Greasing shackles and spindles -vs- oiling

Discuss all things Model T related.
Forum rules
If you need help logging in, or have question about how something works, use the Support forum located here Support Forum
Complete set of Forum Rules Forum Rules

Topic author
bdtutton
Posts: 180
Joined: Thu Feb 18, 2021 10:19 pm
First Name: Bryan
Last Name: Tutton
* REQUIRED* Type and Year of Model Ts owned: 1914 Model T
Location: Southwest, MI

Greasing shackles and spindles -vs- oiling

Post by bdtutton » Wed Jul 07, 2021 2:53 pm

Hello,
I have been looking at a lot of pictures of brass Model T's and have noticed several of them have replaced their brass oilers with grease cups/fittings for shackles and spindles. At first I thought this was a terrible idea, but I use grease to lubricate my 1930 Model A. Maybe it would be a good idea to replace the oilers with grease cups/fittings.

What do you think?
Thanks....Bryan


Scott_Conger
Posts: 6431
Joined: Sun Jan 06, 2019 11:18 am
First Name: Scott
Last Name: Conger
* REQUIRED* Type and Year of Model Ts owned: '13, '15, '19, '23
Location: Clark, WY
Board Member Since: 2005

Re: Greasing shackles and spindles -vs- oiling

Post by Scott_Conger » Wed Jul 07, 2021 3:17 pm

If grease can get to where it is supposed to be, then the spindle or shackle bushings are shot
Scott Conger

Tyranny under the guise of law is still Tyranny

NH Full Flow Float Valves
Obsolete carburetor parts manufactured

User avatar

DanTreace
Posts: 3299
Joined: Sun Jan 06, 2019 10:56 am
First Name: Dan
Last Name: Treace
* REQUIRED* Type and Year of Model Ts owned: '23 cutoff, '25 touring, '27 touring
Location: North Central FL
MTFCA Number: 4838
MTFCI Number: 115
Board Member Since: 2000
Contact:

Re: Greasing shackles and spindles -vs- oiling

Post by DanTreace » Wed Jul 07, 2021 3:20 pm

IMO, stay with oil. The king pin design is for an oil groove to drip oil to the upper and down to the lower bushing. Grease will harden and pack the oil hole.

And the repro modern king pins have little groove around the circumference, unlike the Ford vertical groove that really seeps oil down the shaft.
Grease won't do the job. Some get around that by drilling and adding a grease zerk fitting to the spindle body, that may help, but oil is still best.


IMG_5019 (700x690) (680x670).jpg
IMO, chain saw bar oil is good to use, clings and drips ok, with less running than typical engine oil in the oil can.[/b]
The best way is always the simplest. The attics of the world are cluttered up with complicated failures. Henry Ford
Don’t find fault, find a remedy; anybody can complain. Henry Ford


Virtus
Posts: 70
Joined: Thu Jan 30, 2020 4:37 pm
First Name: Paul
Last Name: Robertson
* REQUIRED* Type and Year of Model Ts owned: Ford model tt 1921 right hand drive
Location: Heathfield, east sussex, uk

Re: Greasing shackles and spindles -vs- oiling

Post by Virtus » Wed Jul 07, 2021 3:27 pm

To use grease the bushes must have grooves or channels on both surfaces to encourage the spread of lubricant to all surfaces. Oil, on the other hand, will form a film on pins and bushes with a smooth surface. I think many nipples are used with a heavier or stickier oil rather than grease.


TXGOAT2
Posts: 6411
Joined: Sun Feb 14, 2021 10:08 pm
First Name: Pat
Last Name: McNallen
* REQUIRED* Type and Year of Model Ts owned: 1926-7 roadster
Location: Graham, Texas
MTFCA Number: 51486
Board Member Since: 2021

Re: Greasing shackles and spindles -vs- oiling

Post by TXGOAT2 » Wed Jul 07, 2021 4:40 pm

I've seen old equipment with lubrication instructions referring to "hard oil". I'm guessing that refers to something like 90W or 140 W. Whatever you put on your Model T steering linkage will wind up, more or less, on your front rims and tires. For ease of cleaning, something like a 40W detergent motor oil might be best. In the Model T era, most all machinery lubrication was designed on the total loss plan, and it required very frequent oiling and wiping. Seals, if any, were rudimentary at best. Where grease was specified, the grease typically served as a lubricant, flushing agent, and to a degree, as a seal to prevent dirt and water entering the bearing. Where the small oil cups were used, such as on Model T steering, it was argued that frequent re-oiling would serve to flush dirt out of the assembly while assuring a supply of clean oil. Around rail yards, factories, and stationary power plants, men were employed as "oilers" and "wipers", aka, "grease monkeys".

User avatar

TRDxB2
Posts: 5412
Joined: Tue Jan 08, 2019 4:56 pm
First Name: Frank
Last Name: Brandi
* REQUIRED* Type and Year of Model Ts owned: Speedster (1919 w 1926)
Location: Moline IL
Board Member Since: 2018

Re: Greasing shackles and spindles -vs- oiling

Post by TRDxB2 » Wed Jul 07, 2021 5:22 pm

After reading several old discussion the issue with oil is that it will flow out of whatever. So some suggest a "heavy sticky oil" like chain saw bar oil. As stated above what you use needs to flow in between the parts it is intended to lubricate. Perhaps the answer is a light weight grease or heavy weight oil :? http://www.mtfca.com/discus/messages/41 ... 1401462623
RED-GREASE?
Vertical parts (tie rod and spindle bolts) may favor heavy oil while horizontal parts (shackles) make work better with grease
https://mtfca.com/phpBB3/viewtopic.php?t=3171
The past is a great place and I don't want to erase it or to regret it, but I don't want to be its prisoner either.
Mick Jagger


Scott_Conger
Posts: 6431
Joined: Sun Jan 06, 2019 11:18 am
First Name: Scott
Last Name: Conger
* REQUIRED* Type and Year of Model Ts owned: '13, '15, '19, '23
Location: Clark, WY
Board Member Since: 2005

Re: Greasing shackles and spindles -vs- oiling

Post by Scott_Conger » Wed Jul 07, 2021 7:59 pm

FWIW, bar oil or way oil is perhaps heavier than automotive motor oil, but is not heavy per-se. It is tacky due to modifiers which are intended to keep it from running out of or off of whatever it's put on. I believe that it is ideal for this use on a Model T in this manner and is my lube of choice.
Scott Conger

Tyranny under the guise of law is still Tyranny

NH Full Flow Float Valves
Obsolete carburetor parts manufactured


Dan Hatch
Posts: 4111
Joined: Tue Jan 08, 2019 7:31 pm
First Name: Dan
Last Name: Hatch
Location: Alabama
MTFCA Number: 49974

Re: Greasing shackles and spindles -vs- oiling

Post by Dan Hatch » Thu Jul 08, 2021 11:01 am

Years ago STP was the go to for this.
But somewhere I read that MBRT used by all the old timers. 😀


Scott_Conger
Posts: 6431
Joined: Sun Jan 06, 2019 11:18 am
First Name: Scott
Last Name: Conger
* REQUIRED* Type and Year of Model Ts owned: '13, '15, '19, '23
Location: Clark, WY
Board Member Since: 2005

Re: Greasing shackles and spindles -vs- oiling

Post by Scott_Conger » Thu Jul 08, 2021 3:46 pm

Dan

you're showing your age

I'll bet you even know who Andy Granatelli was, too

:lol:
Scott Conger

Tyranny under the guise of law is still Tyranny

NH Full Flow Float Valves
Obsolete carburetor parts manufactured


Dan Hatch
Posts: 4111
Joined: Tue Jan 08, 2019 7:31 pm
First Name: Dan
Last Name: Hatch
Location: Alabama
MTFCA Number: 49974

Re: Greasing shackles and spindles -vs- oiling

Post by Dan Hatch » Thu Jul 08, 2021 3:50 pm

Does not everyone????
The real question is who was it that always talked about the MBRT? That will really tell how long someone has been on this forum. Dan :roll:


Scott_Conger
Posts: 6431
Joined: Sun Jan 06, 2019 11:18 am
First Name: Scott
Last Name: Conger
* REQUIRED* Type and Year of Model Ts owned: '13, '15, '19, '23
Location: Clark, WY
Board Member Since: 2005

Re: Greasing shackles and spindles -vs- oiling

Post by Scott_Conger » Thu Jul 08, 2021 3:59 pm

Hugh aren't going to tell, are you?

I won't.
Scott Conger

Tyranny under the guise of law is still Tyranny

NH Full Flow Float Valves
Obsolete carburetor parts manufactured


TXGOAT2
Posts: 6411
Joined: Sun Feb 14, 2021 10:08 pm
First Name: Pat
Last Name: McNallen
* REQUIRED* Type and Year of Model Ts owned: 1926-7 roadster
Location: Graham, Texas
MTFCA Number: 51486
Board Member Since: 2021

Re: Greasing shackles and spindles -vs- oiling

Post by TXGOAT2 » Thu Jul 08, 2021 4:34 pm

....... GRANCOR..........


Dan Hatch
Posts: 4111
Joined: Tue Jan 08, 2019 7:31 pm
First Name: Dan
Last Name: Hatch
Location: Alabama
MTFCA Number: 49974

Re: Greasing shackles and spindles -vs- oiling

Post by Dan Hatch » Thu Jul 08, 2021 4:48 pm

Scott you are showing your forum age now.

I miss his post. Added a lot to the forum. Dan

User avatar

TRDxB2
Posts: 5412
Joined: Tue Jan 08, 2019 4:56 pm
First Name: Frank
Last Name: Brandi
* REQUIRED* Type and Year of Model Ts owned: Speedster (1919 w 1926)
Location: Moline IL
Board Member Since: 2018

Re: Greasing shackles and spindles -vs- oiling

Post by TRDxB2 » Thu Jul 08, 2021 5:41 pm

FORUM Dictionary
>MBRT - modified bitumen roofing tar
>GRANCOR - GRANatelli CORporation
>STP - Scientifically Treated Petroleum
WITH STOP LEAK ! Gotta check it out
Attachments
STP.png
The past is a great place and I don't want to erase it or to regret it, but I don't want to be its prisoner either.
Mick Jagger

User avatar

CudaMan
Posts: 2385
Joined: Fri Jan 04, 2019 4:17 pm
First Name: Mark
Last Name: Strange
* REQUIRED* Type and Year of Model Ts owned: 1924 Cut Off Touring (now a pickup)
Location: Hillsboro, MO
MTFCA Number: 30944
MTFCI Number: 23667
Board Member Since: 2013

Re: Greasing shackles and spindles -vs- oiling

Post by CudaMan » Thu Jul 08, 2021 6:36 pm

I use chain saw bar oil in the oilers for my spindles, but I pump grease into the oilers for the shackles until I see grease squeezing out both ends. I use a large grease needle with a rubber tip that seals against the opening of the oiler. I use the factory jack to raise each shackle enough for the grease needle to reach both oilers. :)
Attachments
IMG_5699.JPG
Mark Strange
Hillsboro, MO
1924 Cut-off Touring (now a pickup)

User avatar

John iaccino
Posts: 746
Joined: Mon Jan 07, 2019 5:25 am
First Name: John
Last Name: Iaccino
* REQUIRED* Type and Year of Model Ts owned: 1911 Roadster, Open Runnabout
Location: Rhinebeck, NY
MTFCA Number: 17802

Re: Greasing shackles and spindles -vs- oiling

Post by John iaccino » Thu Jul 08, 2021 6:44 pm

The clearances for the spindles do not lend themselves to grease. Oil is the best thing to use for spindles. A few drops every time you drive is what is needed.

User avatar

paddy1998
Posts: 190
Joined: Tue Feb 05, 2019 4:28 pm
First Name: Scott
Last Name: Delaney
* REQUIRED* Type and Year of Model Ts owned: 1922/23 Touring
Location: Joliet, Illinois
MTFCA Number: 50356

Re: Greasing shackles and spindles -vs- oiling

Post by paddy1998 » Thu Jul 08, 2021 6:59 pm

Since we're sharing, this spring when I rolled it out for the season I had some leftover 50/50 mix of 85w-140 and Lucas Oil Stabilizer that I used in my other diffs, so I tried that out in the oil cups.

Seems to be working. Probably want something a little thinner in the fall.


Kerry
Posts: 1297
Joined: Mon Jan 07, 2019 2:42 pm
First Name: Frank
Last Name: van Ekeren
* REQUIRED* Type and Year of Model Ts owned: 1916 touring, 1916 pick-up, 1924 coupe, 1926 touring, 1927 touring
Location: Rosedale Vic Australia

Re: Greasing shackles and spindles -vs- oiling

Post by Kerry » Thu Jul 08, 2021 7:01 pm

One of my T's was converted to grease all round more than 25 years ago that I know of, a very high mileage out back trips and tours. Can't fault any spindle or shackle as yet :D
If I can't be stuffed to run around with an oil can first thing on any of the others, it's the T I jump in and go.

User avatar

KWTownsend
Posts: 1122
Joined: Mon Jan 07, 2019 6:51 pm
First Name: Keith
Last Name: Townsend
* REQUIRED* Type and Year of Model Ts owned: late 1911 touring, 1915 runabout, 1919 touring, brass speedster
Location: Gresham, Orygun
MTFCA Number: 14778
MTFCA Life Member: YES
MTFCI Number: 16305
Board Member Since: 1999

Re: Greasing shackles and spindles -vs- oiling

Post by KWTownsend » Fri Jul 09, 2021 12:54 am

I've used bar oil for the past 40 years. It is my chassis lube of choice.

Keith


Been Here Before
Posts: 625
Joined: Mon Oct 07, 2019 2:00 pm
First Name: George John
Last Name: Drobnock
* REQUIRED* Type and Year of Model Ts owned: 1922 Coupe
Location: Central Pennsylvania

Re: Greasing shackles and spindles -vs- oiling

Post by Been Here Before » Fri Jul 09, 2021 10:38 am

Yes bar oil is the best. I just replaced all my chassis oilers. Had some help.
DSC_0075.JPG


D Stroud
Posts: 1015
Joined: Sun Jan 06, 2019 10:45 am
First Name: David
Last Name: Stroud
* REQUIRED* Type and Year of Model Ts owned: 1925 Coupe
Location: Mound City, MO 64470
Board Member Since: 2011

Re: Greasing shackles and spindles -vs- oiling

Post by D Stroud » Sun Jul 18, 2021 4:13 am

At one time, I thought grease would be better than oil in the spindles. Then, I remembered how grease will always take the path of least resistance. I learned that 50 years ago greasing the U Joints on my old '65 Chevy 3/4 ton 4 wheel drive pickup. There was always one side of the cross that wouldn't take grease. I would have to take a small jack and put pressure on the opposite trunion so grease would go to where it was needed. Had to do that pretty much everytime. On the T, I found that heavy oil works pretty good, gets kind of messy, but that's better than running dry. JMHO Dave

PS Mark Strange, where did you find oilers for the front spring that will clear the shackles?
1925 mostly original coupe.


Nv Bob
Posts: 777
Joined: Mon Jan 07, 2019 11:04 pm
First Name: Bob
Last Name: Middleton
* REQUIRED* Type and Year of Model Ts owned: 18 roadster 1810 brand X
Location: Western nv

Re: Greasing shackles and spindles -vs- oiling

Post by Nv Bob » Mon Jul 19, 2021 12:33 am

Agree if grease get where needed your close to replacement
I use chain saw oil


Model T Ron
Posts: 322
Joined: Tue Jun 08, 2021 12:31 am
First Name: Ronald
Last Name: Bakow
* REQUIRED* Type and Year of Model Ts owned: 1915 Model T Touring
Location: Troutman, NC
MTFCI Number: 25350

Re: Greasing shackles and spindles -vs- oiling

Post by Model T Ron » Mon Jul 19, 2021 1:18 am

My new to me 1915 touring has grease fittings and I have a feeling they have been on for some time. The car is in very good shape and it was driven. My first reaction was this may have not been a good idea but after taking some time to assess the condition of the car I would have to say grease fittings if properly installed are a good thing.


Kerry
Posts: 1297
Joined: Mon Jan 07, 2019 2:42 pm
First Name: Frank
Last Name: van Ekeren
* REQUIRED* Type and Year of Model Ts owned: 1916 touring, 1916 pick-up, 1924 coupe, 1926 touring, 1927 touring
Location: Rosedale Vic Australia

Re: Greasing shackles and spindles -vs- oiling

Post by Kerry » Mon Jul 19, 2021 1:40 am

I think the question would be, how many cars, truck etc used grease or oilers at that time and what was fazed out to have a preferred lube. I've been twisting spanners for well over 50 years and when it came to servicing, it wasn't with an oil can other than the T's. We all know how tight Henry was and any cost saving was always implemented, tin insert or grease nipple, mmm, what would the choice be?


TXGOAT2
Posts: 6411
Joined: Sun Feb 14, 2021 10:08 pm
First Name: Pat
Last Name: McNallen
* REQUIRED* Type and Year of Model Ts owned: 1926-7 roadster
Location: Graham, Texas
MTFCA Number: 51486
Board Member Since: 2021

Re: Greasing shackles and spindles -vs- oiling

Post by TXGOAT2 » Mon Jul 19, 2021 9:32 am

Something to consider: In 1907, when the Model T was designed, what was commonly available in the way of commercially prepared automobile chassis grease? What was available in the way of tools and fittings for applying such grease to chassis parts? "Dope cups" were not suitable for most chassis lube points. Most farmers in 1907 had an oil can of some sort, and If they had a Model T, they had motor oil. For a great many early Model T owners, the car was the only power driven machine they owned.

User avatar

Will_Vanderburg
Posts: 811
Joined: Sun Jan 06, 2019 3:59 pm
First Name: William
Last Name: Vanderburg
* REQUIRED* Type and Year of Model Ts owned: 2
Location: Jackson, NJ
MTFCA Number: 28382

Re: Greasing shackles and spindles -vs- oiling

Post by Will_Vanderburg » Mon Jul 19, 2021 11:19 am

The only place on my car that I’ve retrofitted grease fittings is inside the dope cups
William L Vanderburg

1925 Touring
1922 Center Door Sedan

User avatar

Quickm007
Posts: 1198
Joined: Mon Jan 07, 2019 10:58 am
First Name: Mario
Last Name: Brossard
* REQUIRED* Type and Year of Model Ts owned: 1911 Touring and 1914 speedster
Location: Quebec City Canada
MTFCA Number: 30981
MTFCI Number: 30981
Board Member Since: 1999

Re: Greasing shackles and spindles -vs- oiling

Post by Quickm007 » Mon Jul 19, 2021 11:29 am

CudaMan wrote:
Thu Jul 08, 2021 6:36 pm
I use chain saw bar oil in the oilers for my spindles, but I pump grease into the oilers for the shackles until I see grease squeezing out both ends. I use a large grease needle with a rubber tip that seals against the opening of the oiler. I use the factory jack to raise each shackle enough for the grease needle to reach both oilers. :)
I like that. I will try it with my 1914 speedster as well
Super Mario Bross ;)

1911 Touring
1914 Speedster

User avatar

RustyFords
Posts: 1554
Joined: Sun Jan 06, 2019 11:16 am
First Name: Don
Last Name: Allen
* REQUIRED* Type and Year of Model Ts owned: 1924 Touring
Location: Houston, TX
MTFCA Number: 50001

Re: Greasing shackles and spindles -vs- oiling

Post by RustyFords » Mon Jul 19, 2021 1:06 pm

I'm using a high quality chainsaw bar oil.

I guess time will tell if it's done the job.
1924 Touring


TXGOAT2
Posts: 6411
Joined: Sun Feb 14, 2021 10:08 pm
First Name: Pat
Last Name: McNallen
* REQUIRED* Type and Year of Model Ts owned: 1926-7 roadster
Location: Graham, Texas
MTFCA Number: 51486
Board Member Since: 2021

Re: Greasing shackles and spindles -vs- oiling

Post by TXGOAT2 » Mon Jul 19, 2021 2:52 pm

Bar oil with some powdered graphite intended for locks would probably do a good job.

User avatar

dykker5502
Posts: 410
Joined: Mon Jan 07, 2019 7:01 pm
First Name: Michael
Last Name: Deichmann
* REQUIRED* Type and Year of Model Ts owned: 1914 Touring, 1921 Roadster P/U, 1922 Fordor (danish custom body)
Location: Rågeleje, Denmark
MTFCA Number: 29116
Board Member Since: 2007

Re: Greasing shackles and spindles -vs- oiling

Post by dykker5502 » Tue Jul 20, 2021 6:41 am

10+ years ago, when i got my first T (the Fordor) I replaced the spindles and considered to change the oilers to grease niples, but kept the oilers. The next 8 years I oiled the whole chassis at some regular times - mostly before longer rides (NOT before every ride). Then it was time for the next inspection (MOT) and I could just see that there was a little slop, so I decided to replace, but I was pretty amazed that the oiul had done it so well. I use the W600/SAE 250 rearend oil.
I have actually also considered chainsaw oil siunce it have this feature of being sticky (so it stays as long as possible on the chain) and maybe I'll switch to that when my SAE250 bottle is empty.
Ford Model T 1914 Touring
Ford Model T 1921 Roadster Pick-up
Ford Model T 1922 Fordor (danish build body)
ECCT, Strobospark, HCCT(Sold), Rebuilding coils


Original Smith
Posts: 3284
Joined: Tue Jan 08, 2019 10:43 am
First Name: Larry
Last Name: Smith
* REQUIRED* Type and Year of Model Ts owned: 13 Touring, 13 Roadster, 17 Coupelet, 25 Roadster P/U
Location: Lomita, California
MTFCA Number: 121
MTFCA Life Member: YES
MTFCI Number: 16310

Re: Greasing shackles and spindles -vs- oiling

Post by Original Smith » Wed Jul 21, 2021 12:50 am

I've never not done what the Ford Service Book says. I've never had a problem ever! I don't know why restorers almost always have to change what Ford recommended. All I've done is to use brass bushings like the early cars, so as not to wear the perfect shackles and king pins in my cars. I have a T that I've owned for over 60 years, and have never used anything but engine oil in the bushings. The car now has over 55,000 miles with no wear in any of those places.

Post Reply Previous topicNext topic