We Have All Been Here, Right?
Forum rules
If you need help logging in, or have question about how something works, use the Support forum located here Support Forum
Complete set of Forum Rules Forum Rules
If you need help logging in, or have question about how something works, use the Support forum located here Support Forum
Complete set of Forum Rules Forum Rules
-
Henry K. Lee
Topic author - Posts: 5474
- Joined: Sun Jan 06, 2019 11:09 am
- First Name: Henry
- Last Name: Lee
- * REQUIRED* Type and Year of Model Ts owned: Many
- Location: South Pittsburg, TN
- MTFCA Life Member: YES
We Have All Been Here, Right?
THE PYRAMID OF PERSUASION!
-
Wayne Sheldon
- Posts: 4249
- Joined: Sun Jan 06, 2019 3:13 pm
- First Name: Wayne
- Last Name: Sheldon
- * REQUIRED* Type and Year of Model Ts owned: 1915 Runabout 1913 Speedster
- Location: Grass Valley California, USA
- Board Member Since: 2005
Re: We Have All Been Here, Right?
I do like the "I wasn't asking"!
Also, a lot of truth to that "Can't be tight if its a liquid".
Good stuff! Thanks for sharing those.
Also, a lot of truth to that "Can't be tight if its a liquid".
Good stuff! Thanks for sharing those.
-
Steve Jelf
- Posts: 7238
- Joined: Fri Jan 04, 2019 9:37 pm
- First Name: Steve
- Last Name: Jelf
- * REQUIRED* Type and Year of Model Ts owned: 1923 touring and a few projects
- Location: Parkerfield, Kansas
- Board Member Since: 2007
- Contact:
Re: We Have All Been Here, Right?
All that's missing is the six-foot cheater stuck on the handle of the big wrench. 
The inevitable often happens.
1915 Runabout
1923 Touring
1915 Runabout
1923 Touring
-
Rich Bingham
- Posts: 1942
- Joined: Sun Jan 06, 2019 11:23 am
- First Name: Rich
- Last Name: Bingham
- * REQUIRED* Type and Year of Model Ts owned: 1913 runabout
- Location: Blackfoot, Idaho
Re: We Have All Been Here, Right?
wayne sheldon wrote: ↑Wed Aug 07, 2019 12:35 am. . . a lot of truth to that "Can't be tight if its a liquid".
you can disassemble practically anything with a cutting torch ! "Get a horse !"
-
JTT3
- Posts: 1855
- Joined: Sun Jan 06, 2019 11:57 am
- First Name: John
- Last Name: Tannehill
- Location: Hot Coffee, MS
Re: We Have All Been Here, Right?
Henry, I noticed you missed in your tool assortment the BFH as an adjunct to the other tools.
-
Dennis Prince
- Posts: 397
- Joined: Sun Jan 06, 2019 2:36 pm
- First Name: Dennis
- Last Name: Prince
- * REQUIRED* Type and Year of Model Ts owned: 1)24 touring 2)25 TT's 1)26 roadster 2)26 tourings 1) 26coupe 1)27 funster 1)28 A pick up
- Location: Madras Oregon
- Board Member Since: 1999
Re: We Have All Been Here, Right?
By the time I get to the directional forge there is usually a box of band aids involved as well.
-
Ruxstel24
- Posts: 2345
- Joined: Sun Jan 06, 2019 11:25 am
- First Name: Dave
- Last Name: Hanlon
- * REQUIRED* Type and Year of Model Ts owned: 24 Touring car
- Location: NE Ohio
- Board Member Since: 2018
Re: We Have All Been Here, Right?
I had to heat a carrier bearing housing on a front axle half shaft the other day...I had to get away for a couple hours from the garage being smoked up so bad !! It was rough ! 
Sometimes the flaming nut buster is the only option.
Sometimes the flaming nut buster is the only option.