ILLUSIVE RATTLE CONTINUES

Discuss all things Model T related.
Forum rules
If you need help logging in, or have question about how something works, use the Support forum located here Support Forum
Complete set of Forum Rules Forum Rules

Topic author
John Dow
Posts: 177
Joined: Tue Jan 29, 2019 10:21 am
First Name: John
Last Name: Dow
* REQUIRED* Type and Year of Model Ts owned: 1923 Touring
Location: Leawood, Ks
MTFCA Number: 32344
Board Member Since: 2015

ILLUSIVE RATTLE CONTINUES

Post by John Dow » Thu Aug 22, 2019 12:18 pm

Hello again, This is another try at hoping to get some other ideas of the origin of a %$#@ rattle in my 1923 Touring. The rattle occurs when at idle or coasting. The engine was rebuilt some years ago with aluminum pistons, compression is good. Here is what I've checked: shorting out #3 the rattle stops, babbitt is mint, the rod cap is adjusted to proper clearance (on all 4), the rod cap bolt head(s) is/are not hitting the cam, the center main bearing nor the center cam bearing have any play, the rods do not move side to side in the pistons, the cam has no end play, i have replaced the timing gear as well as the generator gear. I'm truly stumped. Any ideas you folks would have would be greatly appreciated. Thank you.


Les Schubert
Posts: 1311
Joined: Thu Jan 10, 2019 5:47 pm
First Name: Les
Last Name: Schubert
* REQUIRED* Type and Year of Model Ts owned: 27 roadster 13 touring
Location: Calgary

Re: ILLUSIVE RATTLE CONTINUES

Post by Les Schubert » Thu Aug 22, 2019 2:49 pm

Camshaft end play?


Topic author
John Dow
Posts: 177
Joined: Tue Jan 29, 2019 10:21 am
First Name: John
Last Name: Dow
* REQUIRED* Type and Year of Model Ts owned: 1923 Touring
Location: Leawood, Ks
MTFCA Number: 32344
Board Member Since: 2015

Re: ILLUSIVE RATTLE CONTINUES

Post by John Dow » Thu Aug 22, 2019 7:21 pm

Thanks Les. I've checked it and that's not it.


Moxie26
Posts: 1314
Joined: Sun Jan 06, 2019 8:20 pm
First Name: Robert
Last Name: Jablonski
* REQUIRED* Type and Year of Model Ts owned: 1926 Runabout
Location: New Jersey
MTFCA Number: 407
MTFCA Life Member: YES
Board Member Since: 1999

Re: ILLUSIVE RATTLE CONTINUES

Post by Moxie26 » Thu Aug 22, 2019 11:29 pm

Loose fan belt pulley?

User avatar

Jem
Posts: 192
Joined: Sun Jan 06, 2019 5:37 pm
First Name: Jem
Last Name: Bowkett
* REQUIRED* Type and Year of Model Ts owned: 1909 Touring #9267
Location: Spalding United Kingdom
Board Member Since: 1999

Re: ILLUSIVE RATTLE CONTINUES

Post by Jem » Fri Aug 23, 2019 2:22 am

I have had problems on 2 engines with piston pins seizing in alloy pistons after a couple of thousand miles. That causes the piston to cock over and clatter against the bore. Pull #3 and check the piston pin.

I also have a noisy cam gear on 1 engine, even though it's new. It has 7thou backlash, the main bearings have been bored wrongly so the crank is too far away from the cam. I have an oversize cam gear on order.

User avatar

perry kete
Posts: 1563
Joined: Sun Jan 06, 2019 11:46 am
First Name: Dennis
Last Name: Seth
* REQUIRED* Type and Year of Model Ts owned: 1922 Coupe 1927 Touring
Location: Jefferson Ohio

Re: ILLUSIVE RATTLE CONTINUES

Post by perry kete » Fri Aug 23, 2019 7:25 am

Try more polydent....I discovered it was just my loose dentures making the rattling noise! :lol:
1922 Coupe & 1927 Touring


Topic author
John Dow
Posts: 177
Joined: Tue Jan 29, 2019 10:21 am
First Name: John
Last Name: Dow
* REQUIRED* Type and Year of Model Ts owned: 1923 Touring
Location: Leawood, Ks
MTFCA Number: 32344
Board Member Since: 2015

Re: ILLUSIVE RATTLE CONTINUES

Post by John Dow » Fri Aug 23, 2019 7:44 am

Jem- I've about concluded you may have hit upon the cause. Actually, there is nothing left!! So what catastrophic event is looming? In other words, what is the danger in driving it until winter when I can pull the plate and the head? Many thanks for your response.


Topic author
John Dow
Posts: 177
Joined: Tue Jan 29, 2019 10:21 am
First Name: John
Last Name: Dow
* REQUIRED* Type and Year of Model Ts owned: 1923 Touring
Location: Leawood, Ks
MTFCA Number: 32344
Board Member Since: 2015

Re: ILLUSIVE RATTLE CONTINUES

Post by John Dow » Fri Aug 23, 2019 8:47 am

So Jem, what's the remedy??


Scott_Conger
Posts: 6428
Joined: Sun Jan 06, 2019 11:18 am
First Name: Scott
Last Name: Conger
* REQUIRED* Type and Year of Model Ts owned: '13, '15, '19, '23
Location: Clark, WY
Board Member Since: 2005

Re: ILLUSIVE RATTLE CONTINUES

Post by Scott_Conger » Fri Aug 23, 2019 1:55 pm

A tight wrist pin will typically continue to knock even if the plug is shorted out, and most often shows up in relatively little time after a rebuild. It will tend to knock at all speeds and is certainly not most promenent when idling or coasting unless other noises are masking it under other conditions. An engine built "some years ago" would have to have precious few miles on it to now just start knocking due to tight piston. It will typically start as a cold knock and go away when warm and then possibly start to seize and knock all the time. If it is tight, it will become a very bad thing soon enough. I personally don't think that's what it is, but am certainly always able to admit to being wrong, and learning something new.

A LOOSE wrist pin MAY stop knocking if the plug is shorted out. A loose pin is not a big deal unless you like running at 50MPH all day long, and may not be even then...

Re: Tight wrist pin - If you can move the rod along the crank pin, the pin's not tight. If not enough slop to move on crank, drop rod cap, rotate crank away and move rod around. If it swings and slides in the piston, it's fine. You've already adjusted the rods, so, I'm assuming you did not find #3 to be tight in the piston.

An odd but slightly possible issue would be a wrist pin clamp bolt working loose if it was not cottered correctly

Under the belief that this is a new noise, I'd rule out a bent or twisted rod.
Scott Conger

Tyranny under the guise of law is still Tyranny

NH Full Flow Float Valves
Obsolete carburetor parts manufactured


Topic author
John Dow
Posts: 177
Joined: Tue Jan 29, 2019 10:21 am
First Name: John
Last Name: Dow
* REQUIRED* Type and Year of Model Ts owned: 1923 Touring
Location: Leawood, Ks
MTFCA Number: 32344
Board Member Since: 2015

Re: ILLUSIVE RATTLE CONTINUES

Post by John Dow » Fri Aug 23, 2019 2:02 pm

Scott, Thank you for your help AGAIN!! The rod swings freely and the wrist pin bolt is in place with a cotter key. So how can the pin become loose??


Scott_Conger
Posts: 6428
Joined: Sun Jan 06, 2019 11:18 am
First Name: Scott
Last Name: Conger
* REQUIRED* Type and Year of Model Ts owned: '13, '15, '19, '23
Location: Clark, WY
Board Member Since: 2005

Re: ILLUSIVE RATTLE CONTINUES

Post by Scott_Conger » Fri Aug 23, 2019 2:09 pm

Loose is measured in thousandths of an inch and is a function of wear. In an aluminum piston, it is steel against aluminum, with an oil film supporting the union and running silently...a little wear in the bore of the piston allows movement beyond what the ideal film thickness is of the oil and you get a little knock. If only slightly worn, and running too thin oil, the knock might be heard where a slightly thicker oil, and the oil film will continue to support/cushion the bearing. I like 15/40 in a well run engine and am OK with 10-30 in a new tight engine. Am not trying to start an oil war, just giving you something to think about or try.

This info is for speculation purposes on my end, and perhaps some thinking points for you on your end.
Scott Conger

Tyranny under the guise of law is still Tyranny

NH Full Flow Float Valves
Obsolete carburetor parts manufactured


Topic author
John Dow
Posts: 177
Joined: Tue Jan 29, 2019 10:21 am
First Name: John
Last Name: Dow
* REQUIRED* Type and Year of Model Ts owned: 1923 Touring
Location: Leawood, Ks
MTFCA Number: 32344
Board Member Since: 2015

Re: ILLUSIVE RATTLE CONTINUES

Post by John Dow » Fri Aug 23, 2019 9:47 pm

Thank you Scott. Point well taken.

Post Reply Previous topicNext topic