Search found 211 matches
- Sat Dec 07, 2019 10:44 pm
- Forum: 2019 General Discussion Forum
- Topic: A new shelter for my Speedster and a little contest...
- Replies: 12
- Views: 704
Re: A new shelter for my Speedster and a little contest...
Beer in the fridge
- Thu Dec 05, 2019 10:53 pm
- Forum: 2019 General Discussion Forum
- Topic: 3 wrench adjustable lifters
- Replies: 6
- Views: 255
Re: 3 wrench adjustable lifters
I use ignition wrenchs the very thin
- Mon Dec 02, 2019 7:35 pm
- Forum: 2019 General Discussion Forum
- Topic: Mounting A Stubborn 30 x 3
- Replies: 32
- Views: 947
Re: Mounting A Stubborn 30 x 3
Had one tge other day had relieve it at valve stem
Took 25 mins total to mount not usual 10-15
Prefer off the car
If i was closer i put it on for you
Took 25 mins total to mount not usual 10-15
Prefer off the car
If i was closer i put it on for you
- Sun Dec 01, 2019 10:00 pm
- Forum: Classifieds - Parts
- Topic: FS model T goodies
- Replies: 0
- Views: 244
FS model T goodies
Moto meter with dogbone cap New $75 never used
Trans cover high volume outlet new never used $25
Brass model G both are very decent cores $45 each
13-4 may west style shackels very usable $40
Brass era head light burner base $25
Make offer on the lot
Dont forget postage
Bob
Jalopyt@yahoo.com
Trans cover high volume outlet new never used $25
Brass model G both are very decent cores $45 each
13-4 may west style shackels very usable $40
Brass era head light burner base $25
Make offer on the lot
Dont forget postage
Bob
Jalopyt@yahoo.com
- Sun Dec 01, 2019 9:52 pm
- Forum: Classifieds - Parts
- Topic: Drum hydraulic brakes setup
- Replies: 0
- Views: 254
Drum hydraulic brakes setup
Newly made 2019 by well lnown T guy who sell high end parts I partly installed this setup and uses 28-7 rearend witch uses safety hibs This set is complete except lines includs 26-7 housings Supply your rear axle internals Asking $1100+ frieght will listen to offers Again these are drum and when ins...
- Mon Nov 25, 2019 11:51 pm
- Forum: Classifieds - Parts
- Topic: FS 15 ribbed pedals set
- Replies: 1
- Views: 249
Re: FS 15 ribbed pedals set
Pedals are sold thanks all who had interest
- Mon Nov 25, 2019 1:18 am
- Forum: Classifieds - Parts
- Topic: FS 15 ribbed pedals set
- Replies: 1
- Views: 249
- Sun Nov 24, 2019 2:32 pm
- Forum: Classifieds - Parts
- Topic: Early BRASS & 13-14 windshields FS
- Replies: 0
- Views: 185
Early BRASS & 13-14 windshields FS
Early unknown brass winshield in very nice shape
Measures 41x26 hinges work smoothly
Asking $550 + shipping
13-14 T complete even support rods to body except glass in excellent orginal shape
Asking $375 + shipping
Contact me at
Jalopyt@yahoo.com
Measures 41x26 hinges work smoothly
Asking $550 + shipping
13-14 T complete even support rods to body except glass in excellent orginal shape
Asking $375 + shipping
Contact me at
Jalopyt@yahoo.com
- Sun Nov 24, 2019 1:57 pm
- Forum: Classifieds - Parts
- Topic: Sold:Ball bearing fourth main "Plus"
- Replies: 3
- Views: 275
Re: For Sale:Ball bearing fourth main "Plus"
Jeff sent email to buy
- Sun Nov 24, 2019 1:55 pm
- Forum: Classifieds - Parts
- Topic: FOR SALE - FULTON AREMORE #2 EXHAUST WHISTLE WITH DUAL FLAP CUTOUT AND FOOT PEDAL
- Replies: 3
- Views: 360
- Sat Nov 16, 2019 7:04 pm
- Forum: Classifieds - Parts
- Topic: WTB 26-7 rear radiouse rods
- Replies: 1
- Views: 112
WTB 26-7 rear radiouse rods
Need a set of good usable rods
To buy or trad
Have 3 cast end rods
Aet of 14-×5 rods trade
Reach me hear or email
Jalopyt@yahoo.com
Thanks
To buy or trad
Have 3 cast end rods
Aet of 14-×5 rods trade
Reach me hear or email
Jalopyt@yahoo.com
Thanks
- Sat Nov 16, 2019 6:27 pm
- Forum: Classifieds - Parts
- Topic: NH Full Flow Float Valves - Available this week
- Replies: 16
- Views: 665
- Fri Nov 15, 2019 10:17 pm
- Forum: 2019 General Discussion Forum
- Topic: Safety Hub Options Preference and Opinions
- Replies: 10
- Views: 631
Re: Safety Hub Options Preference and Opinions
I put in 3 sets on Dan's Mceachern one with stock brakes wood wheels one set on Brid havens brakes with dayton wires And cueently set on Mclaren wire and custom drum brakes After i installed everything o drill the grease cup hole into the hub and bolt and jam nut setup hold it There an O ring and in...
- Fri Nov 15, 2019 10:03 pm
- Forum: Classifieds - Parts
- Topic: Speedster Front Lowering Bracket
- Replies: 13
- Views: 584
Re: Speedster Front Lowering Bracket
Ever have anymore drop me a note
Work well on my prodject
Work well on my prodject
- Fri Nov 15, 2019 10:01 pm
- Forum: Classifieds - Parts
- Topic: NH Full Flow Float Valves - Available this week
- Replies: 16
- Views: 665
Re: NH Full Flow Float Valves - Available this week
Sent an email
- Mon Nov 11, 2019 11:07 pm
- Forum: Classifieds - Parts
- Topic: Reamer 4 Lifter .015 oversized
- Replies: 0
- Views: 190
Reamer 4 Lifter .015 oversized
Almost NEW used on 1 block
Witch didnt need a very fine ream hard cut any material
$55 shipped lower 48
Jalopyt@yahoo.com
Witch didnt need a very fine ream hard cut any material
$55 shipped lower 48
Jalopyt@yahoo.com
- Sat Nov 09, 2019 9:25 pm
- Forum: Classifieds - Parts
- Topic: True T goodies FS
- Replies: 1
- Views: 544
True T goodies FS
Set of ribbed pedals $125+ postage
15 aluminum hogs head $125 + shipping
13-14 nice 12 rivit rear axel cases $195 + frieght
Cast end radiouse rods 3 $60+ frieght
2 Holley G carbs good $50 each
Fox fatman flip 17" steering wheel $325
Always open to offers
Contact me at for pixs
Jalopyt@yahoo.com
Bob
15 aluminum hogs head $125 + shipping
13-14 nice 12 rivit rear axel cases $195 + frieght
Cast end radiouse rods 3 $60+ frieght
2 Holley G carbs good $50 each
Fox fatman flip 17" steering wheel $325
Always open to offers
Contact me at for pixs
Jalopyt@yahoo.com
Bob
- Sun Nov 03, 2019 10:57 pm
- Forum: Classifieds - Parts
- Topic: WtB set of NON DEMOUNTABLE BANDS
- Replies: 4
- Views: 262
Re: WtB set of NON DEMOUNTABLE BANDS
Thanks guys be in touch
- Sun Nov 03, 2019 10:49 pm
- Forum: Classifieds - Parts
- Topic: With front fender irons
- Replies: 2
- Views: 301
Re: With front fender irons
Hank got me covered
- Sun Jul 14, 2019 7:24 pm
- Forum: 2019 General Discussion Forum
- Topic: Valve pins regularly fail
- Replies: 8
- Views: 690
Re: Valve pins regularly fail
Most use to soft or old pins that appear usable
- Fri Jul 12, 2019 2:50 pm
- Forum: 2019 General Discussion Forum
- Topic: New Brassworks Radiator
- Replies: 33
- Views: 2804
Re: New Brassworks Radiator
Many reas oi ns why i had shim the pan at the rear motor mount tilt it a little also shim radiator and make sure the front motor mount is centered good luck
- Wed Jul 10, 2019 12:26 am
- Forum: 2019 General Discussion Forum
- Topic: Berg's has an A+ from me
- Replies: 10
- Views: 1060
Re: Berg's has an A+ from me
Gery a great guy and his radiators are tops
Never had moto meter issue but some cap and meters are heavy
Im glad Gery got his parts issue sorted out
I just wished he made a brassy
Never had moto meter issue but some cap and meters are heavy
Im glad Gery got his parts issue sorted out
I just wished he made a brassy
- Wed Jul 10, 2019 12:21 am
- Forum: Classifieds - Parts
- Topic: Unusual APCO wheel puller
- Replies: 1
- Views: 497
Re: Unusual APCO wheel puller
Make offer
- Wed Jul 10, 2019 12:20 am
- Forum: Classifieds - Parts
- Topic: 2 split rim tools
- Replies: 3
- Views: 436
Re: 2 split rim tools
Make offer
- Wed Jul 10, 2019 12:19 am
- Forum: Classifieds - Parts
- Topic: Splitdorf side drive magneto FS
- Replies: 1
- Views: 318
Re: Splitdorf side drive magneto FS
Sold on facebook model T parts site
- Mon Jul 08, 2019 10:56 pm
- Forum: 2019 General Discussion Forum
- Topic: McLaren Wires and Universal T Drivers --- Years of Tire Trouble
- Replies: 41
- Views: 2342
Re: McLaren Wires and Universal T Drivers --- Years of Tire Trouble
Allen i like that idea on the liner from a 13" tube There is a big variation on tires the on inner seams I seen them so fat you have cut a notch for the stem to so skinny there 3/4 opening On my old wards im currently runnng i have a good 1/4" Overage on the tire and width of the rim Run them till t...
- Mon Jul 08, 2019 10:38 pm
- Forum: 2019 General Discussion Forum
- Topic: Status of New Fuel Tanks
- Replies: 22
- Views: 1751
Re: Status of New Fuel Tanks
Only 1 guy making them and each vendor has wait there turn get a few I faced this issue earlier this year on a round tank I ended up contacting every vendor i could find and bought from only 1 who had one Por 15 a great 2nd choice and just bought a kit to do my old round tanks not holey but crusty I...
- Mon Jul 08, 2019 10:32 pm
- Forum: Classifieds - Parts
- Topic: Splitdorf side drive magneto FS
- Replies: 1
- Views: 318
Splitdorf side drive magneto FS
Aftermarket Splitdorf ( edison) 3 gear side drive mag complete unknown condition of mag but looks nice and tidy in points area
Gear have little wear but very cery usable
Comes as pictured
Asking 650 obo shipping included within 48 ststes elsewhere is at cost or close as estimator goes
Gear have little wear but very cery usable
Comes as pictured
Asking 650 obo shipping included within 48 ststes elsewhere is at cost or close as estimator goes
- Mon Jul 08, 2019 12:19 am
- Forum: Classifieds - Parts
- Topic: 2 split rim tools
- Replies: 3
- Views: 436
2 split rim tools
I have used both with no issues and work great
Not running 21" rims no more
One tool has crack in the arm but never been an issue
Asking $80 for the pair obo includes shipping in lower 48
Not running 21" rims no more
One tool has crack in the arm but never been an issue
Asking $80 for the pair obo includes shipping in lower 48
- Mon Jul 08, 2019 12:15 am
- Forum: Classifieds - Parts
- Topic: Unusual APCO wheel puller
- Replies: 1
- Views: 497
Unusual APCO wheel puller
Unisual Apco wheel puller grabs the spokes not hub cap threads works great i used it twice
Seen only two in 35+ years of model T'ing
$100 includes shipping lower 48 states
Seen only two in 35+ years of model T'ing
$100 includes shipping lower 48 states
- Sun Jul 07, 2019 11:27 pm
- Forum: 2019 General Discussion Forum
- Topic: Need help with Rux lft side shifter
- Replies: 4
- Views: 443
Re: Need help with Rux lft side shifter
Search the forum earlier i post how i made mine out of a worn out hand brake assembly
I couldbuse the same hole as e brake but i made it longer
I couldbuse the same hole as e brake but i made it longer
- Sun Jul 07, 2019 11:22 pm
- Forum: 2019 General Discussion Forum
- Topic: McLaren Wires and Universal T Drivers --- Years of Tire Trouble
- Replies: 41
- Views: 2342
Re: McLaren Wires and Universal T Drivers --- Years of Tire Trouble
This is non demountable clintcher being discussed
Allan no flaps tire beeds are thick and cover the rim completely
21" tires use 32-35psi clintcher use 55 to 65 psi
If you dont run right pressure on clintcher the tire will slip in the rim and i DONT mean check them once a year i check mine monthly
Allan no flaps tire beeds are thick and cover the rim completely
21" tires use 32-35psi clintcher use 55 to 65 psi
If you dont run right pressure on clintcher the tire will slip in the rim and i DONT mean check them once a year i check mine monthly
- Sun Jul 07, 2019 12:14 am
- Forum: 2019 General Discussion Forum
- Topic: Fuel lines
- Replies: 22
- Views: 1459
Re: Fuel lines
Car never runs rough like turning off the key
Of stan howel rebiuld and yes vinton tipped
Im switching back once get nh finished up
See it thats the issue
Of stan howel rebiuld and yes vinton tipped
Im switching back once get nh finished up
See it thats the issue
- Sun Jul 07, 2019 12:07 am
- Forum: 2019 General Discussion Forum
- Topic: McLaren Wires and Universal T Drivers --- Years of Tire Trouble
- Replies: 41
- Views: 2342
Re: McLaren Wires and Universal T Drivers --- Years of Tire Trouble
I have nought a set from Mike at vintage wire wheel
Have had no bbn issues coming up on 200+ miles on them they are powder coated
60 to 65 psi rubber stem tubes ward riversides no flaps
I been watching my tubes as i have heard of this issue
With early sets
Have had no bbn issues coming up on 200+ miles on them they are powder coated
60 to 65 psi rubber stem tubes ward riversides no flaps
I been watching my tubes as i have heard of this issue
With early sets
- Sat Jul 06, 2019 3:45 pm
- Forum: 2019 General Discussion Forum
- Topic: Fuel lines
- Replies: 22
- Views: 1459
Re: Fuel lines
Scott true One correction i put 3/4" meant to say 3/8" heehee My stromberg OF fills on the bottom side of the float bowl and rebiulding an NH try befor i change the fuel line Randon fuel starvation happen when pulling up to a stop Not at speed witch seems odd since the foat is as high as i can go Im...
- Fri Jul 05, 2019 1:56 am
- Forum: Classifieds - Parts
- Topic: OT Wayne 615 visable gas pump
- Replies: 1
- Views: 462
OT Wayne 615 visable gas pump
Have a complete wayne 615 visiable gas pump needs restoration
Many New parts skins are new and powder coated yellow
Only missing a topper
Asking 1400 obo
Many New parts skins are new and powder coated yellow
Only missing a topper
Asking 1400 obo
- Fri Jul 05, 2019 1:50 am
- Forum: 2019 General Discussion Forum
- Topic: Fuel lines
- Replies: 22
- Views: 1459
Re: Fuel lines
I use 1/4" brake line with good results but since i pit on the of seems fuel starvation is happening So going run a larger line 5/16" or 3/8" Down 3/4 of the way to the carb and 1/4" line rest of the way? I not fan fuel pump running 40-45 keeps up just fine but when o drive in traffic seems starve b...
- Fri Jul 05, 2019 1:35 am
- Forum: 2019 General Discussion Forum
- Topic: Odds of getting stolen
- Replies: 23
- Views: 1619
Re: Odds of getting stolen
Im 35 years old owning and driving model Ts i had 1 radiator cap stollen in 1993
I dont tour with grouos and leave my car unattended while eating or shopping
Only seriouse mishap or issue when i drove my T to college late 1987-89 it get toilet papered often
I dont tour with grouos and leave my car unattended while eating or shopping
Only seriouse mishap or issue when i drove my T to college late 1987-89 it get toilet papered often
- Fri Jun 28, 2019 10:17 pm
- Forum: 2019 General Discussion Forum
- Topic: Trying reach Ralph Cordell of Arizona
- Replies: 5
- Views: 552
Re: Trying reach Ralph Cordell of Arizona
Thanks much Tomy
- Thu Jun 27, 2019 2:44 pm
- Forum: 2019 General Discussion Forum
- Topic: Trying reach Ralph Cordell of Arizona
- Replies: 5
- Views: 552
Re: Trying reach Ralph Cordell of Arizona
Orginal Smith dont have one nor do i know anyone who doese
- Thu Jun 27, 2019 2:38 pm
- Forum: 2019 General Discussion Forum
- Topic: Radiators
- Replies: 10
- Views: 1045
Re: Radiators
Berg's had a parts supply issue earlier this year but not sure its been resolved or not
Know 2 guys getting black era radiators from brassworks
And know 1 guy getting a brassy from them as well
Know 2 guys getting black era radiators from brassworks
And know 1 guy getting a brassy from them as well
- Tue Jun 25, 2019 11:19 pm
- Forum: 2019 General Discussion Forum
- Topic: Rushmore Searchlight
- Replies: 9
- Views: 997
Re: Rushmore Searchlight
Not using gas to light i bought concave parabolic mirror
From science teacher supply
From science teacher supply
- Tue Jun 25, 2019 2:59 pm
- Forum: 2019 General Discussion Forum
- Topic: Trying reach Ralph Cordell of Arizona
- Replies: 5
- Views: 552
Trying reach Ralph Cordell of Arizona
Ralph and Ann Cordell (sp)of Arizona oregon or Nevada
He is a long time friend and avid model T'er
He had an item at Bakersfield swap this year 2019 if you know him please send me contact info or ask for mine so he can contact me
Thanks in advance
Nv bob middleton
Jalopyt@yahoo.com
He is a long time friend and avid model T'er
He had an item at Bakersfield swap this year 2019 if you know him please send me contact info or ask for mine so he can contact me
Thanks in advance
Nv bob middleton
Jalopyt@yahoo.com
- Sun Jun 23, 2019 1:38 pm
- Forum: 2019 General Discussion Forum
- Topic: "New" Ricardo HC head - WOW!!
- Replies: 19
- Views: 2090
Re: "New" Ricardo HC head - WOW!!
Admin jeff head is a Ricardo not waukesha ricardo
Compresstion is about 6.5to1
Compresstion is about 6.5to1
- Mon Jun 17, 2019 12:39 am
- Forum: 2019 General Discussion Forum
- Topic: Changing clincher tires with flaps
- Replies: 32
- Views: 2173
Re: Changing clincher tires with flaps
I have stopped using flaps and pay more attention to tire pressure 50psi low as they go and not flat since Use baby powder in tire and mount both beeds at the same time with tube just aired enough keep it round 1 hour work 4 new tires tube mounted I mounted rhese for a friend having trouble and like...
- Mon Jun 17, 2019 12:28 am
- Forum: 2019 General Discussion Forum
- Topic: Removable ear bands in 1915?
- Replies: 18
- Views: 1318
Re: Removable ear bands in 1915?
If you do you want use the teens hogs head as stated the clutch shaft is supported better
Aluninum covers are easy pull and replace so why would you need them
Just my 2 cents
Aluninum covers are easy pull and replace so why would you need them
Just my 2 cents
- Sat Jun 15, 2019 11:40 pm
- Forum: 2019 General Discussion Forum
- Topic: Selling a car these days...
- Replies: 7
- Views: 1180
Re: Selling a car these days...
Bought and sold cars of the internet this year Money transfer wire transfer to a savings account that is just that this account has no links to any other accounts hassle free both ways just had go bank each time Bought the car got it home feel happy as the seller was honest The other car had many is...
- Sun Jun 09, 2019 11:46 pm
- Forum: Classifieds - Parts
- Topic: Carb sale see ad
- Replies: 1
- Views: 535
Re: Carb sale see ad
A few have sold have more Kingston and Holley Gs best offer
- Sun Jun 09, 2019 11:32 am
- Forum: Classifieds - Parts
- Topic: Fs distributors
- Replies: 5
- Views: 848
Re: Fs distributors
Bosch has been spoken for thanks Tom and MTFCA
- Sun Jun 09, 2019 10:38 am
- Forum: Classifieds - Parts
- Topic: Fs distributors
- Replies: 5
- Views: 848
Re: Fs distributors
Send world wide at cost
- Sat Jun 08, 2019 11:44 pm
- Forum: 2019 General Discussion Forum
- Topic: Rootlieb Inc. sheetmetal products
- Replies: 6
- Views: 1140
Re: Rootlieb Inc. sheetmetal products
Done 2 complete speedster kits many fenders and even had them make a custom hood for my 29 model A cabrolet i owned few years back
Yes very happy with everything
Tom Rootlieb is very nice guy even gave me a full tour of his operation
Yes very happy with everything
Tom Rootlieb is very nice guy even gave me a full tour of his operation
- Sat Jun 08, 2019 11:40 pm
- Forum: 2019 General Discussion Forum
- Topic: Spindle bushing removal made easier
- Replies: 8
- Views: 1019
Re: Spindle bushing removal made easier
That is how you use the tool correctly wedge it open
If not your not using correctly
If not your not using correctly
- Sat Jun 08, 2019 11:28 pm
- Forum: 2019 General Discussion Forum
- Topic: “New” Ricardo head - head bolt length??
- Replies: 9
- Views: 658
Re: “New” Ricardo head - head bolt length??
Had to cross this same bridge use high head bolts
- Sat Jun 08, 2019 6:52 pm
- Forum: Classifieds - Parts
- Topic: Fs distributors
- Replies: 5
- Views: 848
Fs distributors
1 delco
1 bosch
Both have all gears and with new condenser should be ok i run coils so these where removed and sat around here for several years $100 each or offer
1 bosch
Both have all gears and with new condenser should be ok i run coils so these where removed and sat around here for several years $100 each or offer
- Sat Jun 08, 2019 6:49 pm
- Forum: Classifieds - Parts
- Topic: Carb sale see ad
- Replies: 1
- Views: 535
Carb sale see ad
Brass body holley G steel top and bowl runs needs gaskets at bolw $65 4 steel holley G rebiulable cores 95% there all $50 2 brass kingston 1915-16 both $60 Speedster zoom carbs Zenith brass D4 good complete $65 Zenith brass looks like a D4 but larger 1 stromberg and what i think carter?? $40 All plu...
- Wed Jun 05, 2019 12:13 pm
- Forum: Classifieds - Parts
- Topic: Wtb door latch exstention
- Replies: 1
- Views: 255
Wtb door latch exstention
This ou s an accessory the attaches to the door latch raise it up
I have only see a few on cars
Just need 1
I have only see a few on cars
Just need 1
- Sun Jun 02, 2019 11:13 pm
- Forum: 2019 General Discussion Forum
- Topic: Auburn, CA Motherlode swap meet report
- Replies: 22
- Views: 1845
Re: Auburn, CA Motherlode swap meet report
Admin jeff your welcome
I shared a both and brought things to sell
Totaly forgot the forum gathering but everyone i know here never brought it up sorry
Againg it was great event and one not to miss on the west coast
I shared a both and brought things to sell
Totaly forgot the forum gathering but everyone i know here never brought it up sorry
Againg it was great event and one not to miss on the west coast
- Sun Jun 02, 2019 6:51 pm
- Forum: 2019 General Discussion Forum
- Topic: Mother Lode Swap Meet - Changes
- Replies: 6
- Views: 828
Re: Mother Lode Swap Meet - Changes
Dan sorry i missed you was great meet
Didnt buy much nut sold all that I brought early
Witch was great
Saw lot old friends made afew new ones
Thanks much MLMFCA you put on a great swap
Didnt buy much nut sold all that I brought early
Witch was great
Saw lot old friends made afew new ones
Thanks much MLMFCA you put on a great swap
- Tue May 28, 2019 10:57 pm
- Forum: 2019 General Discussion Forum
- Topic: Best solvent for dissolving epoxy putty
- Replies: 9
- Views: 1049
Re: Best solvent for dissolving epoxy putty
Wow may is almost over looking back on this month been busy
Mounted 15 clintcher tires
Rebiult standard rear axel
Put in new gas tank
1 band job
Rebiult holley NH
Rebiult coil box
Put on new lined brakes
Sold a T
Drove the new T
Hopefuly finish up a valve job drive new T more
Mounted 15 clintcher tires
Rebiult standard rear axel
Put in new gas tank
1 band job
Rebiult holley NH
Rebiult coil box
Put on new lined brakes
Sold a T
Drove the new T
Hopefuly finish up a valve job drive new T more
- Tue May 28, 2019 10:47 pm
- Forum: 2019 General Discussion Forum
- Topic: Model T club meeting entertainment ideas
- Replies: 4
- Views: 552
Re: Model T club meeting entertainment ideas
We have a show and tell or tech talk 5-10 mins or so or part tool We also have a project update 5 min limit But most fun is having a selected member who is adked ofcourse on a chat of related hobbies I did one on license plates for my state Keep topics 5-20 mins and lite hearted passing around items...
- Sun May 26, 2019 2:26 pm
- Forum: 2019 General Discussion Forum
- Topic: Fiber tack strips
- Replies: 1
- Views: 353
Fiber tack strips
I bought new fiber tack strip anyone ever installed one my wood all but gone
On my 14
Also
Is Ford wood in Utal still in business phone has message send emails but never heard back
On my 14
Also
Is Ford wood in Utal still in business phone has message send emails but never heard back
- Sun May 26, 2019 2:23 pm
- Forum: 2019 General Discussion Forum
- Topic: Ball bearings for steel hub fan?
- Replies: 5
- Views: 597
Re: Ball bearings for steel hub fan?
I bought one for my 18 but sold the car. Will make you a seal of a deal
I use ball bearing hub in my brass hub fans and love them set it and forget it
I use ball bearing hub in my brass hub fans and love them set it and forget it
- Fri May 24, 2019 11:03 pm
- Forum: 2019 General Discussion Forum
- Topic: Mother Lode Swap Meet - Changes
- Replies: 6
- Views: 828
Re: Mother Lode Swap Meet - Changes
Will hit town saturday afternoon
Chase woman drink beer and see lots of friends waiting for the sw as p
Chase woman drink beer and see lots of friends waiting for the sw as p
- Thu May 23, 2019 11:28 pm
- Forum: Classifieds - Parts
- Topic: Ricardo head FS
- Replies: 0
- Views: 461
Ricardo head FS
Ricardo head have run this head with no trouble
Pat date 1923
Asking $425 obo
Contact me via
Jalopyt@yahoo.com
Pat date 1923
Asking $425 obo
Contact me via
Jalopyt@yahoo.com
- Thu May 23, 2019 11:23 pm
- Forum: Classifieds - Parts
- Topic: Atlas Steel spoke wheel set FS
- Replies: 0
- Views: 467
Atlas Steel spoke wheel set FS
Full set size 30x3.5 demountable TUBE steel spoke wheels uses wood wheel hubs
Rims are smooth no sharp edges has all keepers and bolts
Have a rim for a spare
tires not included
Asking $1250+shipping
Can deliver to Auburn swap
Contact me
Jalopyt@yahoo.com
Rims are smooth no sharp edges has all keepers and bolts
Have a rim for a spare
tires not included
Asking $1250+shipping
Can deliver to Auburn swap
Contact me
Jalopyt@yahoo.com
- Tue May 21, 2019 12:04 am
- Forum: 2019 General Discussion Forum
- Topic: Need hauling sparks Nv to Spokane Wa
- Replies: 0
- Views: 186
Need hauling sparks Nv to Spokane Wa
I nice gentelmen from Canada has bought his first T And looking for a ride to pacific north west 2nd he need get intouch with T folks in spokane to British Columbia Canada to mentor him If you or know of a groupwho can help him along Please contact me so i can pass along your info Thanks in advance ...
- Sun May 19, 2019 10:15 am
- Forum: 2019 General Discussion Forum
- Topic: Shiny Carburetors
- Replies: 8
- Views: 1061
Re: Shiny Carburetors
I have used high temp clear engine spray paint on other brass fittings and carbs
This clear resists oil grease and gas
But like Steve Heff states ciated brass looks just like coated brass and over time wears and looks nasty
This clear resists oil grease and gas
But like Steve Heff states ciated brass looks just like coated brass and over time wears and looks nasty
- Sun May 19, 2019 10:08 am
- Forum: Classifieds - Parts
- Topic: IWtb Low Head
- Replies: 6
- Views: 639
Re: IWtb Low Head
Terry thanks for looking
Dan you are correct
Dan you are correct
- Fri May 17, 2019 10:13 pm
- Forum: 2019 General Discussion Forum
- Topic: What timer do you use
- Replies: 43
- Views: 2700
Re: What timer do you use
Hoarder
I could use a spare if that day ever comes
I could use a spare if that day ever comes
- Fri May 17, 2019 10:07 pm
- Forum: 2019 General Discussion Forum
- Topic: Scandinavian Bands soaking or not?
- Replies: 5
- Views: 670
Re: Scandinavian Bands soaking or not?
Jim
I used to now put them in dry
Add a quart of oil over them after installed
Never had an issue in 20 sets doing it this way
Oh dint drain extra oil out yhe top pet cock
I used to now put them in dry
Add a quart of oil over them after installed
Never had an issue in 20 sets doing it this way
Oh dint drain extra oil out yhe top pet cock
- Fri May 17, 2019 7:46 pm
- Forum: Classifieds - Parts
- Topic: IWtb Low Head
- Replies: 6
- Views: 639
IWtb Low Head
I have a friend that has a 13 T with a high head
Befor i pay have it milled 3/16" wanted see if a good low head can be found
Thanks
Befor i pay have it milled 3/16" wanted see if a good low head can be found
Thanks
- Fri May 17, 2019 7:32 pm
- Forum: 2019 General Discussion Forum
- Topic: What timer do you use
- Replies: 43
- Views: 2700
Re: What timer do you use
Been work on Ts 35+ years never heard of a timer box? Had great service from Anderson and the New Day although for a period new days where JUNK but seems tobe corrected now Anderson only requires little contact lube each year and ND only a wipe out to clean Most people issues is not the time but coi...
- Thu May 16, 2019 4:43 pm
- Forum: Classifieds - Parts
- Topic: Hop up goodies
- Replies: 2
- Views: 816
Re: Hop up goodies
Contact to
Jalopyt@Yahoo.com
Jalopyt@Yahoo.com
- Thu May 16, 2019 1:51 am
- Forum: Classifieds - Parts
- Topic: Hop up goodies
- Replies: 2
- Views: 816
Hop up goodies
4 maclaren wire wheel NEW powder coated medium blue
New 2019 asking $3200+ post
4 valva Rajo currently on running car comes with intake and windfield carb ready to install and zoom
Includes fuel pump $3400
Can send pics and ofcourse will listen to offers
New 2019 asking $3200+ post
4 valva Rajo currently on running car comes with intake and windfield carb ready to install and zoom
Includes fuel pump $3400
Can send pics and ofcourse will listen to offers
- Tue May 14, 2019 12:52 am
- Forum: 2019 General Discussion Forum
- Topic: ruckstell shifting
- Replies: 7
- Views: 707
Re: ruckstell shifting
If the geometry is visualy that far wrong you spot it on install
Heres my left hand shift put the front pivot same location as stock center shift L&R except 4" closer
Heres my left hand shift put the front pivot same location as stock center shift L&R except 4" closer
- Mon May 13, 2019 12:34 am
- Forum: 2019 General Discussion Forum
- Topic: Auburn Mother Lode Swap Meet
- Replies: 7
- Views: 927
Re: Auburn Mother Lode Swap Meet
I be there if you know me say howdy if dont say hi
After my first spin time for pie coz only got 1 eye
I be rollin saturday night and the party will start befor 1st light
After my first spin time for pie coz only got 1 eye
I be rollin saturday night and the party will start befor 1st light
- Mon May 13, 2019 12:27 am
- Forum: 2019 General Discussion Forum
- Topic: Lubricants, what do you use?
- Replies: 21
- Views: 1546
Re: Lubricants, what do you use?
85/140 my gear lube ruckstel included
Oil whats ever cheapest as long as it is not
Synthetic
Oil whats ever cheapest as long as it is not
Synthetic
- Mon May 13, 2019 12:20 am
- Forum: 2019 General Discussion Forum
- Topic: Steering Gear Case Plating
- Replies: 6
- Views: 634
Re: Steering Gear Case Plating
Surveying
Cant find a shop drop me a note my plater here is old school and will listen and follow my instructions
Got alot of guys in central California giving my stuff
And comes back impressive
Cant find a shop drop me a note my plater here is old school and will listen and follow my instructions
Got alot of guys in central California giving my stuff
And comes back impressive
- Thu May 09, 2019 12:00 am
- Forum: 2019 General Discussion Forum
- Topic: Do I have a broken crankshaft?
- Replies: 14
- Views: 1734
Re: Do I have a broken crankshaft?
I have driven this car and passed for 14 that was for sale as well
Erik is great T guy rather see T's on the road his shop is amazing
This what makes the hobby great
Erik is great T guy rather see T's on the road his shop is amazing
This what makes the hobby great
- Fri May 03, 2019 2:54 pm
- Forum: Classifieds - Parts
- Topic: 18 roadster on dayton wires FS
- Replies: 6
- Views: 1420
Re: 18 roadster on dayton wires FS
Car has sold
- Mon Apr 29, 2019 11:31 pm
- Forum: 2019 General Discussion Forum
- Topic: Rims and Tires
- Replies: 26
- Views: 2007
Re: Rims and Tires
By 1921 for was using 30x3.5 demountables all around
My friends 17 centerdoor has demountables all around
My friends 17 centerdoor has demountables all around
- Sun Apr 28, 2019 11:27 pm
- Forum: Classifieds - Parts
- Topic: Side mount spare mounts in brass FS
- Replies: 0
- Views: 305
Side mount spare mounts in brass FS
Set to hold a tire on the running board
These where cast and need to be finished
$75 shipped in connected 48
13-14 sidelight brackets match set 1 is repo
$45 shipped
Contact me
Jalopyt@yahoo.com
These where cast and need to be finished
$75 shipped in connected 48
13-14 sidelight brackets match set 1 is repo
$45 shipped
Contact me
Jalopyt@yahoo.com
- Sun Apr 28, 2019 6:06 pm
- Forum: Classifieds - Parts
- Topic: 16 motor running
- Replies: 4
- Views: 1104
Re: 16 motor running
16 motor sold
- Sat Apr 27, 2019 12:44 pm
- Forum: Classifieds - Parts
- Topic: Brass side spare bracket 13-14 side light brackets
- Replies: 1
- Views: 368
Brass side spare bracket 13-14 side light brackets
Set brass spare tire brackets newer cast
Need to be finished $75 includes shipping in. 48 states
13-14 side light brackets match pair $45 includes shipping in 48 states
Will ship but extra postage needed
Also feel free make me an offer
Contact me at
Jalopyt@yahoo.com
Need to be finished $75 includes shipping in. 48 states
13-14 side light brackets match pair $45 includes shipping in 48 states
Will ship but extra postage needed
Also feel free make me an offer
Contact me at
Jalopyt@yahoo.com
- Sat Apr 27, 2019 1:43 am
- Forum: Classifieds - Parts
- Topic: 18 roadster on dayton wires FS
- Replies: 6
- Views: 1420
Re: 18 roadster on dayton wires FS
Listed on Ebay or will sell here $9k original radiator as bergs order was canceled since unknown back order delay
- Wed Apr 24, 2019 11:07 pm
- Forum: Classifieds - Parts
- Topic: FOR SALE - BOSCH DU4 MAGNETO
- Replies: 1
- Views: 483
Re: FOR SALE - BOSCH DU4 MAGNETO
Spin it again Jay
- Wed Apr 24, 2019 12:31 am
- Forum: Classifieds - Parts
- Topic: 16 motor running
- Replies: 4
- Views: 1104
Re: 16 motor running
hows $500 sound obo
- Tue Apr 23, 2019 12:22 pm
- Forum: Classifieds - Parts
- Topic: Crank Handle FS
- Replies: 16
- Views: 1663
Re: Crank Handle FS
15-22 used this style
11-14 used aluminum handle
But L piece was the same
11-14 used aluminum handle
But L piece was the same
- Mon Apr 22, 2019 8:03 pm
- Forum: Classifieds - Parts
- Topic: 18 roadster on dayton wires FS
- Replies: 6
- Views: 1420
Re: 18 roadster on dayton wires FS
I had lots of interest in daytons and they can be bought
Out right as i do have a set of Atlas steel demountables
10 feet away these look like wood wheels
Out right as i do have a set of Atlas steel demountables
10 feet away these look like wood wheels
- Sun Apr 21, 2019 12:52 pm
- Forum: 2019 General Discussion Forum
- Topic: Quality Inner Tubes
- Replies: 18
- Views: 1709
Re: Quality Inner Tubes
Ruxstel24
Summit if your irder over $99 free shipping well thats what ive got.
They also carry the inner timken front bearing and seal both races plus paints polishes oils and shop supplies so easy get it up to free shipping
Summit if your irder over $99 free shipping well thats what ive got.
They also carry the inner timken front bearing and seal both races plus paints polishes oils and shop supplies so easy get it up to free shipping
- Sun Apr 21, 2019 12:42 pm
- Forum: 2019 General Discussion Forum
- Topic: MTFCA safety check list sheet
- Replies: 4
- Views: 473
Re: MTFCA safety check list sheet
Erik yes and I hope other groups and clubs have or do something simular The local group is growing and i try do seminar once a year done one on tires mounting demounting care and another one on bands/ trans and now safety check/ inspection and basic servicing. We have serveral new T owners and sever...
- Sun Apr 21, 2019 2:01 am
- Forum: 2019 General Discussion Forum
- Topic: MTFCA safety check list sheet
- Replies: 4
- Views: 473
Re: MTFCA safety check list sheet
Keith thanks
- Sat Apr 20, 2019 11:03 pm
- Forum: 2019 General Discussion Forum
- Topic: MTFCA safety check list sheet
- Replies: 4
- Views: 473
MTFCA safety check list sheet
Years ago MTFCA had a safety inspection sheet this was for cars that went on national tours was printed in VF a few times anyone have a copy they can email me
I doing a safety check seminar for the lical T club and wanted use ine
Thanks in advance
I doing a safety check seminar for the lical T club and wanted use ine
Thanks in advance
- Sat Apr 20, 2019 10:53 pm
- Forum: 2019 General Discussion Forum
- Topic: Quality Inner Tubes
- Replies: 18
- Views: 1709
Re: Quality Inner Tubes
Hartford tubes just bought 5 from Summit racing
All fresh nice and thick rubber stem 30x3.5
21" tubes i get there as well but get there 20" ones
Realy thick and always been fresh feeling rubber
30x3.5 was $22 a tube 21" was around $15
All fresh nice and thick rubber stem 30x3.5
21" tubes i get there as well but get there 20" ones
Realy thick and always been fresh feeling rubber
30x3.5 was $22 a tube 21" was around $15
- Sat Apr 20, 2019 10:45 pm
- Forum: 2019 General Discussion Forum
- Topic: Financing a Model T
- Replies: 23
- Views: 2146
Re: Financing a Model T
Credit union mightbut highly unlikely They did once on a model A but i had to have a co-signer As wrll as them being on the title. Depending on the car price i suggest a private loan company. They loan you 10k if you have decent credit or property interest is higher then the bank but usualy easier m...
- Sat Apr 20, 2019 10:35 pm
- Forum: 2019 General Discussion Forum
- Topic: Blasphemy - oiler versus zerk
- Replies: 8
- Views: 945
Re: Blasphemy - oiler versus zerk
Put zerks in grease em now and then you be happy
- Sat Apr 20, 2019 10:30 pm
- Forum: 2019 General Discussion Forum
- Topic: Spindle Threads question
- Replies: 16
- Views: 1460
Re: Spindle Threads question
Left side or drivers side on common US cars and TTs are right hand thread sould not change it much
If the are is the same style
If the are is the same style
- Thu Apr 18, 2019 11:30 pm
- Forum: Classifieds - Parts
- Topic: FOR SALE - DUPLEX AUTO SIGNAL BRAKE AND RUNNING LIGHT SET MOUNTS ON BOTH SIDES OF WINDSHIELD NEW OLD STOCK
- Replies: 1
- Views: 508
- Wed Apr 17, 2019 7:33 pm
- Forum: Classifieds - Parts
- Topic: 18 roadster on dayton wires FS
- Replies: 6
- Views: 1420
18 roadster on dayton wires FS
Cant post in vehicals for sale so i list here 1918 roadster correction Located Reno Nv Dayton wire wheels Ruckstel Low head Floating hubs Good running car starts easy Uphostery & top very nice Paint fair as are the tires holley G carb New tubes spare engine that runs needs hog head rebiult New Berg'...
- Wed Apr 17, 2019 7:30 pm
- Forum: Classifieds - Vehicles
- Topic: T wanted
- Replies: 21
- Views: 6010
Re: T wanted
Have an18 T roadster 12k or offer with spare motor