Wire wheel ID
Forum rules
If you need help logging in, or have question about how something works, use the Support forum located here Support Forum
Complete set of Forum Rules Forum Rules
If you need help logging in, or have question about how something works, use the Support forum located here Support Forum
Complete set of Forum Rules Forum Rules
-
RadRacer203
Topic author - Posts: 120
- Joined: Sun Nov 12, 2023 8:22 am
- First Name: Michael
- Last Name: Stroz
- * REQUIRED* Type and Year of Model Ts owned: 1926 Coupe
- Location: Grand Isle, Vermont
Wire wheel ID
Picking up a '27 Touring in a few weeks, planning on taking the wire wheels and Ruckstell for my '26 coupe, then making it run and pass it along to someone else. I'm just curious if anyone can identify the wire wheels from a couple pictures, just want to make sure they aren't A wheels or something.
-
Kevin Pharis
- Posts: 1558
- Joined: Thu Jan 10, 2019 3:54 pm
- First Name: Kevin
- Last Name: Pharis
- Location: Sacramento CA
- Contact:
-
RadRacer203
Topic author - Posts: 120
- Joined: Sun Nov 12, 2023 8:22 am
- First Name: Michael
- Last Name: Stroz
- * REQUIRED* Type and Year of Model Ts owned: 1926 Coupe
- Location: Grand Isle, Vermont
Re: Wire wheel ID
Ok thanks. I wish I had better pictures, but this is about all I have till I actually pick it up in a few weeks
-
TRDxB2
- Posts: 6260
- Joined: Tue Jan 08, 2019 4:56 pm
- First Name: Frank
- Last Name: Brandi
- * REQUIRED* Type and Year of Model Ts owned: Speedsters (1919 w 1926 upgrades), 1926 (Ricardo Head)
- Location: Moline IL
- Board Member Since: 2018
Re: Wire wheel ID
The first picture - does that wheel have front wheel brakes?
--
These are likely Model T since they are in a pile of T parts. But the one wheel has some rather large holes for studs
--
These are likely Model T since they are in a pile of T parts. But the one wheel has some rather large holes for studs
--
The past is a great place and I don't want to erase it or to regret it, but I don't want to be its prisoner either.
Mick Jagger
Mick Jagger
-
RadRacer203
Topic author - Posts: 120
- Joined: Sun Nov 12, 2023 8:22 am
- First Name: Michael
- Last Name: Stroz
- * REQUIRED* Type and Year of Model Ts owned: 1926 Coupe
- Location: Grand Isle, Vermont
Re: Wire wheel ID
I know the seller said a couple wheels might be a bit damaged, so that could explain the larger holes on the one. As far as the front wheels go, I have no idea if it has front brakes. Would be nice if it did have front brakes, and those would definitely go on my coupe, but I'm not gonna hold out too much hope
-
jsaylor
- Posts: 411
- Joined: Sun Jan 06, 2019 5:25 pm
- First Name: John
- Last Name: Saylor
- * REQUIRED* Type and Year of Model Ts owned: 1921 Touring, 1927 Tudor
- Location: Citrus Heights, Ca
- Board Member Since: 1999
Re: Wire wheel ID
The Model T bolt circle is 5 inches. Model A is 5 1/2 inches with humps around the center. Hub cap is also larger. I believe a Model A complete hub and bearings will fit the the T spindle but you must add a locking nut to keep the bearings in place.
-
Allan
- Posts: 6609
- Joined: Sun Jan 06, 2019 7:21 pm
- First Name: Allan
- Last Name: Bennett
- * REQUIRED* Type and Year of Model Ts owned: 1912 van, 1917 shooting brake, 1929 roadster buckboard, 1924 tourer, 1925 barn find buckboard, 1925 D &F wide body roadster, 1927LHD Tudor sedan.
- Location: Gawler, Australia
Re: Wire wheel ID
They look like T wheels to me. A model wheels are easy to identify. They have a raised ridge pressed outwards between each stud hole. This stiffens up the hub so the wheels do not crack between the stud holes like some T wheels do.
Allan from down under.
Allan from down under.
-
RadRacer203
Topic author - Posts: 120
- Joined: Sun Nov 12, 2023 8:22 am
- First Name: Michael
- Last Name: Stroz
- * REQUIRED* Type and Year of Model Ts owned: 1926 Coupe
- Location: Grand Isle, Vermont
Re: Wire wheel ID
Ah, I see what you mean, I had never noticed that difference before, but that's very good to know