Front License Bracket - Polished Brass - Problem
Forum rules
If you need help logging in, or have question about how something works, use the Support forum located here Support Forum
Complete set of Forum Rules Forum Rules
If you need help logging in, or have question about how something works, use the Support forum located here Support Forum
Complete set of Forum Rules Forum Rules
-
Topic author - Posts: 180
- Joined: Thu Feb 18, 2021 10:19 pm
- First Name: Bryan
- Last Name: Tutton
- * REQUIRED* Type and Year of Model Ts owned: 1914 Model T
- Location: Southwest, MI
Front License Bracket - Polished Brass - Problem
I recently purchased a Polished Brass Front License Bracket (T-3664-CHPO) from Snyders and I am having a little problem. The bracket has a nice feature that allows you to lock your crank in place so people do not fool around with your car. The problem I have is that I can not start my car even when the anti-theft feature is flipped up and away because the crank hits the bracket. I called Snyders and they said they sell a bunch of these and have not heard of any problems.
https://snydersantiqueauto.com/ProductD ... CKET-PLAIN
I am thinking that my crank handle may be too short and that is why it hits the bracket.
Has anyone else had an issue with this bracket?
https://snydersantiqueauto.com/ProductD ... CKET-PLAIN
I am thinking that my crank handle may be too short and that is why it hits the bracket.
Has anyone else had an issue with this bracket?
-
- Posts: 3923
- Joined: Sun Jan 06, 2019 8:00 pm
- First Name: John
- Last Name: Kuehn
- * REQUIRED* Type and Year of Model Ts owned: 19 Roadster, 21 Touring, 24 Coupe
- Location: Texas
- MTFCA Number: 28924
Re: Front License Bracket - Polished Brass - Problem
Does you crank hang down just a bit when it’s pulled out as far as it will go? If it does the crank bushing in the pan may be worn. It doesn’t take much wear for it to droop.
-
- Posts: 535
- Joined: Sun Jan 06, 2019 2:51 pm
- First Name: Terry & Sharon
- Last Name: Miller
- * REQUIRED* Type and Year of Model Ts owned: 1920 Center Door, 1920 TTWood cab Farm Truck with cable dump grain bed, 1920 TT C-Cab with express bed, 1927 Wood body Dairy Delivery truck
- Location: Westminster, CO
- MTFCA Number: 32583
- Board Member Since: 2017
Re: Front License Bracket - Polished Brass - Problem
Is your crank bent. I have seen some that are. You might try bending the crank out a little to get clearance.
-
Topic author - Posts: 180
- Joined: Thu Feb 18, 2021 10:19 pm
- First Name: Bryan
- Last Name: Tutton
- * REQUIRED* Type and Year of Model Ts owned: 1914 Model T
- Location: Southwest, MI
Re: Front License Bracket - Polished Brass - Problem
The bushing is tight and I don't think my crank is bent....but I can look at it again.
I am just wondering if my crank is shorter than normal. (No jokes here guys)
Does anyone know the specs for a normal 1913-1914 crank?
I am just wondering if my crank is shorter than normal. (No jokes here guys)
Does anyone know the specs for a normal 1913-1914 crank?
-
- Posts: 2293
- Joined: Sun Jan 06, 2019 5:25 pm
- First Name: George
- Last Name: House
- * REQUIRED* Type and Year of Model Ts owned: ‘10 Maxwell AA, ‘11Hupp Model 20, Two 1914 Ford runabouts, 19 centerdoor, 25 C Cab,26 roadster
- Location: Northern Caldwell County TX
- MTFCA Number: 115
- MTFCA Life Member: YES
- Board Member Since: 1999
Re: Front License Bracket - Polished Brass - Problem
I’ve been hearing a bent crank would likely be Peronies Disease and you should see a doctor.
I don’t know why I turned out this way. My parents were decent people.
-
- Posts: 3923
- Joined: Sun Jan 06, 2019 8:00 pm
- First Name: John
- Last Name: Kuehn
- * REQUIRED* Type and Year of Model Ts owned: 19 Roadster, 21 Touring, 24 Coupe
- Location: Texas
- MTFCA Number: 28924
Re: Front License Bracket - Polished Brass - Problem
Maybe you can slot the holes in the plate holder so it will go further back.
-
- Posts: 443
- Joined: Mon Jan 07, 2019 10:37 am
- First Name: Dan
- Last Name: Haynes
- * REQUIRED* Type and Year of Model Ts owned: several
- Location: Lodi, CA
Re: Front License Bracket - Polished Brass - Problem
The riser that holds the forked part that holds the crank can easily be bent forward or back to give the clearance you need.
I had to do a lot of work to mine, the holes on the motor mount bracket were too close together, they were too far back, the riser was bent, the fork was formed wrong (it was ground wrong for the leaf spring).
The part is a cool accessory, but they have troubles with the details.
I had to do a lot of work to mine, the holes on the motor mount bracket were too close together, they were too far back, the riser was bent, the fork was formed wrong (it was ground wrong for the leaf spring).
The part is a cool accessory, but they have troubles with the details.
"The further a society drifts from truth, the more it will hate those who speak it." -George Orwell
-
- Posts: 3298
- Joined: Tue Jan 08, 2019 10:43 am
- First Name: Larry
- Last Name: Smith
- * REQUIRED* Type and Year of Model Ts owned: 13 Touring, 13 Roadster, 17 Coupelet, 25 Roadster P/U
- Location: Lomita, California
- MTFCA Number: 121
- MTFCA Life Member: YES
- MTFCI Number: 16310
Re: Front License Bracket - Polished Brass - Problem
Could it be the part you are speaking of is a reproduction?
-
Topic author - Posts: 180
- Joined: Thu Feb 18, 2021 10:19 pm
- First Name: Bryan
- Last Name: Tutton
- * REQUIRED* Type and Year of Model Ts owned: 1914 Model T
- Location: Southwest, MI
Re: Front License Bracket - Polished Brass - Problem
Dan...do you have any pictures of what it looks like after you worked on it? It would be nice to see your modifications.
.
And yes Larry....this is a reproduction part that does not seem to fit quite right.
.
I tried looking at this from another point of view and realized that if I added some spacers it would raise it up to better align the bracket with the crank hole. There would still be some minor interference, but I would not have to modify the bracket very much to make it work. The only problem I have is the u-bolts are not long enough....I guess I will have to look for longer u-bolts to try my test.
.
And yes Larry....this is a reproduction part that does not seem to fit quite right.
.
I tried looking at this from another point of view and realized that if I added some spacers it would raise it up to better align the bracket with the crank hole. There would still be some minor interference, but I would not have to modify the bracket very much to make it work. The only problem I have is the u-bolts are not long enough....I guess I will have to look for longer u-bolts to try my test.
-
- Posts: 327
- Joined: Fri Jan 04, 2019 10:18 pm
- First Name: Harry
- Last Name: Lillo
- * REQUIRED* Type and Year of Model Ts owned: Speedsters, racers, depot hack, coupe
- Location: Calgary
- MTFCA Number: 13996
Re: Front License Bracket - Polished Brass - Problem
I have one of the reproduction brackets that I have not installed.
I do however have the actual original that was used to create these reproduction pieces.
My cast iron original was loaned to make the brass replica.
Later in the day I will check one against the other to see the differences.
Harry Lillo
I do however have the actual original that was used to create these reproduction pieces.
My cast iron original was loaned to make the brass replica.
Later in the day I will check one against the other to see the differences.
Harry Lillo
-
- Posts: 3873
- Joined: Fri Feb 12, 2021 12:24 pm
- First Name: john
- Last Name: karvaly
- * REQUIRED* Type and Year of Model Ts owned: 14/15 wide track roadster. 23 touring, 27 roadster pickup, 20ish rajo touring
- Location: orange, ca
- MTFCA Number: 14383
- Board Member Since: 2020
Re: Front License Bracket - Polished Brass - Problem
Would a little crank tweaking make it work?bdtutton wrote: ↑Thu Jul 22, 2021 10:54 amDan...do you have any pictures of what it looks like after you worked on it? It would be nice to see your modifications.
.
And yes Larry....this is a reproduction part that does not seem to fit quite right.
.
I tried looking at this from another point of view and realized that if I added some spacers it would raise it up to better align the bracket with the crank hole. There would still be some minor interference, but I would not have to modify the bracket very much to make it work. The only problem I have is the u-bolts are not long enough....I guess I will have to look for longer u-bolts to try my test.
Say going 95 degrees @ the pan & handle.
A friend installed the similar unit W/O the locking fork. No issues.