Drive Train Assembly Order

Discuss all things Model T related.
Forum rules
If you need help logging in, or have question about how something works, use the Support forum located here Support Forum
Complete set of Forum Rules Forum Rules
Post Reply Previous topicNext topic

Topic author
mortier
Posts: 95
Joined: Sun Jan 06, 2019 7:16 pm
First Name: Philip
Last Name: Jamison
* REQUIRED* Type and Year of Model Ts owned: 1915 Roadster
Location: PA

Drive Train Assembly Order

Post by mortier » Mon Aug 25, 2025 10:54 am

I have the engine, rear axle, and rear spring out of my T and ready for installation. Any idea for the best order of assembly? Photo shows rear spring going in, but I'm wondering if I should install the axle first.
IMG_1571.jpg
Top

Dan Hatch
Posts: 5119
Joined: Tue Jan 08, 2019 7:31 pm
First Name: Dan
Last Name: Hatch
Location: Alabama

Re: Drive Train Assembly Order

Post by Dan Hatch » Mon Aug 25, 2025 11:10 am

Think the Service Manual has that information.
Top
User avatar

jsaylor
Posts: 421
Joined: Sun Jan 06, 2019 5:25 pm
First Name: John
Last Name: Saylor
* REQUIRED* Type and Year of Model Ts owned: 1921 Touring, 1927 Tudor
Location: Citrus Heights, Ca
Board Member Since: 1999

Re: Drive Train Assembly Order

Post by jsaylor » Mon Aug 25, 2025 12:46 pm

I always put the spring in first, being sure to center the square head center bolt into the frame. Then you can use the weight of the car and a small block of wood under the ends to help spread the shackles into the backing plates.
Top

AndyClary
Posts: 851
Joined: Sun Jan 06, 2019 11:15 am
First Name: Andrew
Last Name: Clary
* REQUIRED* Type and Year of Model Ts owned: 1914 Runabout 1926 Coupe. Mercury Speedster #1249
Location: Usa

Re: Drive Train Assembly Order

Post by AndyClary » Mon Aug 25, 2025 3:48 pm

I agree with John on the rear spring going on first. It doesn’t make a lot of difference if you put the engine or rear end in first. I’ve always found it easier to stick the u-joint into the motor than to stick the motor to the u-joint.

Andy
Top
User avatar

walber
Posts: 244
Joined: Sun Jan 06, 2019 12:55 pm
First Name: Walt
Last Name: Berdan
* REQUIRED* Type and Year of Model Ts owned: '18 Speedster had 25 touring and 26 coupe
Location: Bellevue, WA

Re: Drive Train Assembly Order

Post by walber » Mon Aug 25, 2025 4:42 pm

Engine, rear spring, connect rear axle to transmission, then shackle axle to spring (using car weight & 2x4 blocks to spread spring).
Top

Topic author
mortier
Posts: 95
Joined: Sun Jan 06, 2019 7:16 pm
First Name: Philip
Last Name: Jamison
* REQUIRED* Type and Year of Model Ts owned: 1915 Roadster
Location: PA

Re: Drive Train Assembly Order

Post by mortier » Mon Aug 25, 2025 6:46 pm

Thanks. Hope to get it together this week.
Top

Allan
Posts: 6762
Joined: Sun Jan 06, 2019 7:21 pm
First Name: Allan
Last Name: Bennett
* REQUIRED* Type and Year of Model Ts owned: 1912 van, 1917 shooting brake, 1929 roadster buckboard, 1924 tourer, 1925 barn find buckboard, 1925 D &F wide body roadster, 1927LHD Tudor sedan.
Location: Gawler, Australia

Re: Drive Train Assembly Order

Post by Allan » Mon Aug 25, 2025 8:55 pm

Just leave tightening the rear spring U bolts till last. That way you have some control over how the car sits on the road.

Allan from down under.
Top
User avatar

babychadwick
Posts: 693
Joined: Tue Jan 08, 2019 7:03 am
First Name: Chad
Last Name: Azevedo
* REQUIRED* Type and Year of Model Ts owned: 1926 Boattail speedster, 1912 Tourabout project, 1927 Speedster (build), 1929 Buick (future T tow car)
Location: Henderson, TN
Board Member Since: 1999

Re: Drive Train Assembly Order

Post by babychadwick » Tue Aug 26, 2025 8:22 am

AndyClary wrote: ↑
Mon Aug 25, 2025 3:48 pm
 I agree with John on the rear spring going on first. It doesn’t make a lot of difference if you put the engine or rear end in first. I’ve always found it easier to stick the u-joint into the motor than to stick the motor to the u-joint.

Andy
I have found the opposite to be true, of course I am typically wheeling the rear end in and its rotating as you try to line it up. With the engine going in you can turn the crank to get the right alignment. However, last time I put the ruxtel in I was working on uneven gravel/dirt and it slid in perfectly on the first try!!! My son didn't understand why I was dancing but he will in the future....
"Those who fail to plan, plan to fail"
Top

Allan
Posts: 6762
Joined: Sun Jan 06, 2019 7:21 pm
First Name: Allan
Last Name: Bennett
* REQUIRED* Type and Year of Model Ts owned: 1912 van, 1917 shooting brake, 1929 roadster buckboard, 1924 tourer, 1925 barn find buckboard, 1925 D &F wide body roadster, 1927LHD Tudor sedan.
Location: Gawler, Australia

Re: Drive Train Assembly Order

Post by Allan » Tue Aug 26, 2025 8:29 am

I put the engine in last. Aligning the U joint square is a piece of cake if one rear wheel is jacked off the ground. My Stevens tool holds the square and it can easily be used to rotate it into alignment when the wheel is jacked.

Allan from down under.
Top
User avatar

Mark Gregush
Posts: 5396
Joined: Sat Jan 05, 2019 1:57 pm
First Name: Mark
Last Name: Gregush
* REQUIRED* Type and Year of Model Ts owned: 1925 cutdown PU, 1948 F2 Ford flat head 6 pickup 3 speed
Location: Portland Or
Board Member Since: 1999

Re: Drive Train Assembly Order

Post by Mark Gregush » Tue Aug 26, 2025 11:03 am

I would stick the rear end in first. Going to give you a more stable platform to work with even with one wheel off the ground.
I know the voices aren't real but damn they have some good ideas! :shock:

1925 Cut down pickup
1948 Ford F2 pickup
Top
Post Reply Previous topicNext topic

Return to “General Discussion Forum”