Steering Issue Has Me Stumped

Discuss all things Model T related.
Forum rules
If you need help logging in, or have question about how something works, use the Support forum located here Support Forum
Complete set of Forum Rules Forum Rules
User avatar

Topic author
Redleg
Posts: 26
Joined: Sun Jan 06, 2019 4:47 pm
First Name: John
Last Name: Neal
* REQUIRED* Type and Year of Model Ts owned: 1925 Roadster Pickup
Location: Alexandria, VA

Steering Issue Has Me Stumped

Post by Redleg » Tue Sep 17, 2019 9:17 pm

Hi folks,

Just got my '25 Roadster up and running, but I have a steering issue that I can't figure out. I've looked in the T-1 manual and searched the forum with no luck - would appreciate some assistance from the team.

With the front end raised, wheels straight, I can only get a quarter turn to the right on the steering wheel before lock. To the left, I get a good three-quarters of a turn before lock. On my one trip around the block, the wheels turn well to the left, but my ability to make right turns is limited. There is no binding in the front end. I suspect some adjustment is needed in the steering gears and/or steering shaft.

BTW, the front end is aligned, caster, camber, and toe-in are good. All front end bushings and have been replaced - the front end is properly tight. I pulled the steering shaft thinking a solution would appear, but nope.

So, I'm stumped and will appreciate you smart fellers' suggestions.

John
John Neal
Virginia
‘25 Roadster Pickup

User avatar

Oldav8tor
Posts: 1928
Joined: Sun Jan 06, 2019 11:39 am
First Name: Tim
Last Name: Juhl
* REQUIRED* Type and Year of Model Ts owned: 1917 Touring
Location: Thumb of Michigan
MTFCA Number: 50297
MTFCI Number: 24810
Board Member Since: 2018

Re: Steering Issue Has Me Stumped

Post by Oldav8tor » Tue Sep 17, 2019 9:37 pm

If your wheels move through a normal range with the pitman arm disconnected the problem must lie in the steering shaft. With the pitman arm disconnected does the steering wheel turn freely? If not it could be binding in the lower bushings but the most likely explanation is some binding between the gears in the quadrant.
1917 Touring
1946 Aeronca Champ
1952 Willys M38a1 Jeep (sold 2023)
1953 Ford Jubilee Tractor


mtntee20
Posts: 527
Joined: Sun Jan 06, 2019 2:51 pm
First Name: Terry & Sharon
Last Name: Miller
* REQUIRED* Type and Year of Model Ts owned: 1920 Center Door, 1920 TTWood cab Farm Truck with cable dump grain bed, 1920 TT C-Cab with express bed, 1927 Wood body Dairy Delivery truck
Location: Westminster, CO
MTFCA Number: 32583
Board Member Since: 2017

Re: Steering Issue Has Me Stumped

Post by mtntee20 » Tue Sep 17, 2019 9:45 pm

I could be whistling out of my patootie but, if I remember correctly, don't the 25s have the "over-center pin" in the gearbox? Thus, if the pitman arm/steering linkage wasn't centered, AND the gearbox was assembled, the over-center pin would stop before full travel of the pitman arm.

I think the problem is in the gearbox. :?:

User avatar

Ruxstel24
Posts: 2345
Joined: Sun Jan 06, 2019 11:25 am
First Name: Dave
Last Name: Hanlon
* REQUIRED* Type and Year of Model Ts owned: 24 Touring car
Location: NE Ohio
MTFCA Number: 50191
Board Member Since: 2018

Re: Steering Issue Has Me Stumped

Post by Ruxstel24 » Tue Sep 17, 2019 9:48 pm

Check if the Pittman arm is straight down with the wheels straight ahead. If not you could have the wrong length drag link...

If ok, I agree with Terry.


Les Schubert
Posts: 1311
Joined: Thu Jan 10, 2019 5:47 pm
First Name: Les
Last Name: Schubert
* REQUIRED* Type and Year of Model Ts owned: 27 roadster 13 touring
Location: Calgary

Re: Steering Issue Has Me Stumped

Post by Les Schubert » Tue Sep 17, 2019 9:48 pm

I think the problem is the drag link. There are various options

User avatar

Henry K. Lee
Posts: 5339
Joined: Sun Jan 06, 2019 11:09 am
First Name: Henry
Last Name: Lee
* REQUIRED* Type and Year of Model Ts owned: Many
Location: South Pittsburg, TN
MTFCA Number: 479
MTFCA Life Member: YES

Re: Steering Issue Has Me Stumped

Post by Henry K. Lee » Tue Sep 17, 2019 9:49 pm

As Tim said, "Look for binding" in those gears. Another suspect is the longer limiting pin backing out or the timing was out when installed. Meaning once upon a time, someone might of had an issue with a worn out pin hole and reposition the triple gears. Something sure ain't right for sure.

Hope this Helps,

Hank


AZTerry
Posts: 86
Joined: Wed Jan 16, 2019 11:18 pm
First Name: Terry
Last Name: Loftus
* REQUIRED* Type and Year of Model Ts owned: 26 Speedster
Location: Phoenix, AZ
MTFCA Number: 7379
MTFCA Life Member: YES

Re: Steering Issue Has Me Stumped

Post by AZTerry » Tue Sep 17, 2019 9:51 pm

Hello John,

My guess is the drag link is may be to long, they came in several lengths over the years:

http://www.mtfca.com/discus/messages/17 ... 1322077087

I would disconnect the drag link at the pitman arm, center the front wheels, then center the steering wheel and measure the approximate length needed.

I hope this helps.

Terry

User avatar

Topic author
Redleg
Posts: 26
Joined: Sun Jan 06, 2019 4:47 pm
First Name: John
Last Name: Neal
* REQUIRED* Type and Year of Model Ts owned: 1925 Roadster Pickup
Location: Alexandria, VA

Re: Steering Issue Has Me Stumped

Post by Redleg » Tue Sep 17, 2019 10:12 pm

Thanks, gents. Most helpful discussion.

With the drag link disconnected, the ball arms travel is limited by the steering gear - more to the right than the left. The problem seems to be there.

John
John Neal
Virginia
‘25 Roadster Pickup

User avatar

Topic author
Redleg
Posts: 26
Joined: Sun Jan 06, 2019 4:47 pm
First Name: John
Last Name: Neal
* REQUIRED* Type and Year of Model Ts owned: 1925 Roadster Pickup
Location: Alexandria, VA

Re: Steering Issue Has Me Stumped

Post by Redleg » Tue Sep 17, 2019 10:13 pm

Thanks, gents. Most helpful discussion.

With the drag link disconnected, the ball arms travel is limited by the steering gear - more to the right than the left. The problem seems to be there.

John
John Neal
Virginia
‘25 Roadster Pickup


Scottio

Re: Steering Issue Has Me Stumped

Post by Scottio » Tue Sep 17, 2019 11:51 pm

My first thought was maybe the steering box. There are three small gears held in place by three pins. One pin that is longer than the others that works as a steering stop. My guess is that the steering shaft is not lined up with the gears properly or the one long pin is in the wrong place. Just my guess of course but it is, at leased, someplace to look.

User avatar

Mark Nunn
Posts: 1105
Joined: Mon Jan 07, 2019 8:01 am
First Name: Mark
Last Name: Nunn
* REQUIRED* Type and Year of Model Ts owned: 1926 Runabout
Location: Bennington, NE
MTFCA Number: 50321
Board Member Since: 2017

Re: Steering Issue Has Me Stumped

Post by Mark Nunn » Wed Sep 18, 2019 1:36 pm

Scottio wrote:
Tue Sep 17, 2019 11:51 pm
My first thought was maybe the steering box. There are three small gears held in place by three pins. One pin that is longer than the others that works as a steering stop. My guess is that the steering shaft is not lined up with the gears properly or the one long pin is in the wrong place. Just my guess of course but it is, at leased, someplace to look.
The long pin is indexed to the key slot for the pitman arm. Moving the long pin would put it 60 degrees from the keyway. The slot in the gearbox for '25, I believe, ends about 55 degrees from vertical. That would let the pitman arm move only one direction.

Maybe the gearbox was replaced and installed upside down. The slot for the locking screw would be at the bottom rather than at the top.

Another possible problem is what I found in my car. My gearbox had 4 broken teeth. If one of them fell into the gearbox, the steering would have locked up. I replaced the gearbox.
col_gear_case.gif

User avatar

DanTreace
Posts: 3299
Joined: Sun Jan 06, 2019 10:56 am
First Name: Dan
Last Name: Treace
* REQUIRED* Type and Year of Model Ts owned: '23 cutoff, '25 touring, '27 touring
Location: North Central FL
MTFCA Number: 4838
MTFCI Number: 115
Board Member Since: 2000
Contact:

Re: Steering Issue Has Me Stumped

Post by DanTreace » Wed Sep 18, 2019 4:04 pm

Remove the drag link from the pitman arm ball. Pull the pitman arm off the steering shaft.

Get in the T and turn the steering wheel to lock one way, and note how the key is aligned.

Now turn it the other way to lock and note location on the shaft of that key .

When you have the steering wheel/shaft at the proper mid-point of wheel travel, the key should be on the back side, center, of the shaft. The key way is indexed to the long 'stop' pinion in the upper end of the steering shaft.

Once you set that, mount the pitman arm over the key. Then place the drag link, should be good working order now.

But, if the steering case cluster was placed upside down, as the groove in the case must be up, when mounted to the steering column, then other issues.

If you don't like how the spider looks on the wheel, pull the wheel and reset it on it's key, for the best wheel position.
The best way is always the simplest. The attics of the world are cluttered up with complicated failures. Henry Ford
Don’t find fault, find a remedy; anybody can complain. Henry Ford

User avatar

Topic author
Redleg
Posts: 26
Joined: Sun Jan 06, 2019 4:47 pm
First Name: John
Last Name: Neal
* REQUIRED* Type and Year of Model Ts owned: 1925 Roadster Pickup
Location: Alexandria, VA

Re: Steering Issue Has Me Stumped

Post by Redleg » Sun Nov 24, 2019 11:01 am

Hi folks,

Just to complete this post for the benefit of others...

I found that the problem was a twisted steering shaft when I removed it again for a closer examination. The keyway at the steering arm should be 180 degrees out from the steering stop pin at the other end - it was not, by about 20 degrees. This allowed oversteering to the left and prevented full travel to the right. Oddly, the shaft shows no sign of trauma and is straight. I replaced it with a reproduction shaft and the problem is resolved. I appreciate everyone's' help in figuring this out. Another T is back on the road!

Thanks,

John
IMG_0179 (002).JPG
John Neal
Virginia
‘25 Roadster Pickup

User avatar

CudaMan
Posts: 2385
Joined: Fri Jan 04, 2019 4:17 pm
First Name: Mark
Last Name: Strange
* REQUIRED* Type and Year of Model Ts owned: 1924 Cut Off Touring (now a pickup)
Location: Hillsboro, MO
MTFCA Number: 30944
MTFCI Number: 23667
Board Member Since: 2013

Re: Steering Issue Has Me Stumped

Post by CudaMan » Sun Nov 24, 2019 11:03 am

Thank you for providing closure on this thread! Glad you found and fixed the problem. :)
Mark Strange
Hillsboro, MO
1924 Cut-off Touring (now a pickup)

User avatar

Oldav8tor
Posts: 1928
Joined: Sun Jan 06, 2019 11:39 am
First Name: Tim
Last Name: Juhl
* REQUIRED* Type and Year of Model Ts owned: 1917 Touring
Location: Thumb of Michigan
MTFCA Number: 50297
MTFCI Number: 24810
Board Member Since: 2018

Re: Steering Issue Has Me Stumped

Post by Oldav8tor » Sun Nov 24, 2019 11:09 am

Wow! 20° of twist? You've got to wonder how that happened...
1917 Touring
1946 Aeronca Champ
1952 Willys M38a1 Jeep (sold 2023)
1953 Ford Jubilee Tractor

User avatar

Bob McDaniel
Posts: 444
Joined: Sun Jan 06, 2019 1:44 pm
First Name: Bob
Last Name: McDaniel
Location: Smithville TN.
MTFCA Number: 28428
Board Member Since: 2007

Re: Steering Issue Has Me Stumped

Post by Bob McDaniel » Sun Nov 24, 2019 12:10 pm

Oldav8tor wrote:
Sun Nov 24, 2019 11:09 am
Wow! 20° of twist? You've got to wonder how that happened...
When superman came to earth he found a model T in the barn to drive to town but someone locked the steering to prevent theft.

Or, people were just a lot stronger back then from the hard work they did every day.
Give an old car guy a barn and he won't throw anything away.

User avatar

Oldav8tor
Posts: 1928
Joined: Sun Jan 06, 2019 11:39 am
First Name: Tim
Last Name: Juhl
* REQUIRED* Type and Year of Model Ts owned: 1917 Touring
Location: Thumb of Michigan
MTFCA Number: 50297
MTFCI Number: 24810
Board Member Since: 2018

Re: Steering Issue Has Me Stumped

Post by Oldav8tor » Sun Nov 24, 2019 4:10 pm

I would have thought the amount of force required to do that would have ripped the screws holding the wheel to the spider right out. It just doesn't compute...
1917 Touring
1946 Aeronca Champ
1952 Willys M38a1 Jeep (sold 2023)
1953 Ford Jubilee Tractor


D Stroud
Posts: 1015
Joined: Sun Jan 06, 2019 10:45 am
First Name: David
Last Name: Stroud
* REQUIRED* Type and Year of Model Ts owned: 1925 Coupe
Location: Mound City, MO 64470
Board Member Since: 2011

Re: Steering Issue Has Me Stumped

Post by D Stroud » Mon Nov 25, 2019 2:51 am

Maybe it wasn't made correctly in the first place? :roll: Dave
1925 mostly original coupe.


Banjoe
Posts: 137
Joined: Sat Mar 23, 2019 8:17 am
First Name: Joe
Last Name: Lucas
* REQUIRED* Type and Year of Model Ts owned: 1927 Tudor
Location: Winnipeg
MTFCA Number: 50498

Re: Steering Issue Has Me Stumped

Post by Banjoe » Mon Nov 25, 2019 8:51 am

Thanks for closing the loop on this challenge, John.

Have been following your challenge and it's great to hear of the positive outcome.

Joe
None of us is as smart as all of us.

Post Reply Previous topicNext topic