They are not available from the vendors any more due to demand.
We (mainly Glen) did the work on a South Bend 10" lathe. Have the thread, taper and keyway done.
Notice taper attachment behind lathe bed.
Making a wide-track rear axle
Forum rules
If you need help logging in, or have question about how something works, use the Support forum located here Support Forum
Complete set of Forum Rules Forum Rules
If you need help logging in, or have question about how something works, use the Support forum located here Support Forum
Complete set of Forum Rules Forum Rules
-
Topic author - Posts: 363
- Joined: Thu Jan 03, 2019 1:38 pm
- First Name: Chris
- Last Name: Brancaccio
- * REQUIRED* Type and Year of Model Ts owned: 1909 Roadster 1915 Coupelet 1923 Coupe 1926 Touring
- Location: Calgary AB
- MTFCA Number: 443
- MTFCA Life Member: YES
- MTFCI Number: 23136
- Board Member Since: 2005
- Contact:
-
Topic author - Posts: 363
- Joined: Thu Jan 03, 2019 1:38 pm
- First Name: Chris
- Last Name: Brancaccio
- * REQUIRED* Type and Year of Model Ts owned: 1909 Roadster 1915 Coupelet 1923 Coupe 1926 Touring
- Location: Calgary AB
- MTFCA Number: 443
- MTFCA Life Member: YES
- MTFCI Number: 23136
- Board Member Since: 2005
- Contact:
Re: Making a wide-track rear axle
Better picture of the taper attachment.
Chris Brancaccio
MTFCA Webmaster
MTFCA Forum Admin
MTFCA Webmaster
MTFCA Forum Admin
-
Topic author - Posts: 363
- Joined: Thu Jan 03, 2019 1:38 pm
- First Name: Chris
- Last Name: Brancaccio
- * REQUIRED* Type and Year of Model Ts owned: 1909 Roadster 1915 Coupelet 1923 Coupe 1926 Touring
- Location: Calgary AB
- MTFCA Number: 443
- MTFCA Life Member: YES
- MTFCI Number: 23136
- Board Member Since: 2005
- Contact:
Re: Making a wide-track rear axle
We started with a 1 1/8 inch shaft, heat treated 4140, 36 inches long.
A short video:
https://www.youtube.com/watch?v=wAnpF6EmXlc
A short video:
https://www.youtube.com/watch?v=wAnpF6EmXlc
Chris Brancaccio
MTFCA Webmaster
MTFCA Forum Admin
MTFCA Webmaster
MTFCA Forum Admin
-
- Posts: 467
- Joined: Sun Jan 06, 2019 2:52 pm
- First Name: John
- Last Name: Guitar
- * REQUIRED* Type and Year of Model Ts owned: 1926 Touring, 1924 Tourer
- Location: Ulladulla
- Board Member Since: 2012
Re: Making a wide-track rear axle
Looks good!
Is this going into a speedster?
Is this going into a speedster?
-
- Posts: 238
- Joined: Sun Jan 06, 2019 12:09 pm
- First Name: Philip
- Last Name: Thompson
- * REQUIRED* Type and Year of Model Ts owned: 1924 touring
- Location: Graham NC
Re: Making a wide-track rear axle
What Rockwell is the stock you are using and where did you get it?. Philip
-
- Posts: 1069
- Joined: Sun Jan 06, 2019 12:18 pm
- First Name: John
- Last Name: Warren
- * REQUIRED* Type and Year of Model Ts owned: 14 Roadster, 25 Pickup , 26 Canadian Touring , and a 24-28 TA race car
- Location: Henderson, Nevada
Re: Making a wide-track rear axle
I think I have a set of wide track axles. The gears are made on the axles
24-28 TA race car, 26 Canadian touring, 25 Roadster pickup, 14 Roadster, and 11AB Maxwell runabout
Keep it simple and keep a good junk pile if you want to invent something
Keep it simple and keep a good junk pile if you want to invent something