Member

User avatar

RustyFords
Posts: 1554
Joined: Sun Jan 06, 2019 11:16 am
First Name: Don
Last Name: Allen
* REQUIRED* Type and Year of Model Ts owned: 1924 Touring
Location: Houston, TX
MTFCA Number: 50001

Re: Guardian Angel

Post by RustyFords » Mon Sep 21, 2020 11:33 am

My angel quit a while back, citing exhaustion. The new guy has already put in for a transfer.
1924 Touring


Topic author
Mustang1964s
Posts: 254
Joined: Sun Jan 06, 2019 10:48 pm
First Name: Steve
Last Name: Bourgeois
* REQUIRED* Type and Year of Model Ts owned: 1914, 1926
Location: Waco, TX
MTFCA Number: 29784
MTFCI Number: 22970
Board Member Since: 2007

Re: Guardian Angel

Post by Mustang1964s » Mon Sep 21, 2020 7:06 pm

Found the steering issue. Dodged a bullet.
I thought the steering columns were solid.
IMG_2503.jpg
Now to find a good straight column.


George Hand
Posts: 305
Joined: Sun Jan 06, 2019 12:02 pm
First Name: George
Last Name: Hand
* REQUIRED* Type and Year of Model Ts owned: 1912 open express, 1920 touring, 1926 tudor-lisenced and insured, 1921tt project 1922 fendered chassis, 192x tt dootle bug 192xengine w/winch projects
Location: Preble NY
MTFCA Number: 28114
MTFCI Number: 21834

Re: Guardian Angel Found the issue!

Post by George Hand » Mon Sep 21, 2020 7:20 pm

Steve, Looks like it has been cracked for awhile, my guess would be excessive up & down steering column due to a week firewall at the column mounting. By the way I gather you have an early Mustang(s). I have a NY Rusty 6cyl. convertible warranty plate data date July 25th.


Stephen_heatherly
Posts: 364
Joined: Wed Jan 09, 2019 6:03 pm
First Name: Stephen
Last Name: Heatherly
* REQUIRED* Type and Year of Model Ts owned: 26 coupe and 23 Runabout
Location: St. Louis MO

Re: Guardian Angel Found the issue!

Post by Stephen_heatherly » Mon Sep 21, 2020 7:35 pm

I honestly never would have thought that something like that could happen. I'm glad both you and your grandson are safe. This is a good reminder that these cars need to be thoroughly checked out and repaired before any serious driving can be done. I've had some big surprises what was damaged and worn out when restoring my own cars.

Stephen


John kuehn
Posts: 3907
Joined: Sun Jan 06, 2019 8:00 pm
First Name: John
Last Name: Kuehn
* REQUIRED* Type and Year of Model Ts owned: 19 Roadster, 21 Touring, 24 Coupe
Location: Texas
MTFCA Number: 28924

Re: Guardian Angel Found the issue!

Post by John kuehn » Mon Sep 21, 2020 7:49 pm

Surely the steering column isn’t a piece of tubing! Hopefully at least it was the standard solid
column. But I would never thought a steering column would twist in to like that. The ones I have found in junk yards and farm auctions were used as pry bars, chisels and no telling what but for a break like that I have to say WOW like Norm said!
That copper color sure looks like a piece of hard drawn copper tubing but surely not!

User avatar

RajoRacer
Posts: 4305
Joined: Sun Jan 06, 2019 12:18 pm
First Name: Steve
Last Name: Tomaso
* REQUIRED* Type and Year of Model Ts owned: 1914 Touring, 1919 Centerdoor, 1924 TT C-Cab Express, 1925 Racer
Location: Longbranch, WA
MTFCA Number: 14972
MTFCI Number: 15411
Board Member Since: 2001

Re: Guardian Angel Found the issue!

Post by RajoRacer » Mon Sep 21, 2020 7:53 pm

Not a "FORD" steering shaft ! They are solid 3/4" steel - I just cut one to make a pry bar.


Jerry VanOoteghem
Posts: 2948
Joined: Sun Jan 06, 2019 4:06 pm
First Name: Jerry
Last Name: Van
Location: S.E. Michigan
MTFCA Number: 24868

Re: Guardian Angel Found the issue!

Post by Jerry VanOoteghem » Mon Sep 21, 2020 7:53 pm

WOW! I'm shocked. I too always believed these were solid!

I also had a guardian angel watching over me. Driving my T down a hilly country road, I made a left hand turn. Proceeded about 1/2 mile and just after topping a nice hill, I realized I made a wrong turn. Seconds after pulling into a driveway to turn around, a Ford Explorer topped that hill at maybe 100 mph, all 4 wheels off the ground. Had I not pulled into that driveway, I'd now be one of your guardian angels myself, (I would hope so anyway). I can think of at least 3 other miraculously timed T failures that happened to others. (Henry? Is that you???) :shock:


George Hand
Posts: 305
Joined: Sun Jan 06, 2019 12:02 pm
First Name: George
Last Name: Hand
* REQUIRED* Type and Year of Model Ts owned: 1912 open express, 1920 touring, 1926 tudor-lisenced and insured, 1921tt project 1922 fendered chassis, 192x tt dootle bug 192xengine w/winch projects
Location: Preble NY
MTFCA Number: 28114
MTFCI Number: 21834

Re: Guardian Angel Found the issue!

Post by George Hand » Mon Sep 21, 2020 8:10 pm

Solid shaft? Maybe the early ones by the look of the throttle lever this car has a Vaporizer Carburetor which would make it from a later '26-7. The wood firewall tells me it has a aftermarket body & not as supported as it was when it would have been in the "Original" car with a metal firewall & column support. My guess old "Henry" always looking to save on the vehicle cost had hollow shafts in the late vehicles. George


Scott_Conger
Posts: 6428
Joined: Sun Jan 06, 2019 11:18 am
First Name: Scott
Last Name: Conger
* REQUIRED* Type and Year of Model Ts owned: '13, '15, '19, '23
Location: Clark, WY
Board Member Since: 2005

Re: Guardian Angel Found the issue!

Post by Scott_Conger » Mon Sep 21, 2020 9:02 pm

Non-original
Scott Conger

Tyranny under the guise of law is still Tyranny

NH Full Flow Float Valves
Obsolete carburetor parts manufactured

User avatar

Humblej
Posts: 1690
Joined: Sun Jan 06, 2019 12:23 pm
First Name: Jeff
Last Name: Humble
* REQUIRED* Type and Year of Model Ts owned: 1926 Canadian built coupe, 1924 TT C-cab, survivor 1924 roadster
Location: Charlevoix, Mi
MTFCA Number: 28034
Board Member Since: 2006

Re: Guardian Angel Found the issue!

Post by Humblej » Mon Sep 21, 2020 9:34 pm

Looks like a copper tube to me too. Yikes! Wounder what else is lurking out of sight.


Wayne Sheldon
Posts: 3637
Joined: Sun Jan 06, 2019 3:13 pm
First Name: Wayne
Last Name: Sheldon
* REQUIRED* Type and Year of Model Ts owned: 1915 Runabout 1913 Speedster
Location: Grass Valley California, USA
Board Member Since: 2005

Re: Guardian Angel Found the issue!

Post by Wayne Sheldon » Mon Sep 21, 2020 10:25 pm

I think antique automobiles have guardian angels. Given everything else in my life, I am sure I do not have one.
But the model Ts? In one T, I sheared the pinion gear key in my driveway. I missed that Endurance Run, but I was okay with that when I thought of the places I was expecting to be that it could have broken. Another T race car broke the tie rod in my driveway, the day before the Endurance Run (different car, a few years earlier). That time I was able to replace it and make the run. That could have been a lot worse considering sudden steering loss at racer speeds. There have been many times I and others I know have had potentially dangerous breaks at the most perfect time and place.

I hope I didn't upset the angels by telling these tales.


Dan Hatch
Posts: 4110
Joined: Tue Jan 08, 2019 7:31 pm
First Name: Dan
Last Name: Hatch
Location: Alabama
MTFCA Number: 49974

Re: Guardian Angel Found the issue!

Post by Dan Hatch » Tue Sep 22, 2020 2:33 am

Looks like pins holding that gas lever are copper wire too. Better check everything on that car before you go far.


Allan
Posts: 5201
Joined: Sun Jan 06, 2019 7:21 pm
First Name: Allan
Last Name: Bennett
* REQUIRED* Type and Year of Model Ts owned: 1912 van, 1917 shooting brake, 1929 roadster buckboard, 1924 tourer, 1925 barn find buckboard, 1925 D &F wide body roadster, 1927LHD Tudor sedan.
Location: Gawler, Australia

Re: Guardian Angel Found the issue!

Post by Allan » Tue Sep 22, 2020 3:45 am

On close inspection I think it was welded together at that point, and the weld has let go. It certainly is not a standard Ford shaft. The weld may ave been filed back into round, thereby further reducing its strength. I believe the copper colour is red primer. Under where the paint is buffed off it shows bare steel. The weld too is broken steel. It looks like the throttle arm is held in place with two cotter pins. All in all, I would be checking everything on that restoration. If that sort of work is done on steering components, I seriously distrust the standard of workmanship.
The angels have served you well.

Allan from own under.


D Stroud
Posts: 1015
Joined: Sun Jan 06, 2019 10:45 am
First Name: David
Last Name: Stroud
* REQUIRED* Type and Year of Model Ts owned: 1925 Coupe
Location: Mound City, MO 64470
Board Member Since: 2011

Re: Guardian Angel Found the issue!

Post by D Stroud » Tue Sep 22, 2020 4:43 am

George H., as frugal as Henry was, he never made hollow steering shafts, which are not columns. A column is what the shafts are enclosed in.
We need more pictures of that shaft, there is something seriously wrong going on here. Clean everything up and take several more pictures. That looks very scary, hope nothing else was repaired that way. JMHO Dave
1925 mostly original coupe.


D Stroud
Posts: 1015
Joined: Sun Jan 06, 2019 10:45 am
First Name: David
Last Name: Stroud
* REQUIRED* Type and Year of Model Ts owned: 1925 Coupe
Location: Mound City, MO 64470
Board Member Since: 2011

Re: Guardian Angel Found the issue!

Post by D Stroud » Tue Sep 22, 2020 5:22 am

As an afterthought, I have made most of my living for the past 40+ years as a welder. As experienced as I am, I would never weld two pieces of a steering shaft together on something that would be driven. I have seen many shafts, not just steering shafts, welded together with just a small bevel on each end, and then the weld was ground down to fit whatever, leaving very little "meat" to hold the joint. Several years ago, there were some posts on the old forum about some reproduction early '09 type front axle "yokes" that were made to weld on later axles to convert them to the earlier style. Apparently, the ends of the axle and the ends of the repro "yokes" were just beveld a bit and welded on. Then, a lot of the weld was ground off to look "original", leaving very little "meat" for strength, causing some accidents when the ends broke off. Anything like that should be beveled enough to get at least a 100% weld, anything less is just asking for trouble. As for the steering shaft that has been shown, beveling both ends to get a 100% weld would be much better, but I wouldn't trust it without some close inspection periodically. JMHO. Dave
1925 mostly original coupe.

User avatar

George House
Posts: 2270
Joined: Sun Jan 06, 2019 5:25 pm
First Name: George
Last Name: House
* REQUIRED* Type and Year of Model Ts owned: ‘10 Maxwell AA, ‘11Hupp Model 20, Two 1914 Ford runabouts, 19 centerdoor, 25 C Cab,26 roadster
Location: Northern Caldwell County TX
MTFCA Number: 115
MTFCA Life Member: YES
Board Member Since: 1999

Re: Guardian Angel Found the issue!

Post by George House » Tue Sep 22, 2020 6:55 am

Steve,
You ever get south around Caldwell County TX ? If so, I’ll give you a good steering column...
I don’t know why I turned out this way. My parents were decent people 🤪


Topic author
Mustang1964s
Posts: 254
Joined: Sun Jan 06, 2019 10:48 pm
First Name: Steve
Last Name: Bourgeois
* REQUIRED* Type and Year of Model Ts owned: 1914, 1926
Location: Waco, TX
MTFCA Number: 29784
MTFCI Number: 22970
Board Member Since: 2007

Re: Guardian Angel Found the issue!

Post by Mustang1964s » Tue Sep 22, 2020 8:26 am

George, You're just a couple of hours south of me.
I will PM you to make arrangements.

User avatar

John Warren
Posts: 1069
Joined: Sun Jan 06, 2019 12:18 pm
First Name: John
Last Name: Warren
* REQUIRED* Type and Year of Model Ts owned: 14 Roadster, 25 Pickup , 26 Canadian Touring , and a 24-28 TA race car
Location: Henderson, Nevada

Re: Guardian Angel Found the issue!

Post by John Warren » Tue Sep 22, 2020 8:33 am

Yes, there was an intervention, Thank God. Something similar happened to me and my friend. We had a desert buggy that we built at a young age. Out on a run in the hills, the steering drag link broke just after we had made a fast hard left turn next a deep ravine. We just had straightened out and slowed down and it broke, had it broke earlier....? Just doesn't hurt anything to believe. As many have said, NOT a ford steering shaft. Good luck and have fun with the kids and the car.
24-28 TA race car, 26 Canadian touring, 25 Roadster pickup, 14 Roadster, and 11AB Maxwell runabout
Keep it simple and keep a good junk pile if you want to invent something :P


Topic author
Mustang1964s
Posts: 254
Joined: Sun Jan 06, 2019 10:48 pm
First Name: Steve
Last Name: Bourgeois
* REQUIRED* Type and Year of Model Ts owned: 1914, 1926
Location: Waco, TX
MTFCA Number: 29784
MTFCI Number: 22970
Board Member Since: 2007

Re: Guardian Angel Found the issue!

Post by Mustang1964s » Tue Sep 22, 2020 7:36 pm

I was able to pull the top half of the steering column out.
It does not look like it's hollow.
Still does not look like one piece of solid steel.
IMG_2504.jpg


Jerry VanOoteghem
Posts: 2948
Joined: Sun Jan 06, 2019 4:06 pm
First Name: Jerry
Last Name: Van
Location: S.E. Michigan
MTFCA Number: 24868

Re: Guardian Angel Found the issue!

Post by Jerry VanOoteghem » Tue Sep 22, 2020 8:09 pm

Somebody welded two pieces together... and very poorly. Why do people do stuff like this.......

User avatar

DanTreace
Posts: 3299
Joined: Sun Jan 06, 2019 10:56 am
First Name: Dan
Last Name: Treace
* REQUIRED* Type and Year of Model Ts owned: '23 cutoff, '25 touring, '27 touring
Location: North Central FL
MTFCA Number: 4838
MTFCI Number: 115
Board Member Since: 2000
Contact:

Re: Guardian Angel Found the issue!

Post by DanTreace » Tue Sep 22, 2020 8:16 pm

That is what is seems, perhaps the builder wanted to shorten or lengthen a Ford steering post, and drilled part way into each piece. Placed a steel rod to act as a dowel, then welded up around the joint. Rather risky for a steering post shaft.
The best way is always the simplest. The attics of the world are cluttered up with complicated failures. Henry Ford
Don’t find fault, find a remedy; anybody can complain. Henry Ford


Allan
Posts: 5201
Joined: Sun Jan 06, 2019 7:21 pm
First Name: Allan
Last Name: Bennett
* REQUIRED* Type and Year of Model Ts owned: 1912 van, 1917 shooting brake, 1929 roadster buckboard, 1924 tourer, 1925 barn find buckboard, 1925 D &F wide body roadster, 1927LHD Tudor sedan.
Location: Gawler, Australia

Re: Guardian Angel Found the issue!

Post by Allan » Wed Sep 23, 2020 12:00 am

Had the 'dowel' been of smaller diameter, had both sides of the shaft been deeply V'ed, had the weld been made deep enough to pick up the dowel too, then that break may not have happened. But, it is still a modified, welded steering component, which should be avoided. That it was done in such a manner raises alarm bells about the way other work may have been done.

Allan from down under.


W Austen
Posts: 95
Joined: Mon Jan 07, 2019 5:42 pm
First Name: Bill
Last Name: Austen
* REQUIRED* Type and Year of Model Ts owned: 1915
Location: CA

Re: Guardian Angel Found the issue!

Post by W Austen » Wed Sep 23, 2020 12:22 am

Years ago when Ed Towe was putting together his Ford collection he purchased a 1909 from a guy that had been in the process of restoring it. The car looked good and Ed thought it was finished . Well one day Ed went to drive the car around a parking lot and he lost all steering. The previous owner couldn't find an original short 09 steering shaft so he took a later one, cut it , drilled and tapped one side , and machined and threaded the other side so it would screw together making it the right length . It unscrewed, Ed called the guy and was told "Oh I must of forgot to pin and weld it" Lew Rector fixed it.


Norman Kling
Posts: 4068
Joined: Tue Jan 08, 2019 1:39 pm
First Name: Norman
Last Name: Kling
Location: Alpine California

Re: Guardian Angel Found the issue!

Post by Norman Kling » Wed Sep 23, 2020 11:16 am

I had something similar happen on my first tour with the San Diego Model T club. I had purchased a 1926 Roadster. I had trouble with the low band so, while I had it apart to replace the bands, I also installed Rocky Mountain brakes, because I live in the mountains. This work had been done before the tour. On the way home from the tour, twilight was just beginning and I wondered if I would need to turn on the lights to go the last 15 miles home. I had stopped for a red light and when it turned green, I pushed the low pedal and there was a BANG. I was in free wheeling. So I had to call someone to come get us. I didn't need to use the lights! I was able to push the car into a parking lot and came to get it the next day. If not for the auxiliary brakes, and if it had happened on a hill, it could have been a disaster.
It turned out that someone had welded the driveshaft about 10 inches in front of the pinion gear. And as in the above situation, only welded around the outside.
So this can apply to any shaft in the car perhaps even to the rear axles.
Norm


Mikey1968
Posts: 229
Joined: Fri Mar 01, 2019 9:08 am
First Name: Michael
Last Name: Jewell
* REQUIRED* Type and Year of Model Ts owned: 1926 Touring
Location: Northern Virginia

Re: Guardian Angel Found the issue!

Post by Mikey1968 » Wed Sep 23, 2020 12:49 pm

We have 9 cars so many sit for awhile. One day I decided to take the 74 Bronco out. Our driveway is 200-300 feet of gravel. Got halfway when the Bronco no longer moved. Weird. I could rev the engine and speedo was showing a nice high speed but I wasn't moving. I looked at the driveshaft and it was spinning, alright. So I figured I shelled the rear gears. So, I figured I'd just lock the hubs and shift in the front wheels but the silly hubs were a bit rusty and sticking. So I got out again and looked under to see if I could see anything around the rear gears. Then, I noticed I could see my rear brake shoes on one side with the drum on the outside of it....the tire was jammed up against the fender (uncut rear fenders). Yup, the axle bearing and retaining ring had broken free on the axle and out came the axle, drum and wheel.

I just left it in the driveway until the new axles, bearing and retainers came in and jacked it up right where it stopped and repaired the one side, drove it back into the garage and swapped in the other set.

Imagine if this happened at speed! :shock: On a lesser note, what if the front hubs locked and I tried to drive it the short way back into the garage?

Post Reply Previous topicNext topic