I need help with a Neverout License plate bracket. It appears that it can be mounted either on a spade mount or a round post mount. I don't know if it is an original or a copy but the lettering is sharp and easy to read, When it is mounted, "Neverout" and "Patented" are shown facing to the rear. On the other side, It shows "Rose Mfg. Co. Phila." and the number "701" on the tab at the bottom.
I have seen several posts about Neverout License Plate Brackets but did not find one like this one. Does anyone have a picture to show how the License Plate would be mounted? The portion to the right of the "Neverout" name is 5 1/2" wide with only one bolt hole.
Are the two round holes (on the left in the top picture) for mounting lights? They both have a bolt for tightening around something. Pictures or ads would be helpful.
Thanks for your help.
(How do you rotate pictures?)Neverout License Bracket
Forum rules
If you need help logging in, or have question about how something works, use the Support forum located here Support Forum
Complete set of Forum Rules Forum Rules
If you need help logging in, or have question about how something works, use the Support forum located here Support Forum
Complete set of Forum Rules Forum Rules
-
Topic author - Posts: 205
- Joined: Tue Jan 08, 2019 11:13 am
- First Name: James
- Last Name: Sanford
- * REQUIRED* Type and Year of Model Ts owned: 14 Touring, 26 Roadster, 27 Roadster
- Location: Lucas, TX
-
- Posts: 3284
- Joined: Tue Jan 08, 2019 10:43 am
- First Name: Larry
- Last Name: Smith
- * REQUIRED* Type and Year of Model Ts owned: 13 Touring, 13 Roadster, 17 Coupelet, 25 Roadster P/U
- Location: Lomita, California
- MTFCA Number: 121
- MTFCA Life Member: YES
- MTFCI Number: 16310
Re: Neverout License Bracket
That style is scarce. If it had a blade license lamp mount, I'd like one similar to that for my '13!
-
Topic author - Posts: 205
- Joined: Tue Jan 08, 2019 11:13 am
- First Name: James
- Last Name: Sanford
- * REQUIRED* Type and Year of Model Ts owned: 14 Touring, 26 Roadster, 27 Roadster
- Location: Lucas, TX
Re: Neverout License Bracket
Still looking for information on this license plate bracket.
Thanks
Thanks
-
- Posts: 3299
- Joined: Sun Jan 06, 2019 10:56 am
- First Name: Dan
- Last Name: Treace
- * REQUIRED* Type and Year of Model Ts owned: '23 cutoff, '25 touring, '27 touring
- Location: North Central FL
- MTFCA Number: 4838
- MTFCI Number: 115
- Board Member Since: 2000
- Contact:
Re: Neverout License Bracket
That #701 was rather unusual type from 1916. It held electric lights for tail and white for backup lamp.
Here is adv.:
The line of Rose Mfg. 'Neverout's' for license pads or plates was quite amazing.
Here is adv.:
The line of Rose Mfg. 'Neverout's' for license pads or plates was quite amazing.
The best way is always the simplest. The attics of the world are cluttered up with complicated failures. Henry Ford
Don’t find fault, find a remedy; anybody can complain. Henry Ford
Don’t find fault, find a remedy; anybody can complain. Henry Ford
-
- Posts: 214
- Joined: Sun Jan 06, 2019 12:55 pm
- First Name: Walt
- Last Name: Berdan
- * REQUIRED* Type and Year of Model Ts owned: '18 Speedster had 25 touring and 26 coupe
- Location: Bellevue, WA
- MTFCA Number: 16421
Re: Neverout License Bracket
I have a No621 bracket that came with a bunch of T junk stuff. Is this the type you are looking for Larry?