FS-CAST ALUM FINNED 3 AND 4 DIP OIL SUMP CASTINGS
-
Topic author - Posts: 1191
- Joined: Sun Jan 06, 2019 11:08 am
- First Name: DAN
- Last Name: MCEACHERN
- * REQUIRED* Type and Year of Model Ts owned: too many. '14 touring, 2 depot hacks, 2 speedsters
- Location: ALAMEDA,CA,USA
FS-CAST ALUM FINNED 3 AND 4 DIP OIL SUMP CASTINGS
THESE CASTINGS ARE 356 T6 ALUMINUM AND WILL FIT 3 AND 4 DIP OIL PANS DEPENDING ON HOW YOU DRILL THEM. On a 4 dip pan, the sump will only cover the 1st 3 dips. Provision inside to attach an oil baffle plate and there are thick side pads on each side for tapped holes for oil lines, or just use for extra oil capacity with a splash lubricated engine.
$125.00 each plus UPS shipping at cost. dmcgearsatyahoodotcom or PM me. Payment by PP or your choice of check or MO.
$125.00 each plus UPS shipping at cost. dmcgearsatyahoodotcom or PM me. Payment by PP or your choice of check or MO.
Last edited by Dan McEachern on Thu Dec 17, 2020 11:50 pm, edited 1 time in total.
-
- Posts: 107
- Joined: Sat Oct 12, 2019 7:56 am
- First Name: Rich
- Last Name: Huggins
- * REQUIRED* Type and Year of Model Ts owned: 1923 touring- 1922 deverley truck -1922 center door
- Location: Maricopa AZ
- MTFCA Number: 50661
- Contact:
Re: FS-CAST ALUM FINNED 3 AND 4 DIP OIL SUMP CASTINGS
will take it need full amount i can pay you to day through zelle
-
Topic author - Posts: 1191
- Joined: Sun Jan 06, 2019 11:08 am
- First Name: DAN
- Last Name: MCEACHERN
- * REQUIRED* Type and Year of Model Ts owned: too many. '14 touring, 2 depot hacks, 2 speedsters
- Location: ALAMEDA,CA,USA
Re: FS-CAST ALUM FINNED 3 AND 4 DIP OIL SUMP CASTINGS
Rich- e-mail sent. thank you. One casting sold, I have a few more if anyone is interested.
-
- Posts: 796
- Joined: Sun Jan 06, 2019 4:14 pm
- First Name: Joseph
- Last Name: Andulics
- * REQUIRED* Type and Year of Model Ts owned: 1926 Fordor, 1926 Truck, 1927 Roadster GOW, RAJO Sprint car
- Location: North Ridgeville, OH
- MTFCA Number: 9766
- Contact:
Re: FS-CAST ALUM FINNED 3 AND 4 DIP OIL SUMP CASTINGS
Good price on a high quality casting. If I was in the need for one I'd jump on it. Finding a good older casting is somewhat difficult and when you do they've often been used and abused.
-
Topic author - Posts: 1191
- Joined: Sun Jan 06, 2019 11:08 am
- First Name: DAN
- Last Name: MCEACHERN
- * REQUIRED* Type and Year of Model Ts owned: too many. '14 touring, 2 depot hacks, 2 speedsters
- Location: ALAMEDA,CA,USA
Re: FS-CAST ALUM FINNED 3 AND 4 DIP OIL SUMP CASTINGS
I still have a few of these available.
-
- Posts: 362
- Joined: Sun Jan 13, 2019 7:53 am
- First Name: Rich
- Last Name: Jesteadt
- * REQUIRED* Type and Year of Model Ts owned: 1914 Touring, 1913 Touring project w. "A" crank shaft
- Location: SE Florida
- MTFCA Number: 50484
- MTFCI Number: 24737
- Contact:
Re: FS-CAST ALUM FINNED 3 AND 4 DIP OIL SUMP CASTINGS
Dan
Does this require spacer plate, and is there any provision for scoup on splash engine with A crank ?
Does this require spacer plate, and is there any provision for scoup on splash engine with A crank ?
-
- Posts: 362
- Joined: Sun Jan 13, 2019 7:53 am
- First Name: Rich
- Last Name: Jesteadt
- * REQUIRED* Type and Year of Model Ts owned: 1914 Touring, 1913 Touring project w. "A" crank shaft
- Location: SE Florida
- MTFCA Number: 50484
- MTFCI Number: 24737
- Contact:
Re: FS-CAST ALUM FINNED 3 AND 4 DIP OIL SUMP CASTINGS
also ,is there space for wish bone clearance
Thanks Rich
Thanks Rich
-
- Posts: 231
- Joined: Mon Jan 14, 2019 4:02 pm
- First Name: Richard
- Last Name: Kemp
- * REQUIRED* Type and Year of Model Ts owned: 1926 TT Tow Truck
- Location: Beavercreek OH
- MTFCA Number: 49768
Re: FS-CAST ALUM FINNED 3 AND 4 DIP OIL SUMP CASTINGS
HI Dan, I would like one. Rich
-
Topic author - Posts: 1191
- Joined: Sun Jan 06, 2019 11:08 am
- First Name: DAN
- Last Name: MCEACHERN
- * REQUIRED* Type and Year of Model Ts owned: too many. '14 touring, 2 depot hacks, 2 speedsters
- Location: ALAMEDA,CA,USA
Re: FS-CAST ALUM FINNED 3 AND 4 DIP OIL SUMP CASTINGS
Yes, the rear of the sump will clear a stock wishbone.
-
- Posts: 174
- Joined: Fri Jan 11, 2019 12:31 pm
- First Name: john
- Last Name: Willams
- * REQUIRED* Type and Year of Model Ts owned: '09 Roadstr, '12 Touring, '26 Fronti Speedster
- Location: Cedar Rapids Iowa
- MTFCI Number: 20566
Re: FS-CAST ALUM FINNED 3 AND 4 DIP OIL SUMP CASTINGS
Dan: Hi From Iowa! I would like one of the pans if available? Thanks John
-
- Posts: 362
- Joined: Sun Jan 13, 2019 7:53 am
- First Name: Rich
- Last Name: Jesteadt
- * REQUIRED* Type and Year of Model Ts owned: 1914 Touring, 1913 Touring project w. "A" crank shaft
- Location: SE Florida
- MTFCA Number: 50484
- MTFCI Number: 24737
- Contact:
Re: FS-CAST ALUM FINNED 3 AND 4 DIP OIL SUMP CASTINGS
Dan
2nd email sent
Rich 561 262 0393
2nd email sent
Rich 561 262 0393
-
- Posts: 273
- Joined: Wed Jan 09, 2019 11:39 am
- First Name: Tom
- Last Name: Elliott
- * REQUIRED* Type and Year of Model Ts owned: 1921 Speedster 1927 speedster
- Location: Portland
- MTFCA Number: 9495
- MTFCA Life Member: YES
- MTFCI Number: 9495
- Board Member Since: 2013
Re: FS-CAST ALUM FINNED 3 AND 4 DIP OIL SUMP CASTINGS
Dan, I hope you have me on your list for a four dip deep sump pan. I need one for my grandson engine that I' working on. Tom
-
- Posts: 362
- Joined: Sun Jan 13, 2019 7:53 am
- First Name: Rich
- Last Name: Jesteadt
- * REQUIRED* Type and Year of Model Ts owned: 1914 Touring, 1913 Touring project w. "A" crank shaft
- Location: SE Florida
- MTFCA Number: 50484
- MTFCI Number: 24737
- Contact:
Re: FS-CAST ALUM FINNED 3 AND 4 DIP OIL SUMP CASTINGS
Dan
Thanks for email reply, If used on splash engine with out anything to circulate oil from sump then it wouldn't serve much value, other than more oil capacity,
Am I correct in my thinking ? better heat transfer with pump to circulate oil.
Thanks for email reply, If used on splash engine with out anything to circulate oil from sump then it wouldn't serve much value, other than more oil capacity,
Am I correct in my thinking ? better heat transfer with pump to circulate oil.
-
Topic author - Posts: 1191
- Joined: Sun Jan 06, 2019 11:08 am
- First Name: DAN
- Last Name: MCEACHERN
- * REQUIRED* Type and Year of Model Ts owned: too many. '14 touring, 2 depot hacks, 2 speedsters
- Location: ALAMEDA,CA,USA
Re: FS-CAST ALUM FINNED 3 AND 4 DIP OIL SUMP CASTINGS
On a splash engine most use an accessory outside oil line like a Ford Faithfull or a hogshead oil line like the one Texas T Parts offers. The extra oil goes to the front of the engine and excess drains thru the dip tray via standoffs into the sump, returning to the flywheel area via a balance pipe/hose to the transmission area.
-
Topic author - Posts: 1191
- Joined: Sun Jan 06, 2019 11:08 am
- First Name: DAN
- Last Name: MCEACHERN
- * REQUIRED* Type and Year of Model Ts owned: too many. '14 touring, 2 depot hacks, 2 speedsters
- Location: ALAMEDA,CA,USA
Re: FS-CAST ALUM FINNED 3 AND 4 DIP OIL SUMP CASTINGS
Tom- PM sent. Dan
-
- Posts: 362
- Joined: Sun Jan 13, 2019 7:53 am
- First Name: Rich
- Last Name: Jesteadt
- * REQUIRED* Type and Year of Model Ts owned: 1914 Touring, 1913 Touring project w. "A" crank shaft
- Location: SE Florida
- MTFCA Number: 50484
- MTFCI Number: 24737
- Contact:
Re: FS-CAST ALUM FINNED 3 AND 4 DIP OIL SUMP CASTINGS
Dan,
Please give more info/ detail about" standoff's"and how to incorporate balance pipe/hose Thanks
P M sent Rich J
Please give more info/ detail about" standoff's"and how to incorporate balance pipe/hose Thanks
P M sent Rich J
-
- Posts: 174
- Joined: Fri Jan 11, 2019 12:31 pm
- First Name: john
- Last Name: Willams
- * REQUIRED* Type and Year of Model Ts owned: '09 Roadstr, '12 Touring, '26 Fronti Speedster
- Location: Cedar Rapids Iowa
- MTFCI Number: 20566
Re: FS-CAST ALUM FINNED 3 AND 4 DIP OIL SUMP CASTINGS
Dan: Hi From Iowa1 I have not heard back to see if I can get one of the pans? Let me know? Thanks John
-
Topic author - Posts: 1191
- Joined: Sun Jan 06, 2019 11:08 am
- First Name: DAN
- Last Name: MCEACHERN
- * REQUIRED* Type and Year of Model Ts owned: too many. '14 touring, 2 depot hacks, 2 speedsters
- Location: ALAMEDA,CA,USA
Re: FS-CAST ALUM FINNED 3 AND 4 DIP OIL SUMP CASTINGS
John- PM sent.
Last edited by Dan McEachern on Sun Mar 14, 2021 12:25 pm, edited 1 time in total.
-
- Posts: 362
- Joined: Sun Jan 13, 2019 7:53 am
- First Name: Rich
- Last Name: Jesteadt
- * REQUIRED* Type and Year of Model Ts owned: 1914 Touring, 1913 Touring project w. "A" crank shaft
- Location: SE Florida
- MTFCA Number: 50484
- MTFCI Number: 24737
- Contact:
Re: FS-CAST ALUM FINNED 3 AND 4 DIP OIL SUMP CASTINGS
Awaiting reply.
-
- Posts: 118
- Joined: Sun Jan 06, 2019 6:05 pm
- First Name: Lester
- Last Name: Husted
- * REQUIRED* Type and Year of Model Ts owned: 20
- Location: Idaho Falls, ID
Re: FS-CAST ALUM FINNED 3 AND 4 DIP OIL SUMP CASTINGS
I will take one for a 4 dip pan. There is no cell phone service for the last 3 weeks to your place. All circuits are busy, try again later. Give me a call
Mike Husted 208-520 4892 Thanks
Mike Husted 208-520 4892 Thanks
-
Topic author - Posts: 1191
- Joined: Sun Jan 06, 2019 11:08 am
- First Name: DAN
- Last Name: MCEACHERN
- * REQUIRED* Type and Year of Model Ts owned: too many. '14 touring, 2 depot hacks, 2 speedsters
- Location: ALAMEDA,CA,USA
Re: FS-CAST ALUM FINNED 3 AND 4 DIP OIL SUMP CASTINGS
All- I've been cleaned out of sump castings for the moment. Rich J. will get the last one. I've had these sitting on the shelf for over two years and thought I would sell a few. The pattern is back at the foundry but I don't have pricing. Most likely the price will increase, as I've been getting significant casting cost increases for the past 6 months. Please send me a PM here or an e-mail to dmcgearsatyahoodotcom if you want a sump casting.
John- you are on my list already. thanks all
John- you are on my list already. thanks all
-
- Posts: 362
- Joined: Sun Jan 13, 2019 7:53 am
- First Name: Rich
- Last Name: Jesteadt
- * REQUIRED* Type and Year of Model Ts owned: 1914 Touring, 1913 Touring project w. "A" crank shaft
- Location: SE Florida
- MTFCA Number: 50484
- MTFCI Number: 24737
- Contact:
Re: FS-CAST ALUM FINNED 3 AND 4 DIP OIL SUMP CASTINGS
Dan
Sent second email
Not urgent don't know if you saw last one.
Thanks Rich J
Sent second email
Not urgent don't know if you saw last one.
Thanks Rich J
-
- Posts: 362
- Joined: Sun Jan 13, 2019 7:53 am
- First Name: Rich
- Last Name: Jesteadt
- * REQUIRED* Type and Year of Model Ts owned: 1914 Touring, 1913 Touring project w. "A" crank shaft
- Location: SE Florida
- MTFCA Number: 50484
- MTFCI Number: 24737
- Contact:
Re: FS-CAST ALUM FINNED 3 AND 4 DIP OIL SUMP CASTINGS
Dan
I'm going to be in south California in June
possibly we could cross paths.
I'm going to be in south California in June
possibly we could cross paths.
-
Topic author - Posts: 1191
- Joined: Sun Jan 06, 2019 11:08 am
- First Name: DAN
- Last Name: MCEACHERN
- * REQUIRED* Type and Year of Model Ts owned: too many. '14 touring, 2 depot hacks, 2 speedsters
- Location: ALAMEDA,CA,USA
Re: FS-CAST ALUM FINNED 3 AND 4 DIP OIL SUMP CASTINGS
Hello All- I have more sump castings available on a limited basis, as there were a few folks that did not get one when I 1st posted these. There was a substantial price increase at the foundry as I expected there would be. The new price is $175.00 each plus UPS shipping. If you have interest you can PM me or send an email to :dmcgearsatyahoo.com.
Thanks, Dan
Thanks, Dan
-
Topic author - Posts: 1191
- Joined: Sun Jan 06, 2019 11:08 am
- First Name: DAN
- Last Name: MCEACHERN
- * REQUIRED* Type and Year of Model Ts owned: too many. '14 touring, 2 depot hacks, 2 speedsters
- Location: ALAMEDA,CA,USA
Re: FS-CAST ALUM FINNED 3 AND 4 DIP OIL SUMP CASTINGS
Two sump castings are spoken for.