MTFCA Forum

Some pictures are of Model T parts and other contain parts similar to T, so you can get the idea. The idea is to use worn disfunctional parts modified to work the idea. This link has has some really neat ideas
Old worn dull reflectors -
reflector.png
could replace rivets with hook eyes for coats, hats , keys etc
rack.jpg
Could used split rim...

Oh Dear! Looks like at the end of the 21st century a true aficionado of the Motor Vehicle will have a choice of vehicles with clutch, manual transmission, suicide clutch, side hand shiftier, non hydraulic brakes, wheels with drum brakes, key start, and more. And there will be classes available from community education on how to drive a non...

Hello. I've owned my 1926 roadster for about two years now and I am replacing the second head gasket that has blown in the same place after about 11 months. The engine has a lot of upgrades that were done by the previous owner. I know it has aluminum pistons,plus an aluminum Z head, Bosch distributor, sure stop disk brakes and the like. The head...

I recently purchased an early 1914 Touring car and I am trying to complete the restoration started by the previous owner. I have the squeeze bulb and the horn, but I have not purchased the brass tubing to connect them because I am not sure where to mount the bulb. Does anyone know where the squeeze bulb was mounted from the factory in October of...

Today I stripped a rear axle assembly I recently bought at a swap meet. There were plenty of really good bits. Once I cleaned them up I discovered four axle bearings measuring just .0005 - .003 wear. Of particular interest was the fact that
there were 3 different bearings, one Hyatt, one just like a Hyatt and two Pollard brand English made...

For those of you that live in areas with vapor recovery boot of gas pumps, you'll know what I am talking about.
I filled up one day and the guy handed me his gas clip out of his back pocket. It was made out of aluminum and it held back the boot that otherwide needs to be held with your hand while filling the gas tank. Otherwise it will shut off...

I got home ok, hope everyone else did too.
Got to thinking about this years Luray, most vendors ever there I think. Believe I saw a figure of high 60’s. Lots of really good parts, like Hershey of a few years ago.
Any way, I got to thinking I did better selling and buying that I have at the last few years at Hershey. And that was in a lot less...

My Dad got word of a wrecking yard in Joy and loved me enough to take me as a kid. This was in the early 60’s. Joy was an unincorporated spot in the road miles from anywhere who’s only business was a beer store. The wrecking yard, located a couple of miles from town on a dirt road, a place time had forgot. The owner, a old man had lost his legs in...

I recently purchased a 1926 Ford Model T Touring and really do not know much about it except I have always wanted one. I am sure everyone here understands that. The mechanics part of it I get. I have restored many old tractors and cars. I am in the process of rewiring it. It did not have an alternator, but did have 6volt battery. When I went to...

I need a carb for my 1920 engine.( I do not have a carb for a core). Snyders catalog offers a new holly carb for $272.00 without a core which is about the same price as having one rebuilt. Has anyone had any experience with this carb? I should mention this car will only be used in town not on the highway.

Hi Folks, wondering if anyone knows the approximate weight of a 1926 Model T roadster body, where everything has been removed. (No steering column, no fuel tank, no interior, no turtle deck, etc)

Mine has some significant rust issues and I want to get the body off of the frame so I can evaluate the issue better and hopefully figure out best...

Hemmings side magazine “classic cars” has a 2 part article starting this month on rebuilding the model T rear axle. I didn’t read it yet but lots of nice color pics.

Just finished my first order from Birdhaven. A very pleasant experience!
Dan

IMG_6070.JPG
Tongue depressor, Gorilla tape.

Something weird is going on, in my post in the Forum Support Questions section. I really would like to talk to or hear back from one of you if you know anything. Please!

Engines have vibration periods which are speeds at which they vibrate, in one way or another, more than at other speeds. These periods are more noticeable in many antique vehicles with more or less rigid engine mounts and no crankshaft counterweights or harmonic balancers. Does anyone have information on what RPM range(s) or road speeds in high...

A friend has a dilemma about his T and asked me if I could shed any information. I suggested to clean the MAG post but I am not sure if this is the remedy. His engine starts on BAT but not on MAG. The engine runs smoothly on BAT but rough on MAG. The T is a '22. Any and all input is appreciated.

Hey y'all!
A week from today is the last day to register to become a Swap Vendor for Homecoming. Any registration after June 1st, the swap meet space goes from $15 to $25 a space. Save some money and sign up today!

-NB

I rebuilt a motor/transmission for my '25 and have now decided to put it in my '26 Coupe. I really don't want to mess with the nice original floor boards so I'll need to replace or bend the low speed pedal (rather than pull the hogshead and change the pedal and shaft). My question is; is it safe to mig or arc weld a correct pedal to the stub of...

I understand we are working with a lot of repro stuff but does anyone make a rear axle grease retainer cap that fits ? Put new caps on and discovered the outer flat surface is getting scraped by the recess in the hub. Tapped retainer on further same problem and when I tighten the axle nut using a 2 foot bar (as per the book) the wheel will not...

Hey, I've got a quick logistics question on the swap meet. I've never been there, so I don't know the layout. If I drive in in the morning with a trailer, can I unload it during the setup time and park it somewhere else (I see it says there's no trailer parking at the museum)? I want to have a couple spaces there (not enough to park my giant...

English Hogshead.jpg

This drawing of an English hogshead turned up on one of the FB Model T pages. Seeing the internal low band adjustment and the external adjustments for brake and reverse, exactly the opposite if the USA setup, got me to wondering: Why have any internal adjustment at all? Why didn't they make external adjusters for all...

Hi, I am trying to get my great grandpa's 1926 Model T in running condition. It has a Holley vaporizer that looks original but has a lot of vacuum leaks so I found one and ordered a rebuilt one from Blue Oval Classics. It arrived today and I was looking it over close, I see that the air damper thing is spring loaded. From prior forums, it appears...

Is there any swap meets with T parts on the eastern side of the US any time in the next couple months?
On the Smokstak site where I post about tractors and engines and such there is a section for show postings and dates, But I don't see 1 here.

Anybody who was around Stan for more than a few minutes knew that he was a great story teller. I'm going to take the liberty to repeat a story that he told me at the Bakersfield swap meet about four or five years ago. The story wasn't recorded, so I can't give it to you word for word. But I'll tell it just as accurately as I can.

Stan related...

I have one coil that sparks on battery but that same coil does not spark when running on magneto. It makes ZERO difference when I place it in the box.

What say you?

I have a full set of original Dayton wire wheels and hubs for my speedster. One of the rear hubs (the left side) is ratty in the taper. The keyway is good, but the taper is oddly worn. Has any one had the taper of a hub rebuilt? And if yes, how and by who?

Failing that, any ideas on where I could find a replacement?

Being in Alaska, it’s very...

Hello Forum, I’ve been looking for a new or used KRW reproduction gap gauge. So far to late or no luck. I’ve checked with all the vendors and they say not in stock or not available. Are they still reproducing the gap gauge? As of late we have lost a lot of craftsman through retirement or passing. Just checking if anyone has any information...

Dennis Fleming with Gang and Luray VFW,

I have to say without a doubt you folks really made my dear old Dad (Robert E Lee) very happy in his final years at Luray! He always told me about the good ole days of swap meets of 1950’s, 1960’s, and how it used to be before all the commercialism came into the picture.

You folks really made everyone...

-
This weekend I came across this in Colorado Springs.
What do you think?
-

Saw this on a TT for sale on eBay

The annual Kapunda swap meet was back on again this year, bigger and better than it was prior to Covid restrictions. My find of the century was a
T 2178 spark plug wrench to fill the tool roll in my 1912 Haigh's chocolate van. I'd been looking for one for forever! The fellow who had it thought it was highly collectable rather than useful, so he...

If Henry Ford is responsible for 15 Million Automobiles. How many motors did Henry Ford manufacture? Looking at the history of the Model T, there are Model T motors and drive trains in tanks, mowers, tractors, construction equipment and more. Or are these motors that appear in non-automobile use, salvaged from wrecks? What was the manufacture...

Anyone driving through mud today ? :lol:

Someone is currently advertising a number of spark plugs on the forum and is listing their thread forms and diameters. There are differences in these plugs. How do you determine what is correct for your head? Is there .a chart that specs what thread fits what year? My searching reveals only piecemeal information, but I am an amateur at search....

A5ACA6A6-A745-4C09-B3F3-D1E0E5C0F39A.jpeg 4715C42B-6BA7-4516-B222-5C3760361AF7.jpeg 1E8EDDBC-BCD0-4D27-AB24-6E7F2F285FB9.jpeg 37596116-8EC3-441C-8317-FDD01551D95F.jpeg

Stripping wheel paint in the rain. IMG_0332.jpg
Son of Bimel correct Ford wheel is stripped, wire brushed, phosphoric acid metal prepped and about to start painting. IMG_0333.jpg

23T..Tie Rod lever oil cups. I am missing the cap off one of my oil cups. It sure looks like there is a hex at the bottom, and it would screw out. But, all the oilers I see are press in. Are they all press in type? Thanks..Tommy

Our Touring is 100 today! :D

23T..My trunk latch doesn't have a key, and doesn't have the thing that the key moves. Do I need a whole new assembly, and do I have to drill out rivets to install it? Thanks..Tommy

I am finishing the restoration of a 1914 touring car and I have realized there are a few parts that are not made anymore that can be a little harder to find a high quality working replacement for....example brass horn or speedometer. I am lucky that I started with a mostly complete car, but have faced some challenges finding good parts. I was...

Anybody have any recommendations on the best brake light switch for my 27 T? It currently has a switch that was rigged up by a past owner using a lever operated mechanical switch connected to the pedal arm using wire and a spring. It sometimes sticks and keeps the light on. I would like to install a dependable switch and see that there are several...

Is it possible to tighten the hinges on a 1914 windshield?
The top section on my roadster has a tendency to flop back to match the angle of the lower section while driving. I made an attempt to tighten the slotted screw head on the inside of each hinge to no avail. Any help is greatly appreciated! Thanks!

I make it a point to stop and visit “ The Richmond Boys “
whenever I have an unusual - obscure - rare example
of auto history ✅

On May 26th in the afternoon I will be stopping at
The Wayne County Historical Society to show
a 1917 White Four Passenger Sedan 👍

A largely original survivor that runs and drives.

This - may be the only example of...

Found this at the Luray swap meet.
Is this an original box?
Looking at it I have a few questions.
The bottom has Made in USA with a number, what was the number, part#?
Does the S indicate anyting?
Does anyone have a box apart showing the metal parts?
The rivets on the side, how do they pin the handle.
Seeing the metal parts would explain the...

So I found a repro horn at Luray and tried jumping it off my battery. and It's not working. Do they sell a new circuitboard for these? Everything inside look new. No signs of water or corrosion.

I have had the springs blast cleaned to bare metal and have applied a Rust-Oleum primer as shown in the attached photos. I plan to paint each leaf with a Rust-Oleum satin. I will then brush a graphite slip paint to the bottom of each leaf, except the bottom leaf.

Any comments?

I will provide up dates on the restoration in parts so we don't have a long list of items under one topic.

Primer on spring leafs.

Hey all!
Only 4 weeks until Homecoming in Richmond! Hope to meet you there!

-NB

Arranged a visit to Craig Beek's Model T Museum Today for a neighbors Grandfather. Took a few photo's
IMG_2042.JPG
South side.jpg
IMG_2045.JPG
For sale? Body is in the crate - missing the engine
IMG_2047.JPG

I see a recommendation of 27 PSI all around for balloon tires on a runabout in the 1926 Ford Owner's Manual. Does that sound correct?

This screwdriver sold recently on eBay. I believe the photos might be a good reference for anyone searching for an original Model T tool kit screwdriver.

s-l400-8.jpg

s-l400-9.jpg

I just noticed a pad on the bottom of the body where the rear spring sets (see photo). I am aware that there is a rubber pad between the top leaf and the cross member, but did not know there is one on top of the spring unit. This is on a 1927 coupe.

I am interested buying a 1909_1912 model t touring.

Just came across this old postcard in a friends old car archives. It was sent by Warwick Eastwood, in Pasadena Ca. On the backside, it states “this is my 1909 T touring, engine #714. I found it here in Pasadena where it had been in storage since 1923. Leonard Davis used this car in the Ford film, American Road”
If the car is owned by anyone here,...

Anyone have any idea where a new guy could find Hack plans? Local new guy ask me. Thanks Dan

Model A's, Model T's, Girls in convertibles, Even a hot rod sneaked in,,,,,

A lot of times when you take something apart you can figure out why somebody quit using it. I bet they experienced hard starting and a bad idle. The spray needle wore a hole right through the tubing.

There will more information on this meet from the club officers. But I want to let you all know the Model T Swap meet will be on Sunday, June 13 in the park on the south side of town of Farmington MN.. In the past, vendors can come in starting at 7 a.m. and other at 8 a.m. The cost is low and there should be a food truck and there are real...

I noticed the posting about model T wood plans.
So I have a set of 15-20 touring wood plans by
“M Miller” dated 1969!! I have used these plans over the years and have been very satisfied!!
I am contemplating having them “digitized” and making them available.
I m not sure if I will get in trouble, but considering the copyright is over 50 years...

Whats the correct fuel line set up , drawing for a 1924 ? Does it have to be a perfect up from tank to downhill to carb ? above or below chassi ? close to chassi ?

In my T model puncture repair kit I carry a tin of patch cement. The tin has a nice inbuilt brush in the lid. The last 1/2 of goo went thick, so I had to buy a replacement can.

The can and brush are very handy, so I dug out what I could of the thickened goo. My go to medium for any cleaning job is lacquer thinners, so I half filled the can and...

So I bought this speedometer at Luray. Trying to ID it. I can't find a company name one it. Unless it's AC. Anyone recognize it?

IMG_4481.jpeg

Is the large ring (I have one) universal?

The picture shows the timer when the spark lever is fully retarded.

I can't seem to get another picture loaded, but it is of the timer when the spark is fully advanced; it's rubbing the belt.

Currently, the engine will run roughly on battery, but getting it started is a chore with frequent backfires through the carburetor which is a
Kingston...

20 wood cab truck, running. $6000
27??? Speedster with rajo, project but mostly complete. $5750

Highlites - 40 Chevy cabover, 21,000 - 29 A roadster, original project 6,000; Model A coupe with pickup box 6,000; 58 Deville 15,750; Montana Power gas sign 16 x 32 inches $14,000; several cans in the 1,000 range. Willys FC 150 project 6,000; Chevy 5...

What is the preferred procedure to install rim bolts into the fellows on a 1925 Model TT.

Hello....I see several types of external engine oilers that can be added to send extra oil to the front of the engine.
.
I want something that is fairly easy to add onto an engine without tearing it apart....Here are a couple I am thinking of...
.

and also

.
Just wondering what the pros and cons were to each one of these kits and wondering if...

There have been many posts on this forum about Z and P high compression heads. In no post have I ever read where someone successfully milled even as much as a 32nd of an inch (.031) off of a Prus head. Does anyone know if this is possible, assuming the block has stock deck height?

Then on the subject of Z heads, occasionally, someone will post...

Found another keyboard and an almost complete set of keys at Luray Saturday morning. These things multiply faster than they say T’s do! This makes number six! I think I may have a real problem now....... I might have to build some more wall space at this rate. This board is marked BASCO but is oddly similar to my Automotive Specialty Corp. board....

I am in the process of removing the glass from the windows in my 1927 coupe. The photos show the windows. I have removed the hardened rubber on the inside of the rear window, but I haven't tried to push the glass out. I would appreciate any comments/suggestions on how to proceed.

4D73BB17-5552-4B2C-9951-F1CFD88C5B3E.jpeg

What year of cylinder head is this? Thanks in advance. Pete

I guess I’ve overlooked this for a long time. I have a early pair of flared E&J side lamps and a tail light that came with my 09/10 (said that for you Darryl). I just noticed that the jewel on each lamp is a different color. I knew that the earliest lamps have a smoothed non faceted jewel but never notice that the drivers side has a green jewel...

hello. I'm helping a friend with his 1913 touring barn find. It is very rough but looks like it's all there. Can someone send me pictures of running board braces? This 13 has none. My 15 touring has three on each side. Thank's, bobt

So, I had a fantastic time at luray and got a bunch of stuff! Among my finds were 4 toolboxes, radiator caps. Spedomoters, and much more! When I unloaded my stuff today, I found I had left behind a box of parts and stuff I bought. There were about 40 model t magazines, a battery charger, 4 champion spark plugs, and a Stewart or other brand...

I'm getting my Model T ready for a tour in two weeks. The fuel on/off valve on the carb has been sticky so I decided to try to lap the valve and lube it with some EZ Turn. Over the last couple of days it also developed a slow leak at the valve so I decided it couldn't wait.

I removed the valve today and lapped and lubed it without incident. I...

I have a new (2019) Bergs low (black) radiator. I put a motometer Jr. and winged cap on it. After 2000 miles the neck came loose and I had it soldered back on. Today, after 1200 additional miles, it appears to be coming loose again. After fixing it the first time I changed the wings to a dogbone (lighter weight) but kept the motometer.

I know...

236EF251-D36F-4CD9-978B-952E2C593BCE.jpeg

Took this snap shot off a framed city scape, West Milton, Ohio, center door with cowl lamps.

D1BF0BE2-4C12-46C8-8C92-12BD25789603.jpeg

Story I bought one of the last Model T's made. It has the vaporizer carb Long story, the seller started it right up. Me NO failure to start and run . SO I need to learn to clean and adjust this new piece of technology so I can start it and drive with my 13 year old grandson. Basically fuel starvation The other simple fast solution is I have a new...

BBF4AC09-6529-40B9-8AF3-DFB4EA32B71B.jpeg

I'm pretty sure pin 3342 is the reason my 1919 tourer won't shift into high gear. Can someone please take a look at the picture and tell me if there's an easy way to fix that without tearing the engine apart?

I have a complete big drum rear axle with safety hubs. There is a complete rear end with e emergency brake bands, torque tube and radius rods. The drums are wire wheel hubs. I would like to sell as a complete unit for pick up at my location. This was in my speedster for a few years. I converted to a Ruckstell with hydraulic brakes and these drums...

New Autolite 14MM threads, what should the gap be?

I've ordered the disk brake kit and I need to let them know if I have the safety hubs or not. How can I tell if the prior owner installed them? I doubt it but thought I'd double check.
Thanks,
Mike

I am experimenting trying to find the best procedure for a successful hand crank start on my 23 T. If I use full choke, and a couple of 9 to 12 pulls with ignition off, it fires right away with ignition, but doesn't keep running. I tried 4 choke pulls, but then I get gas running out the carb. Is the fuel coming out of some vent, or is the fuel...

I found someone local, advertising a good looking and according to him, good running '22 centerdoor. I have offered to trade our nice '28 A Sport Coupe for it. I hope he agrees to the trade. The CD has a Ruxtell, rebuilt demountables, Rocky Mtn brakes, fat man steering wheel, and bud vases. My wife loves those. A centerdoor is my most wanted body...

I am installing a top on my 24 touring. Has anyone installed a kit from cartouche? Iv watched a few videos and there kit install seems to be different then how clastique installs there kit . Particularly how the wind breaker installs at the windshield. Has anyone installed this kit and have pictures and pointers on there ? Thanks in advance

For the next time you can't find what you need....

Does anyone know when Ford went from the one piece dust ring held on with a screw in front of the terminal stud to the split type held with a bolt and nut? McCalley's book shows a generator on page 277 with the early setup. The stud is not attached to the buss bar like the later ones. Pictures don't want to post today!

Stevens tool number T-256 is a Stevens valve stem wedge. Lengthens the valve stem without distortion!

What did you find at Luray today? Dad and I got some good finds! With reasonable prices and great selection from quality vendors, this was our first year attending but will not be our last!

Hey all!
BIG NEWS TODAY! The Greater St. Louis Chapter's Quick Assembly Team will be doing 2 demonstrations in Richmond for our Homecoming event! Do you have any questions about Homecoming or do you still need to reserve a room? Click on the link below to find everything you're looking for on our website!

-NB