I have a Paterson speedo drive which has a spiral bronze gear inside the transmission and has a special transmission cover plate. I need a replacement fibre gear that goes on the end of the shaft and is driven by the spiral gear. Does anyone have/know of a source for same?
Allan from down under.
Paterson speedo drive gear.
Forum rules
If you need help logging in, or have question about how something works, use the Support forum located here Support Forum
Complete set of Forum Rules Forum Rules
If you need help logging in, or have question about how something works, use the Support forum located here Support Forum
Complete set of Forum Rules Forum Rules
-
Allan
Topic author - Posts: 6609
- Joined: Sun Jan 06, 2019 7:21 pm
- First Name: Allan
- Last Name: Bennett
- * REQUIRED* Type and Year of Model Ts owned: 1912 van, 1917 shooting brake, 1929 roadster buckboard, 1924 tourer, 1925 barn find buckboard, 1925 D &F wide body roadster, 1927LHD Tudor sedan.
- Location: Gawler, Australia
-
Joe Bell
- Posts: 1174
- Joined: Thu Feb 21, 2019 1:20 pm
- First Name: Joe
- Last Name: Bell
- * REQUIRED* Type and Year of Model Ts owned: 24 Fordor
- Location: Tiffin Ohio
Re: Paterson speedo drive gear.
Tim Morsher had some made a couple years ago, he may still have one??
-
Allan
Topic author - Posts: 6609
- Joined: Sun Jan 06, 2019 7:21 pm
- First Name: Allan
- Last Name: Bennett
- * REQUIRED* Type and Year of Model Ts owned: 1912 van, 1917 shooting brake, 1929 roadster buckboard, 1924 tourer, 1925 barn find buckboard, 1925 D &F wide body roadster, 1927LHD Tudor sedan.
- Location: Gawler, Australia
Re: Paterson speedo drive gear.
Thanks Joe. I have emailed Tim. Does anyone know of an alternative source if Tim has none?
Allan from down under.
Allan from down under.
-
doodlebugt
- Posts: 42
- Joined: Sun Jan 06, 2019 3:46 pm
- First Name: Bruce
- Last Name: Csorba
- * REQUIRED* Type and Year of Model Ts owned: 1915 4 spring Rajo racer, 1917 C-cab van, 1925 Dalgety tourer
- Location: Melbourne, Australia
Re: Paterson speedo drive gear.
What number of teeth do you need? When I used to see NOS gears around, they were for 4:1 diffs or trucks. I don't think I have any drive pieces left, but may still have a brochure with the ratios listed.
Bruce
Bruce
Bruce Csorba
Melbourne, Australia
15 4-spring Rajo racer
17 C-cab van
25 "Dalgety" Tourer
Melbourne, Australia
15 4-spring Rajo racer
17 C-cab van
25 "Dalgety" Tourer
-
Allan
Topic author - Posts: 6609
- Joined: Sun Jan 06, 2019 7:21 pm
- First Name: Allan
- Last Name: Bennett
- * REQUIRED* Type and Year of Model Ts owned: 1912 van, 1917 shooting brake, 1929 roadster buckboard, 1924 tourer, 1925 barn find buckboard, 1925 D &F wide body roadster, 1927LHD Tudor sedan.
- Location: Gawler, Australia
Re: Paterson speedo drive gear.
Thanks Bruce, I will call you. The one on my drive was a 10 tooth gear, but I am not that fussy. any gear will be better than none.
I drew a blank with Tim Morsher as a source. He has sold out. Did anyone out there purchase a couple of his gears, and holds one as a spare?
The top right hand corner screw hole in the cover is the normal round hole. All the others are slotted, suggesting the cover has to be screwed around a bit to get the gear to mesh with the spiral gear on the trans. Does anyone have info/instructions on this?
Allan from down under.
I drew a blank with Tim Morsher as a source. He has sold out. Did anyone out there purchase a couple of his gears, and holds one as a spare?
The top right hand corner screw hole in the cover is the normal round hole. All the others are slotted, suggesting the cover has to be screwed around a bit to get the gear to mesh with the spiral gear on the trans. Does anyone have info/instructions on this?
Allan from down under.