Need some help

Discuss all things Model T related.
Forum rules
If you need help logging in, or have question about how something works, use the Support forum located here Support Forum
Complete set of Forum Rules Forum Rules

Topic author
John L
Posts: 124
Joined: Sun Jan 06, 2019 2:39 pm
First Name: John
Last Name: Leffler
* REQUIRED* Type and Year of Model Ts owned: 1923 Coupe, 1927 Touring
Location: Lebanon PA 17046
MTFCA Number: 22526

Need some help

Post by John L » Fri Jun 18, 2021 8:16 am

While driving the 1923 Coupe. Everything was fine until I pulled out at the red light .I pushed the couch in and nothing.I got home on a trailer. I released the brake lever all the forward, and I could push the car back and forth no resistance. I thought a broken u joint. I pulled the rear and everything looks fine so I thought the transmission. I took the trans cover off, everything looks fine. And then looking at the back of the transmission where the square slot for the driveshaft fits in turns with brake lever all the way forward and cranking it by hand. What can I check next?


mtntee20
Posts: 527
Joined: Sun Jan 06, 2019 2:51 pm
First Name: Terry & Sharon
Last Name: Miller
* REQUIRED* Type and Year of Model Ts owned: 1920 Center Door, 1920 TTWood cab Farm Truck with cable dump grain bed, 1920 TT C-Cab with express bed, 1927 Wood body Dairy Delivery truck
Location: Westminster, CO
MTFCA Number: 32583
Board Member Since: 2017

Re: Need some help

Post by mtntee20 » Fri Jun 18, 2021 8:38 am

John,

A couple of ideas: You stated you "pulled the rear". Does that mean you open up the differential? My first thought was failed babbitt thrust washer in the differential. My second thought is broken axle. Along this line of thinking, maybe a failed axle key at the wheel hub(s).

If you can turn the drive line when cranking the engine, the problem would appear to be in the rear end.

Good Luck,
Terry


Allan
Posts: 5201
Joined: Sun Jan 06, 2019 7:21 pm
First Name: Allan
Last Name: Bennett
* REQUIRED* Type and Year of Model Ts owned: 1912 van, 1917 shooting brake, 1929 roadster buckboard, 1924 tourer, 1925 barn find buckboard, 1925 D &F wide body roadster, 1927LHD Tudor sedan.
Location: Gawler, Australia

Re: Need some help

Post by Allan » Fri Jun 18, 2021 8:46 am

I had the same symptoms. It was a broken axle. happened as I put the pedal down to cross an intersection. Click! No progress.

Allan from down under.

User avatar

CudaMan
Posts: 2385
Joined: Fri Jan 04, 2019 4:17 pm
First Name: Mark
Last Name: Strange
* REQUIRED* Type and Year of Model Ts owned: 1924 Cut Off Touring (now a pickup)
Location: Hillsboro, MO
MTFCA Number: 30944
MTFCI Number: 23667
Board Member Since: 2013

Re: Need some help

Post by CudaMan » Fri Jun 18, 2021 10:53 am

Same here, broken axle shaft. Started off from a stop and heard a pop! The engine ran, but the car wouldn't move in any gear. I called a flatbed and got a tow home. Gave me a good excuse to install the Ruckstell rear axle that I had built. :)
Attachments
IMG_4174.JPG
IMG_4175.JPG
IMG_4176.JPG
Mark Strange
Hillsboro, MO
1924 Cut-off Touring (now a pickup)

User avatar

kelly mt
Posts: 249
Joined: Sun Jan 06, 2019 2:55 pm
First Name: Pat
Last Name: Kelly
* REQUIRED* Type and Year of Model Ts owned: 23 Speedster, 25 TT, 26 Roadster, 27 Tudor
Location: Noxon MT

Re: Need some help

Post by kelly mt » Fri Jun 18, 2021 11:11 am

This had the same symptom, broken pinion gear.
20210325_175926.jpg


speedytinc
Posts: 3840
Joined: Fri Feb 12, 2021 12:24 pm
First Name: john
Last Name: karvaly
* REQUIRED* Type and Year of Model Ts owned: 14/15 wide track roadster. 23 touring, 27 roadster pickup, 20ish rajo touring
Location: orange, ca
MTFCA Number: 14383
Board Member Since: 2020

Re: Need some help

Post by speedytinc » Fri Jun 18, 2021 11:14 am

Put the rear end up on jack stands. Diagnostics. Both sides, pull wheels outward. If they dont come out, rotate. Opposite wheel should rotate backwards. If so, axles/ diff are ok. Could be sheared ring gear bolts or the more common pinion gear key sheared. You can look in the diff. fill hole with it running in gear for ring gear movement or not. If you have gotten this far. Now its the pinion gear or drive shaft.


NorthSouth
Posts: 512
Joined: Tue Apr 16, 2019 9:18 pm
First Name: Steve
Last Name: California
* REQUIRED* Type and Year of Model Ts owned: 1911 Touring, 1912 Warren Speedster
Location: West Coast
MTFCA Number: 50392

Re: Need some help

Post by NorthSouth » Fri Jun 18, 2021 11:27 am

-
John,

Here is a heads up. That wonderful Norm Kling in Alpine, CA helped me replace my rear axels and, among many other lessons that weekend, I learned something the hard way.

Here it is; When breaking down a Model T rear end the first thing you might want to do, after removing the rear end from the car, is go around the housing and torque all 6 of those bolts/ studs. I recommend this because you don't want to find out that one of those is stripped "after" you have reassembled your fresh rear end. Typically, you would have to take it completely apart again to correct this problem. So, a minute spent checking can potentially save you a day's work.
-


speedytinc
Posts: 3840
Joined: Fri Feb 12, 2021 12:24 pm
First Name: john
Last Name: karvaly
* REQUIRED* Type and Year of Model Ts owned: 14/15 wide track roadster. 23 touring, 27 roadster pickup, 20ish rajo touring
Location: orange, ca
MTFCA Number: 14383
Board Member Since: 2020

Re: Need some help

Post by speedytinc » Fri Jun 18, 2021 11:53 am

NorthSouth wrote:
Fri Jun 18, 2021 11:27 am
-
John,

Here is a heads up. That wonderful Norm Kling in Alpine, CA helped me replace my rear axels and, among many other lessons that weekend, I learned something the hard way.

Here it is; When breaking down a Model T rear end the first thing you might want to do, after removing the rear end from the car, is go around the housing and torque all 6 of those bolts/ studs. I recommend this because you don't want to find out that one of those is stripped "after" you have reassembled your fresh rear end. Typically, you would have to take it completely apart again to correct this problem. So, a minute spent checking can potentially save you a day's work.
-
Are you talking about the 6 DRIVE SHAFT bolts/studs?
During a proper rebuild those 6 holes should be inspected & threads chased. Along with removing/cleaning the old grease & dirt. Maybe you find that housing crack. As in a motor overhaul, address all threads

User avatar

Steve Jelf
Posts: 6463
Joined: Fri Jan 04, 2019 9:37 pm
First Name: Steve
Last Name: Jelf
* REQUIRED* Type and Year of Model Ts owned: 1923 touring and a few projects
Location: Parkerfield, Kansas
MTFCA Number: 16175
MTFCI Number: 14758
Board Member Since: 2007
Contact:

Re: Need some help

Post by Steve Jelf » Fri Jun 18, 2021 12:07 pm

Sudden free wheeling and a suddenly locked up rear wheel can both be symptoms of the same malady.

http://dauntlessgeezer.com/DG79.html
The inevitable often happens.
1915 Runabout
1923 Touring


speedytinc
Posts: 3840
Joined: Fri Feb 12, 2021 12:24 pm
First Name: john
Last Name: karvaly
* REQUIRED* Type and Year of Model Ts owned: 14/15 wide track roadster. 23 touring, 27 roadster pickup, 20ish rajo touring
Location: orange, ca
MTFCA Number: 14383
Board Member Since: 2020

Re: Need some help

Post by speedytinc » Fri Jun 18, 2021 12:53 pm

Steve Jelf wrote:
Fri Jun 18, 2021 12:07 pm
Sudden free wheeling and a suddenly locked up rear wheel can both be symptoms of the same malady.

http://dauntlessgeezer.com/DG79.html
If you are saying, a lost thrust washer can create a "freewheeling" NOT POSSIBLE. The thrust washer is .187-.200" thick. The diff assembly does not have that much side to side room. Even if it did, the ring/pinion gear mesh is deeper than .200". The D/S bearing/sleeve would also have to be gone & there would be a continuous nasty noise from the gear mesh overrunning.

Best "guess" is sheared axle or pinion issue. A little testing will narrow it down.

User avatar

Steve Jelf
Posts: 6463
Joined: Fri Jan 04, 2019 9:37 pm
First Name: Steve
Last Name: Jelf
* REQUIRED* Type and Year of Model Ts owned: 1923 touring and a few projects
Location: Parkerfield, Kansas
MTFCA Number: 16175
MTFCI Number: 14758
Board Member Since: 2007
Contact:

Re: Need some help

Post by Steve Jelf » Fri Jun 18, 2021 3:25 pm

I sit corrected. That's good to know.
The inevitable often happens.
1915 Runabout
1923 Touring


Norman Kling
Posts: 4071
Joined: Tue Jan 08, 2019 1:39 pm
First Name: Norman
Last Name: Kling
Location: Alpine California

Re: Need some help

Post by Norman Kling » Fri Jun 18, 2021 4:11 pm

could be anything from the transmission output shaft to the rear wheels. Most often would be the driveshaft, or the rear axle. Next would be the gears in rear axle. Easiest to find would be a broken axle. Unless you have safety hubs, a broken axle would pull right out if you jack up the car.
Norm

User avatar

Mark Gregush
Posts: 4956
Joined: Sat Jan 05, 2019 1:57 pm
First Name: Mark
Last Name: Gregush
* REQUIRED* Type and Year of Model Ts owned: 1925 cutdown PU, 1920 Dodge touring, 1948 F2 Ford flat head 6 pickup 3 speed
Location: Portland Or
MTFCA Number: 52564
Board Member Since: 1999

Re: Need some help

Post by Mark Gregush » Fri Jun 18, 2021 4:42 pm

DO NOT CHASE THOSE BOLTS UNLESS YOU HAVE THE CORRECT TAP
-
[/quote]
Are you talking about the 6 DRIVE SHAFT bolts/studs?
During a proper rebuild those 6 holes should be inspected & threads chased. Along with removing/cleaning the old grease & dirt. Maybe you find that housing crack. As in a motor overhaul, address all threads
[/quote]
I know the voices aren't real but damn they have some good ideas! :shock:

1925 Cut down pickup
1920 Dodge touring
1948 Ford F2 pickup


speedytinc
Posts: 3840
Joined: Fri Feb 12, 2021 12:24 pm
First Name: john
Last Name: karvaly
* REQUIRED* Type and Year of Model Ts owned: 14/15 wide track roadster. 23 touring, 27 roadster pickup, 20ish rajo touring
Location: orange, ca
MTFCA Number: 14383
Board Member Since: 2020

Re: Need some help

Post by speedytinc » Fri Jun 18, 2021 4:56 pm

Norman Kling wrote:
Fri Jun 18, 2021 4:11 pm
could be anything from the transmission output shaft to the rear wheels. Most often would be the driveshaft, or the rear axle. Next would be the gears in rear axle. Easiest to find would be a broken axle. Unless you have safety hubs, a broken axle would pull right out if you jack up the car.
Norm
If the axle broke beyond the outer machined race area, it probably would not pull completely out untill the bearing is removed.
The axle would still pull out far enough to confirm a break or departure from the drive gear.


BobShirleyAtlantaTx
Posts: 361
Joined: Mon Jan 07, 2019 12:44 am
First Name: Bob
Last Name: Shirley
Location: Atlanta Tx
MTFCA Number: 29135

Re: Need some help

Post by BobShirleyAtlantaTx » Fri Jun 18, 2021 6:34 pm

Mark is dead-on, the studs are 7/16 X 16 not a common tap or die. .4375 X 14 threads per inch is standard.
1DDC1E6E-39A4-4248-9B5A-A3648E96FFC6.jpeg
EB743EAE-2816-4AC4-9698-05982F3F05D4.jpeg


speedytinc
Posts: 3840
Joined: Fri Feb 12, 2021 12:24 pm
First Name: john
Last Name: karvaly
* REQUIRED* Type and Year of Model Ts owned: 14/15 wide track roadster. 23 touring, 27 roadster pickup, 20ish rajo touring
Location: orange, ca
MTFCA Number: 14383
Board Member Since: 2020

Re: Need some help

Post by speedytinc » Fri Jun 18, 2021 6:42 pm

That is not correct. Measure them again. The correct thread is 13/32-16 .406 dia.


Scott_Conger
Posts: 6431
Joined: Sun Jan 06, 2019 11:18 am
First Name: Scott
Last Name: Conger
* REQUIRED* Type and Year of Model Ts owned: '13, '15, '19, '23
Location: Clark, WY
Board Member Since: 2005

Re: Need some help

Post by Scott_Conger » Fri Jun 18, 2021 6:47 pm

none of the above

13/32" x 16 thread is what was done at the factory.

Anything else is a bastardization of the correct diameter and pitch

And there is now proof that John K types faster than I.
Scott Conger

Tyranny under the guise of law is still Tyranny

NH Full Flow Float Valves
Obsolete carburetor parts manufactured


BobShirleyAtlantaTx
Posts: 361
Joined: Mon Jan 07, 2019 12:44 am
First Name: Bob
Last Name: Shirley
Location: Atlanta Tx
MTFCA Number: 29135

Re: Need some help

Post by BobShirleyAtlantaTx » Fri Jun 18, 2021 7:02 pm

I stand corrected.

User avatar

TonyB
Posts: 663
Joined: Fri Jan 04, 2019 11:15 am
First Name: Tony
Last Name: Bowker
* REQUIRED* Type and Year of Model Ts owned: 1914 touring
Location: La Mesa, CA
MTFCA Number: 32
MTFCA Life Member: YES
Board Member Since: 2005

Re: Need some help

Post by TonyB » Fri Jun 18, 2021 11:05 pm

I had a similar situation, pulled into the driveway. Opened the garage door and no drive……
I jacked up the rear end and I could turn both wheels and the other would rotate in the opposite direction. I looked inside the transmission and the clutch plate was turning with the crank. So I deduced it was either the UJ or broken pinion gear.
Out came the axle but everything was lust fine.
How could that be possible?????
I poking around I removed the fourth main bearing and the shaft from the clutch was loose??
I pulled the motor and found the problem.
The rivets holding the drive shaft from the clutch plate to the UJ had all pulled out
In my simple mind it’s a real defect with the design in that the rivets are not formed on the clutch side, they are just pressed in and sure enough mine just pulled out. I fixed it by countersinking the front of the clutch plate and spread the rivets while nice and hot.
I know Ford built at least 15,007,033 transmissions but mine failed due to a what I consider a design defect.
I really not sure how to diagnose this failure without pulling it all apart.
Tony Bowker
La Mesa, California
1914 Touring, 1915 Speedster, 1924 Coupe.

Post Reply Previous topicNext topic