MTFCA Forum

Larry

Hello Larry,
Attached is a photo of two early bale handles I have.
They are not identical, but very similar in design.
If you think they would work for you, I would take $50 each for any of the handles pictured plus shipping.
Larry

Larry

John,
Sent you a private message with contact information.
Let me know if you have not received it.
Larry

Larry

I have several sets John.
What condition are you looking for?

Larry

Yes Frank. These are bulbs out of an early Baker Electric Car.

Larry

Just wondered if anyone would have a couple original lightbulbs in their stash like the two picture below.

The first bulb is a bayonet base bulb.
120 V 60 W.

The second bulb is a small threaded base.
120V. 60W.

Larry

Hello Chris, I have a very nice pair that have had very little use. They have been properly stored and still pliable with no age cracks. They were used just enough to wear off the nubs but you can still see this very fine angle cut in the treads. I would have to have $150 each for them plus shipping...

Larry

You could tap new threads and use a new bolt.
You would need to remove your tire tube and flap before you did that or flip that portion of the rim off To ensure you did not get any metal shavings in inside your tire.

Larry

Eric,
If I understand Harry correctly, He was concerned about the receiver and this bracket would work for the spade or post. The picture you posted shows the spade and post for hanging the light. The picture Harry posted has a light that would use the spade and not the post.

Larry

Harry,
The bracket is designed for use with either the post or spade.
Attached is an additional photo of the bracket.
Larry

Larry

Harry,
I sent you an email through the form but was unable to post the pictures to it so I will put them here.

Larry

What year L2 are you looking for? There were some variations.
I have some rebuilt years ago and some unrestored ones.

Larry

FS. Miscellaneous gas headlight parts. (sold as a lot) Includes the two burner bases pictured, one elbow, two door latches, one hinge, two igniters, 13 burners, etc.
All four $225 +shipping.

Larry

Larry

Mike, Is this the one you are looking for?

Larry

Larry

Sold,
Thank You,
Larry

Larry

FS. Nice Original Phinney Walker Rim Wind Dash Clock. Last time I looked at it, it did not run, but gave it a half a wind on Tuesday and it has run for over two days. Seems to keep good time, but will probably need cleaned and oiled as it is sensitive to the way it sits. It measures around 2 3/4” in...

Larry

FS. Nice original accessory Electric tail light assembly.
Just cleaned tested and working. Nice original sockets. Contacts cleaned and new bulbs.
The reflector and lenses are in beautiful condition for the age.
Price $150+ shipping.

Larry

Sold.
Thank You,
Larry

Larry

On the outside they are tiered horizontally and on the inside They are scalloped vertically. They are the size of a standard T lens. 8 1/4 inches.

Larry

FS. NOS Original pair of Patterson headlight lenses still in their original box. “Pat. Nov. 25 1919. Great unused condition.
Price $60 + Shipping.

Larry

Nice original rim wind Dash clock made by the “Keyless Auto Clock Co”. It is a rim, wind and rim set clock. Could probably used cleaned and oiled, but it is running. I wound it Friday morning around 7 o’clock and it was still running Sunday afternoon. Nice original face and hands. Price $150 + shipp...

Larry

The original horn bulb,One horn mounting bracket and one reed sold.
The other items are still available.

Larry

For sale a nice variety of early brass model T Horn parts. There are nine horn reeds. One stamped”Rubes”, and one stamped “Peacock”. Various fittings. Three 1915/16 Brass elbows. Two nice original Horn mounting brackets. One original horn bulb with its original threaded adapter and one reproduction ...

Larry

Sold to Phillip.
Payment pending.

Larry

Larry

F.S. Original NOS set of Edmunds and Jones kerosene side and tail lights. Probably used between 1923 and 26 on T’s without electric start. They have their original, never used burner assemblies, and wicks. Never had kerosene in them and never mounted on a car. There is some paint loss on the side li...

Larry

Original 1915 Pennsylvania license plate made by the brilliant manufacturing company Philadelphia PA. Has its original Keystone badge still attached.
Price $125+ Shipping.

Larry

Sold,
Thank You,
Larry

Larry

Unusual set of brass hood latches that came off a late 1912 early 1913 touring car. These latches are the double ear solid brass latches. Some will argue that they only produced the single ear brass in 1912 and switched to the steel double ear in 1913 but these were the original Latches on the car a...

Larry

Sold
Thank You,
Larry

Larry

This is a beautiful original brass Dash clock made by the New Haven clock company, New Haven, Connecticut. The original porcelain face is in beautiful original condition, as is the brass case. The case measures 4 inches in diameter and is sloped at an angle to face the driver when mounted. The mecha...

Larry

Sold
Thank You.
Larry

Larry

Micheal, I would sell the 1912 steering wheel pictured below. It Came off my late 1912 early 1913 touring I restored several years ago. it is in very nice all original condition. There are no cracks or splits in the wood and the original finish is alligatored. I have the original Brass nut as well. ...

Larry

Stephen
I Have an exceptional original set. (side lights, tail light, and headlights) They are correct with original elbow sockets for the headlights. I can get you some pictures tomorrow if you are interested.

Larry

What is a fair price for a nice original one? I know a reproduction one would cost about $400 with shipping.

Larry

I don’t think I have another one but I will check in the morning.
Larry

Larry

Sold .
Thank you,
Larry

Larry

Last three radiator caps have been sold.
Thank you,
Larry

Larry

Larry

Three left. It is my understanding the suppliers are out of these, and have been for a while.

Larry

For sale, new 1917 to 27 chrome radiator caps. Come with a nice neoprene O-ring for a good seal at your radiator neck.
Price $24.95 + shipping

Larry

Sold, Payment Pending.
Thank you.

Larry

Very nice original 1926/27 Ford script horn with its original bracket. Older restoration w/ some paint chips. Has been sitting on the shelf. Just tested and it works perfectly.
$125 + shipping

Larry

Larry

Larry

Larry

For Sale. Large collection of model T service bulletins. There are 80 on the list in the first picture. Those bulletins are in the binder on the right side (2nd picture). The additional stack on the left side of the binder are different service bulletins. I am assuming the majority of those ones are...

Larry

Larry

FS Original Clero Accessory Electric Horn in excellent original working condition. This is the 6 volt model that sounds like the Ford magneto horn only louder. This was a quality accessory horn in its day. (See advertisement attached).
Price $75 + shipping

Larry

Sold,
Thank You!

Larry

Early Ford Model T running board tool box. This is the early small box that measures 11” wide by 9 3/4 “ high and 6 1/2” deep. Very nice solid original condition with its original brass lock and latch stamped “Perfection lift lock patent pend” (No key). Price $225 + shipping IMG_6703.png IMG_6703.png

Larry

Belliott3 wrote: ↑
Mon Mar 04, 2024 9:12 am
Anyone? Still looking

Bill, l saw this post a while back but just have not had a chance to look. Quite sure I have originals. Will look tomorrow.

Larry

Tom,
Which lights are you looking for? The ones that mount directly to the fender and fender bracket or the ones that mount to a headlight bar?

Larry

Hello Tom,
I have the 1913 swivel ((rebuilt), the 60tooth gear, the bracket with bolt, (Bolt not pictured) and a 16 tooth gear.
$250+shipping if you are interested.

Larry

Sold.
Thank you.

Larry

Very nice original 1911/1912 Heinz Coil. Appears to have had very little use. Very nice original master vibrator coil appears to have had very little use if any as well.
$75each + shipping or
$100 for the pair + shipping

Larry

Will PM you late this evening when I get home.

Larry

The core is not good. I used the sides off of this radiator along with the cast radiator support rod, bracket to complete a V radiator that needed those parts.

Larry

The top of the tank, and the face of the tank are still soldered to the core. I would remove those from the core, and could send the tank parts without the core.

Larry

I

Larry

Hello Bill, I have a very nice original 1916 upper tank complete with its original neck. The tank and neck are very nice. Nice threads and quite straight. The back of the tank has the embossed Ford motor company label and the tank number is: 0956943 Reasonably priced if you can use it. Larry IMG_678...

Larry

If it were me, and what you have fits properly, I would remove it and use it as the pattern.

Larry

The Door panels were originally tacked in place. No adhesive was used.

Larry

1.) roll the drivers window down. 2.) remove the four garnish molding trim pieces. 3.) with a putty knife you can pull the side felt channels away from the frame and remove the tacks from inside those felt channels. 4. Place the felt channels back against the frame. 5.) roll the window back up. 6.) ...

Larry

Joshua, You may want to message User name (Russ Furstnow) He is probably the most knowledgeable speedometer person on here. He could tell you if what you have is correct for 1918 and what speedometer head would go with it. He may actually have what you’re looking for. Attached is a photo of the set ...

Larry

Thanks Larry, Let me think about that. I’m trying to figure out how it mounts to the firewall and if the cable enters the speedometer straight or at an angle. Looks like the one you have is missing the angled adapter right? I have the elbow for it. Not sure about the internal part of that elbow tho...

Larry

F.S.Original 1913 Stewart Warner Speedometer and Speedometer drive. The Speedometer is in nice original condition, and I just tested it with a drill. The barrel turns and registers the mileage as it should. I do not know if this drive is the correct drive for the speedometer but the drive does need ...

Larry

If I’m remembering correctly, that would be a model, 102. If so, I have the one pictured below I would sell. It is original and unrestored with the mounting plate and knob. I would take$100 for it if you’re interested. IMG_6315.jpeg I also have a restored one I purchased years ago for my 1918 and wi...

Larry

F.S.Brass Era New Continental 8 Day Dash Clock with Key.
Clock is in beautiful condition. I moved the minute hand forward and it started running. It was still running (1/2 Hr. later) when I left work.
$275+shipping

Larry

Can email of the last three running.

Larry

Thank you Craig!
Much appreciated!
Larry

Larry

F.S. Nice original dash clock made by the Waltham watch company. This is a large dash clock that measures 4 1/4 inches across the face. It still has its original lower dash mounting bracket attached to the stem as well. As with the other clocks I did not wind it, but gave it a little shake and it ra...

Larry

F.S. Nice original keyless auto clock made by the keyless auto clock company. It is a rim, wind and rim set clock. As with the last clock, I have not wound it, but gave it a little shake and it ran for a short time as well.
$150+shipping

Larry

.S. Nice original Phinney-Walker rim wind dash clock. Has always run fine but has sat in a showcase for years and I have not wound it. I did give it a little shake and it ran for about a minute. Will probably need a cleaning. Very nice face glass and case.
$150+shipping

Larry

F.S. Very nice original Brass era dash clock made by the New Haven clock company, New Haven, Connecticut. The case was recently buffed and polished. It is in beautiful condition as is the face, glass and bezel. The clock was running but sat in a showcase for years and it is not running now. The seco...

Larry

F.S. Nice Original Accessory Dash Clocks

Larry

Sold.
Thank You!

Larry

F.S. NOS, Star Accessory Excelerator and pedal pads. They are stamped on the back with their 1925 and 1926 Pat. dates.
$50+shipping

Larry

F.S. Very Nice Original KW Timer with a variety of distributor cam gears. I don’t believe any of these gears came with this timer, but they were all with it when I bought it so I will sell them as a lot.
$100+shipping

Larry

F.S. Nice original Beacon accessory stop tail light with its original Beacon beehive marker lights. All three lenses are in very nice shape and it is complete with its bulbs and sockets. Housing has surface rust but solid and straight. Use as it is a restore. has its original Beacon tag on the top. ...

Larry

For Sale: Nice original extendable truck side mirror with light.
Would be nice on a TT or AA truck. Made by the KD lamp company #103
Has its original glass beehive lens, wiring and mounting bracket.
$85+shipping

Larry

Sold
Thank You,
Larry

Larry

Sold.
Thank You,
Larry

Larry

Still available.

Larry

FS. Beautiful Brass Winged motor meter. Tested and works as it should.
Appears as now.
$110+Shipping

Larry

Nice accessory, articulating spotlight. Made by the inside control spotlight company. Toledo Ohio. This would be really nice on a TT truck or closed car. Tilts up and down or turn side to side. The reflector, lens, and bezel are in beautiful condition. Only one I’ve ever seen. $250+Shipping IMG_6142...

Larry

6V Fire/Police Siren with switch.
Nice Condition
Works Great & Loud
$100 +shipping

Larry

Very Nice accessory stop tail light. Has its original sockets, jeweled top, and very nice lenses.
$250 +shipping

Larry

Thank you, Mark and George.
I think that’s the way I’m doing it.
I usually hit the preview before posting but when I do the pictures are not there. So I’m guessing they need to be resized.
I will give it a try if I get a break this evening or tomorrow.
Thank you for the help.
Larry

Larry

Frank
That actually may be the problem.
I never thought about that.
I’ve switched phones and the photos are probably larger than they were on my last phone.
Thank You,
Larry

Larry

John,
I don’t think I’m doing anything different than I used to but I will look at that again when I get home from work.
Thank You,
Larry

Larry

Does anyone know if the way of attaching pictures to a classified ad has changed? As I have not been able to attach pictures.
Thank You,
Larry

Larry

A question regarding pictures:
I wanted to list some parts for sale, but have not been able to load pictures. Has the way of attaching pictures changed?
Thank You,
Larry

Larry

I have a couple nice model A frames and a large collection of Model A parts for sale if you’re interested. I’m in northeast Ohio and could get one of the a frames to Granger Indiana if interested.
You could PM me if your interested.

Larry

Sold: klaxon Electric 6 volt Ahooga Horn

Larry

The Klaxon horn for sale above is a 6 volt electric horn.

Larry

I have a nice Klaxon Ahooga Horn I would sell. It has been gone through and works perfectly can email video of it working.
Nice loud Ahooga horn $110+shipping.
Was not able to get pictures to load, but I can email them if you are interested.

Larry

Bob,
I can not answer your question as to when these were made.
I have a similar set with the hubs but not the rims and would be interested in them if he decides sell them.
Thank You,
Larry

Larry

Sounds Good Jerry!

Search found 132 matches