MTFCA Forum

kenhaverhill

Yes still using cast iron pistons.valves were done a few years ago .only use couple times a year it is a snowmobile.sat under a barn for who knows how long .uses 1 gal oil for every 6 gals gas ,maybe it's a 2 stroke.hoping to find broken or stuck rings.i know that sometimes people's experience is be...

kenhaverhill

Honing and reringing a 26 tt oil burner,this is a low budget repair on a tt only used a handful of times a year.i bought oversized rings and am looking for thoughts on ring end gap,thanks

kenhaverhill

Does anyone In the new England area have a ruxstell for sale ?

kenhaverhill

How would I find his contact info?

kenhaverhill

Found a Stromberg LF at Hershey,and am looking for the right person to rebuild it

kenhaverhill

I have what appears to be a 1920 fordson F tractor,and was wondering about the color. Mine is orange and I didnt think this was a stock color but its hard to believe someone painted it because there is no other color underneath the orange and there is paint where it seems would have been difficult t...

kenhaverhill

I was wondering where next year's national tour was going to be held and will it be during the summer? Thanks

kenhaverhill

Thanks

kenhaverhill

I am installing what I believe to be a model 160 Stewart speedometer in a 23 touring with 30x3.5 wheels .what is the correct tooth count on the 2 gears at the wheel and is the pivot a 1 to 1 ratio of different? Thanks in advance

kenhaverhill

Need the frames that go around the windshield glass on a 1926 fordor ,2 piece windshield??

kenhaverhill

looking for the drivers seat right side seat hinge for a 23 toudor part number T9520 thanks

kenhaverhill

Sorry for the confusion Glen,when I saw mark I assumed it was your son where as it was on the same add. Ken

kenhaverhill

I was interested in the complete unit for $300 that mark was selling ,maybe a mix up ?

kenhaverhill

Sounds good mark send me an address for the check thanks Ken

kenhaverhill

Mark what do you think it would cost to ship to 01832? I also have a Fastenal a few towns over also thanks ken

kenhaverhill

Pm sent

kenhaverhill

kenhaverhill

Thanks Tom but I think the one I need is a flat plate which mounts to dashboard with large hole in center that speedometer goes threw .

kenhaverhill

Thanks for looking

kenhaverhill

Looking for mounting plate or bezel to mount a model 160 standard speedometer to the dash thanks

kenhaverhill

Hi Bruce, I will take #1 .Let me know how much with postage Ken. I will send a pm

kenhaverhill

I'm not getting the pm?? I got email and sent one back ,I will send money.thanks for follow up

kenhaverhill

I will take them Dave ,going to 01832 .You can send a total and address and i will get the money out thanks Ken

kenhaverhill

Thanks Matt it's a big help ,ken

kenhaverhill

Still hoping someone can provide a picture of the wood door over tool tray on a TT closed cab thanks

kenhaverhill

Thanks George once you said it I got it .still hoping someone has pictures of hinged board under seat

kenhaverhill

I am trying to order floorboards for a TT cab I have and in the Langs catalog it list 2 cabs (closed cab) 1924-25 and 1926-27,and I dont know how to tell the difference . I also could use some pictures of the hinged piece of wood under the seat I dont have much to go by.As always thanks very much in...

kenhaverhill

Just wondering if any for sale ,I'm in Massachusetts

kenhaverhill

Has anyone ever built their own pan straightening table? Are there any parts available from suppliers .are their any plans or schematics available ? Thanks

kenhaverhill

I spoke with the people at scat and they tell me that they have made some changes including a much bigger radius , they feel that even though it looks like enough I still need more radius ground into babbit in block.

kenhaverhill

has anyone run into issues with thrust and a scat crank? I have done engine work with stock cranks with no issues , installing a scat crank for the first time in a 26. block has new babbit,line bored and radius cut on babbit ends. when crank is dropped into block 3rd main journal has no clearance in...

kenhaverhill

Sent you an email mail

kenhaverhill

Does the rearend come with driveshaft and arms ,? Is there a shifter?

kenhaverhill

does anyone have a transmission driven gear puller 5-z-326 for sale ?

kenhaverhill

Looking for a # 53 key not a reproduced but a nice worn original

kenhaverhill

Thanks for the help

kenhaverhill

The valve stems measure .344 ,my concern is how much clearance is needed for correct operation which would give me the correct size ream to buy,thanks again

kenhaverhill

I need some advice , I am installing new valves in a 1920 Fordson tractor. The valves have larger diameter stems and are all that is currently available which is ok my guides are a little worn anyways. the new valves measure 11/32 .344 in diameter and I am not sure what size ream to buy , I dont wan...

MTFCA Forum

Search found 38 matches

Re: Ring end gap

Ring end gap

Wtb ruxstell

Re: LF Stromberg

LF Stromberg

Question for the Fordson Guys

Next year's tour

Re: Some speedometer help please

Some speedometer help please

WTB 26 fordor windshield frames

help,,need seat hinge

Re: WARFORD GEAR BOXES

Re: WARFORD GEAR BOXES

Re: WARFORD GEAR BOXES

Re: WARFORD GEAR BOXES

Re: Restored Stromberg OF Carburetors

Re: Need speedometer part

Re: Need speedometer part

Re: Need speedometer part

Need speedometer part

Re: Rebuilt Holley NH Straight through carbs

Re: FS TT Rear Spring Shackle Bushings

Re: FS TT Rear Spring Shackle Bushings

Re: Still hoping

Still hoping

Re: TT ID help please

TT ID help please

WTB pan straightening table

Pan straightening

Re: scat crank issues

scat crank issues

Re: FS 26-27 ruckstell

Re: FS 26-27 ruckstell

wtb transmission driven gear puller

wtb original #53 key

Re: A question for the machinist in the group

Re: A question for the machinist in the group

A question for the machinist in the group