Cam nut wrench
Forum rules
If you need help logging in, or have question about how something works, use the Support forum located here Support Forum
Complete set of Forum Rules Forum Rules
If you need help logging in, or have question about how something works, use the Support forum located here Support Forum
Complete set of Forum Rules Forum Rules
-
Tmooreheadf
Topic author - Posts: 414
- Joined: Sun Jan 06, 2019 7:31 pm
- First Name: Tom
- Last Name: Moorehead
- * REQUIRED* Type and Year of Model Ts owned: 24 Touring, 25 Coupe,
- Location: Louisville, KY
Cam nut wrench
Most of the time, I’m a cheap A. Sunday, I started taking apart the front end of our 25 couple to find a cam noise, that turned out to be a front cam bearing. While ordering parts, I noticed in a Snyder’s catalog a cam nut wrench. I don’t need one very often, but what the heck! I ordered one with the rest of the stuff. Without a doubt, the best specialized tool I have bought in a long time. I had already removed the cam not and messed it up doing so. Tonite, while assembling the cam gear to the cam shaft, I used the new tool! Hot damn! I’m thinking if I ever have to remove or install the cam nut again, it’ll be a piece of cake, assuming I can find it when needed next time.
-
RajoRacer
- Posts: 5171
- Joined: Sun Jan 06, 2019 12:18 pm
- First Name: Steve
- Last Name: Tomaso
- * REQUIRED* Type and Year of Model Ts owned: 1914 Touring, 1919 Centerdoor, 1924 TT C-Cab Express, 1925 Racer
- Location: Longbranch, WA
- Board Member Since: 2001
Re: Cam nut wrench
I agree - one of the best specialty sockets ever ! I also have the Ford Z wrench but the new socket is the best !
-
AndyClary
- Posts: 835
- Joined: Sun Jan 06, 2019 11:15 am
- First Name: Andrew
- Last Name: Clary
- * REQUIRED* Type and Year of Model Ts owned: 1914 Runabout 1926 Coupe. Mercury Speedster #1249
- Location: Usa
Re: Cam nut wrench
I also use it on the front wheel bearings.
Andy
Andy
Last edited by AndyClary on Thu Aug 22, 2024 8:16 am, edited 1 time in total.
-
Allan
- Posts: 6609
- Joined: Sun Jan 06, 2019 7:21 pm
- First Name: Allan
- Last Name: Bennett
- * REQUIRED* Type and Year of Model Ts owned: 1912 van, 1917 shooting brake, 1929 roadster buckboard, 1924 tourer, 1925 barn find buckboard, 1925 D &F wide body roadster, 1927LHD Tudor sedan.
- Location: Gawler, Australia
Re: Cam nut wrench
The Ford Z wrench is next to useless on its own. The crank in the handle means the wrench will cam off the nut, damaging it as it does. The more tension you apply, the more likely it will cam off the nut.
I use it with a helper. I have sleeve with a washer welded on one end which goes over the cam snout. When I fit the wrench to the cam nut, a larger washer goes against the wrench and the open end of the sleeve engages on this Then I fit the timer nut to hold it all in place. Now the wrench is captive on the cam nut and will not cam off.
Allan from down under.
I use it with a helper. I have sleeve with a washer welded on one end which goes over the cam snout. When I fit the wrench to the cam nut, a larger washer goes against the wrench and the open end of the sleeve engages on this Then I fit the timer nut to hold it all in place. Now the wrench is captive on the cam nut and will not cam off.
Allan from down under.
-
Pep C Strebeck
- Posts: 578
- Joined: Sun Jan 06, 2019 11:12 am
- First Name: Joseph
- Last Name: M
- Location: MI
Re: Cam nut wrench
I like the Snap-On 36F socket.
Not my socket, don't have it in front of me to take a photo. The socket is a lot bigger than you think. If anyone has a Snap-On 35F Fan Shaft socket they would like to part with, please let me know.
- Cam Nut Socket.jpg (40.99 KiB) Viewed 2524 times
"Remember son, there are two ways to do this: The right way, and your way” Thanks Dad, I love you too.
LOOKING FOR A LUFKIN No. 9A Height Gage Attachment.
LOOKING FOR A LUFKIN No. 9A Height Gage Attachment.
-
BE_ZERO_BE
- Posts: 628
- Joined: Sun Jan 06, 2019 12:27 pm
- First Name: BOB
- Last Name: CASCISA
- * REQUIRED* Type and Year of Model Ts owned: 1916 TOURING
- Location: POULSBO, WA
Re: Cam nut wrench
I made one.
I found an old wheel wrench and cut out the front bearing section.
It is the exact fit for the cam nut.
I just welded it to a piece of tubing and welded that to an old socket.
It is deep enough to work on the front wheel bearing and the cam nut.
I found an old wheel wrench and cut out the front bearing section.
It is the exact fit for the cam nut.
I just welded it to a piece of tubing and welded that to an old socket.
It is deep enough to work on the front wheel bearing and the cam nut.
Respectfully Submitted,
Be_Zero_Be
I drive a Model T ... Microseconds don't matter
For every Absolute Model T Fact there are at least three exceptions.
Be_Zero_Be
I drive a Model T ... Microseconds don't matter
For every Absolute Model T Fact there are at least three exceptions.
-
AndyClary
- Posts: 835
- Joined: Sun Jan 06, 2019 11:15 am
- First Name: Andrew
- Last Name: Clary
- * REQUIRED* Type and Year of Model Ts owned: 1914 Runabout 1926 Coupe. Mercury Speedster #1249
- Location: Usa
Re: Cam nut wrench
Looks good Bob. I made a similar socket that fits the front spindle nut. You can’t use the flat ford wrench with buffalo wheels.
Andy
Andy
-
Allan
- Posts: 6609
- Joined: Sun Jan 06, 2019 7:21 pm
- First Name: Allan
- Last Name: Bennett
- * REQUIRED* Type and Year of Model Ts owned: 1912 van, 1917 shooting brake, 1929 roadster buckboard, 1924 tourer, 1925 barn find buckboard, 1925 D &F wide body roadster, 1927LHD Tudor sedan.
- Location: Gawler, Australia
Re: Cam nut wrench
Bob, your socket would work on Hayes wire wheels too. Again, the bearing is buried in the hub.
Allan from down under.
Allan from down under.
-
RajoRacer
- Posts: 5171
- Joined: Sun Jan 06, 2019 12:18 pm
- First Name: Steve
- Last Name: Tomaso
- * REQUIRED* Type and Year of Model Ts owned: 1914 Touring, 1919 Centerdoor, 1924 TT C-Cab Express, 1925 Racer
- Location: Longbranch, WA
- Board Member Since: 2001
Re: Cam nut wrench
Been searching for years Trent - that's one of the few Stevens tool I don't have !!!
-
sweet23
- Posts: 516
- Joined: Sun Jan 06, 2019 1:19 pm
- First Name: Darryl
- Last Name: Bobzin
- * REQUIRED* Type and Year of Model Ts owned: 2, '25 T Runabouts, '14 Touring
- Location: Kannapolis,NC
- Board Member Since: 2016
Re: Cam nut wrench
I have been looking for the Ford cam nut wrench 5-Z-162. It looks vey much like the Stevens tool.
- Attachments
-
-
jsaylor
- Posts: 411
- Joined: Sun Jan 06, 2019 5:25 pm
- First Name: John
- Last Name: Saylor
- * REQUIRED* Type and Year of Model Ts owned: 1921 Touring, 1927 Tudor
- Location: Citrus Heights, Ca
- Board Member Since: 1999
Re: Cam nut wrench
I use a Model A spark plug wrench. It has the right offset and fits perfect.
-
DanTreace
- Posts: 3812
- Joined: Sun Jan 06, 2019 10:56 am
- First Name: Dan
- Last Name: Treace
- * REQUIRED* Type and Year of Model Ts owned: ‘12 open express,'23 cutoff, '27 touring
- Location: North Central FL
- Board Member Since: 2000
- Contact:
Re: Cam nut wrench
Sure does!
The best way is always the simplest. The attics of the world are cluttered up with complicated failures. Henry Ford
Don’t find fault, find a remedy; anybody can complain. Henry Ford
Don’t find fault, find a remedy; anybody can complain. Henry Ford
-
speedytinc
- Posts: 4725
- Joined: Fri Feb 12, 2021 12:24 pm
- First Name: john
- Last Name: karvaly
- * REQUIRED* Type and Year of Model Ts owned: 14/15 wide track roadster. 23 touring, 27 roadster pickup, 20ish rajo touring
- Location: orange, ca
- Board Member Since: 2020
Re: Cam nut wrench
Very effective & cheap way to go.
Best to stack some spacers & a nut on the cam to keep the wrench from slipping off & knackering the flats.
-
Craig Leach
- Posts: 1906
- Joined: Tue Jan 08, 2019 12:22 am
- First Name: craig
- Last Name: leach
- * REQUIRED* Type and Year of Model Ts owned: 1919 Firetruck/1922 Speedster
- Location: Laveen Az
Re: Cam nut wrench
I made my own from a swap meet socket ( Harbor Freight ) Cut six flats out with a die grinder & cutoff wheel, turn , heat & press a sleeve on
to strengthen the two flats. Works with a impact if stuck real bad.
Craig.
to strengthen the two flats. Works with a impact if stuck real bad.