Gasket application
Forum rules
If you need help logging in, or have question about how something works, use the Support forum located here Support Forum
Complete set of Forum Rules Forum Rules
If you need help logging in, or have question about how something works, use the Support forum located here Support Forum
Complete set of Forum Rules Forum Rules
-
Bill Robinson
Topic author - Posts: 309
- Joined: Sun Jan 06, 2019 2:24 pm
- First Name: Bill
- Last Name: Robinson
- * REQUIRED* Type and Year of Model Ts owned: '21 Depot Hack, '25 Touring Car, '26 Roadster Pickup, '27 Tudor, & another '27 Tudor
- Location: Salty Bottom, ALABAMA AL
- Board Member Since: 1999
- Contact:
Gasket application
I know that some folks apply a gasket- (example: Crankcase pan lower cover gasket) by applying RTV sealant between the engine block and the gasket (apply to one side of the gasket), and then applying a real heavy grease to the cover rather that use RTV, then bolt the cover to the block. To be clear one side of the gasket gets RTV and the other side gets heavy grease. The goal is easy removal and re-use of the gasket. My question is- has anyone ever used the aviation product called EZ TURN? It's not effected by water, oil, gas and it is used on many aviation applications to this day.
- Attachments
-
- EZ Turn Lubricant.jpg (14.04 KiB) Viewed 993 times
-
speedytinc
- Posts: 4725
- Joined: Fri Feb 12, 2021 12:24 pm
- First Name: john
- Last Name: karvaly
- * REQUIRED* Type and Year of Model Ts owned: 14/15 wide track roadster. 23 touring, 27 roadster pickup, 20ish rajo touring
- Location: orange, ca
- Board Member Since: 2020
Re: Gasket application
My method is to use ultra black on both sides of the gasket then spread a thin layer of motor oil on the mating gasket surface where you want to cleanly remove. The silicone will seal & slick well, but peel clean without damaging the gasket. To reseal, add a small bead on top of the old, dried silicone & re oil the one surface as originally done. Use a drop on each bolt thread for a dry/drip-less cover. Would EZ turn work instead of oil or grease? Yes, but why use such an expensive product when plain oil does the job?
-
big2bird
- Posts: 449
- Joined: Mon Sep 14, 2020 10:57 pm
- First Name: Jeffrey
- Last Name: Hausey
- * REQUIRED* Type and Year of Model Ts owned: Early 23 Touring
- Location: Anaheim, Ca.
- Board Member Since: 2020
Re: Gasket application
EZ Turn is the cure for petcocks and sediment bowl shut off.
I would not use it for gaskets, but it might work. Dunno.
I would not use it for gaskets, but it might work. Dunno.
-
TRDxB2
- Posts: 6261
- Joined: Tue Jan 08, 2019 4:56 pm
- First Name: Frank
- Last Name: Brandi
- * REQUIRED* Type and Year of Model Ts owned: Speedsters (1919 w 1926 upgrades), 1926 (Ricardo Head)
- Location: Moline IL
- Board Member Since: 2018
Re: Gasket application
Does this help?Bill Robinson wrote: ↑Fri May 23, 2025 5:03 pmI know that some folks apply a gasket- (example: Crankcase pan lower cover gasket) by applying RTV sealant between the engine block and the gasket (apply to one side of the gasket), and then applying a real heavy grease to the cover rather that use RTV, then bolt the cover to the block. To be clear one side of the gasket gets RTV and the other side gets heavy grease. The goal is easy removal and re-use of the gasket. My question is- has anyone ever used the aviation product called EZ TURN? It's not effected by water, oil, gas and it is used on many aviation applications to this day.
- Attachments
-
The past is a great place and I don't want to erase it or to regret it, but I don't want to be its prisoner either.
Mick Jagger
Mick Jagger
-
Dan Hatch
- Posts: 5018
- Joined: Tue Jan 08, 2019 7:31 pm
- First Name: Dan
- Last Name: Hatch
- Location: Alabama
Re: Gasket application
Bill I have found that a big problem with these new gaskets is not leaking past them. It is leaking through them. Like a wick on kerosene lamp.
I coat them on all sides with gasket sealer. It soaks in and helps stop that. Then RTV, but that stops what you are trying to accomplish.
Just what I have found. Dan
I coat them on all sides with gasket sealer. It soaks in and helps stop that. Then RTV, but that stops what you are trying to accomplish.
Just what I have found. Dan